SBL1030CT

SBL1030CT AND SBL1040CT SCHOTTKY RECTIFIER Reverse Voltage - 30 and 40 Volts TO-220AB 0.415 (10.54) MAX. 0.370 (9.40) 0.360 (9.14) 0.154 (3.91) 0.185 (4.70) 0.175 (4.44) DIA. 0.148 (3.74) 0.055 (1.39) 0.045 (1.14) Forward Current - 10.0 Amperes FEATURES ♦ Plastic package has Underwriters Laboratory Flammability Classifications 94V-0 ♦ Metal silicon junction, majority carrier conduction ♦ Low power loss, high efficiency ♦ High current capability, low forward voltage drop ♦ High surge capacity ♦ For use in low voltage, high frequency inverters, free wheeling, and polarity protection applications ♦ Guardring for overvoltage protection ♦ High temperature soldering guaranteed: 250°C/10 seconds, 0.25" (6.35mm) from case 0.113 (2.87) 0.103 (2.62) 0.145 (3.68) 0.135 (3.43) 0.560 (14.22) 0.530 (13.46) 0.410 (10.41) 0.390 (9.91) PIN 2 0.635 (16.13) 0.625 (15.87) 1 0.160 (4.06) 0.140 (3.56) 0.560 (14.22) 0.530 (13.46) 3 0.350 (8.89) 0.330 (8.38) 1.148 (29.16) 1.118 (28.40) 0.110 (2.79) 0.100 (2.54) 0.105 (2.67) 0.095 (2.41) 0.037 (0.94) 0.027 (0.68) 0.105 (2.67) 0.095 (2.41) 0.205 (5.20) 0.195 (4.95) 0.022 (0.56) 0.014 (0.35) MECHANICAL DATA PIN 1 PIN 3 PIN 2 CASE Dimensions in inches and (millimeters) Case: JEDEC TO-220AB molded plastic body Terminals: Lead solderable per MIL-STD-750, Method 2026 Polarity: As marked Mounting Position: Any Mounting Torque: 5 in. - lbs max. Weight: 0.08 ounce, 2.24 grams MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25°C ambient temperature unless otherwise specified. SYMBOLS SBL1030CT SBL1040CT UNITS Maximum repetitive peak reverse voltage Maximum RMS voltage Maximum DC blocking voltage Maximum average forward rectified current at TC=95°C Peak forward surge current, 8.3ms single half sine-wave superimposed on rated load (JEDEC Method) Maximum instantaneous forward voltage per leg at 5.0A (NOTE 1) Maximum instantaneous reverse current at rated DC blocking voltage (NOTE 1) Typical thermal resistance (NOTE 2) Operating and storage temperature range NOTES: (1) Pulse test: 300µs pulse width, 1% duty cycle (2) Thermal resistance from junction to case per leg VRRM VRMS VDC I(AV) IFSM 30 21 30 10.0 175.0 40 28 40 Volts Volts Volts Amps Amps VF TC=25°C TC=100°C IR RΘJC TJ, TSTG 0.55 0.5 50.0 3.0 -40 to +125 Volts mA °C/W °C 4/98 RATINGS AND CHARACTERISTIC CURVES SBL1030CT AND SBL1040CT FIG. 1 - FORWARD CURRENT DERATING CURVE RESISTIVE OR INDUCTIVE LOAD FIG. 2 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT PEAK FORWARD SURGE CURRENT, AMPERES AVERAGE FORWARD CURRENT, AMPERES 12.5 10 7.5 5 2.5 0 300 250 200 150 100 50 0 TJ=TJ max. 8.3ms SINGLE HALF SINE-WAVE (JEDEC Method) 0 50 100 150 CASE TEMPERATURE, °C 1 10 NUMBER OF CYCLES AT 60 HZ 100 FIG. 4 - TYPICAL REVERSE CHARACTERISTICS PER LEG FIG. 3 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS PER LEG 50 50 INSTANTANEOUS FORWARD CURRENT, AMPERES PULSE WIDTH = 300µs 1% DUTY CYCLE TJ=125°C 10 TJ=125°C INSTANTANEOUS REVERSE CURRENT, MILLIAMPERES 10 1 TJ=75°C 1 TJ=25°C 0.1 0.1 0.01 TJ=25°C 0.01 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2 INSTANTANEOUS FORWARD VOLTAGE, VOLTS 0.001 0 20 40 60 80 100 PERCENT OF RATED PEAK REVERSE VOLTAGE, % FIG. 5 - TYPICAL JUNCTION CAPACITANCE PER LEG FIG. 6 - TYPICAL TRANSIENT THERMAL IMPEDANCE PER LEG TRANSICENTTHERMAL IMPEDANCE, °C/W 4,000 JUNCTION CAPACITANCE, pF TJ = 25°C f=1.0 MHz Vsig=50mVp-p 100 1,000 10.0 1.0 1.0 100 0.1 1.0 1 10 100 0.1 0.01 0.1 1 10.0 100 REVERSE VOLTAGE, VOLTS t, PULSE DURATION, sec.