SBLF1030

NEW PRODUCT NEW PRODUCT NEW PRODUCT SBLF1030 AND SBLF1040 SCHOTTKY ISOLATED PLASTIC RECTIFIER Reverse Voltage - 30 and 40 Volts ITO-220AC Forward Current - 10.0 Amperes FEATURES ¨ Isolated plastic package has Underwriters Laboratory Flammability Classifications 94V-0 ¨ Metal silicon junction, majority carrier conduction ¨ Low power loss,high efficiency ¨ High current capability, low forward voltage drop ¨ High surge capability ¨ For use in low voltage, high frequency inverters, free wheeling, and polarity protection applications ¨ Guardring for overvoltage protection ¨ High temperature soldering guaranteed: 250¡C/10 seconds, 0.25" (6.35mm) from case 0.405 (10.27) 0.383 (9.72) 0.188 (4.77) 0.172 (4.36) 0.110 (2.80) 0.100 (2.54) 0.140 (3.56) DIA. 0.130 (3.30) 0.131 (3.39) DIA. 0.122 (3.08) 0.600 (15.5) 0.580 (14.5) 0.676 (17.2) 0.646 (16.4) 2 0.350 (8.89) 0.330 (8.38) PIN 1 0.191 (4.85) 0.171 (4.35) 0.560 (14.22) 0.530 (13.46) 0.060 (1.52) 0.110 (2.80) 0.100 (2.54) MECHANICAL DATA 0.037 (0.94) 0.027 (0.69) 0.205 (5.20) 0.195 (4.95) PIN 1 PIN 2 0.022 (0.55) 0.014 (0.36) Dimensions in inches and (millimeters) Case: JEDEC ITO-220AC fully overmolded plastic body Terminals: Leads solderable per MIL-STD-750, Method 2026 Polarity: As marked Mounting Position: Any Mounting Torque: 5 in. - lbs. max. Weight: 0.08 ounces, 2.24 grams MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25¡C ambient temperature unless otherwise specified. SYMBOLS SBLF1030 SBLF1040 UNITS Maximum repetitive peak reverse voltage Maximum RMS voltage Maximum DC blocking voltage Maximum average forward rectified current at TC=110¡C Peak forward surge current, 8.3ms single half sine-wave superimposed on rated load (JEDEC Method) Maximum instantaneous forward voltage at 10A (NOTE 1) Maximum instantaneous reverse current at rated DC blocking voltage (NOTE 1) Typical thermal resistance (NOTE 2) Operating and storage temperature range RMS Isolation voltage from terminals to heatsink with RH ² 30% TC=25¡C TC=100¡C VRRM VRMS VDC I(AV) 30 21 30 10.0 40 28 40 Volts Volts Volts Amps IFSM VF IR RQJC TJ,TSTG VISOL 250.0 0.55 1.0 50.0 4.0 -40 to +125 4500 (NOTE 3) 3500 (NOTE 4) 1500 (NOTE 5) Amps Volts mA ¡C/W ¡C Volts NOTES: (1) Pulse test: 300ms pulse width, 1% duty cycle (2) Thermal resistance from junction to case per leg (3) Clip mounting (on case), where lead does not overlap heatsink with 0.110Ó offset. (4) Clip mounting (on case), where leads do overlap heatsink. (5) Screw mounting with 4-40 screw, where washer diameter is £ 4.9 mm (0.19Ó). 2/22/99 RATINGS AND CHARACTERISTIC CURVES SBLF1030 AND SBLF1040 FIG. 1 - FORWARD CURRENT DERATING CURVE AVERAGE FORWARD CURRENT, AMPERES 12.5 RESISTIVE OR INDUCTIVE LOAD PEAK FORWARD SURGE CURRENT, AMPERES FIG. 2 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT 300 250 200 150 100 50 0 1 10 NUMBER OF CYCLES AT 60 HZ TJ=TJ max. 8.3ms SINGLE HALF SINE-WAVE (JEDEC Method) 10 7.5 5 2.5 0 100 0 50 100 150 CASE TEMPERATURE, ¡C FIG. 4 - TYPICAL REVERSE CHARACTERISTICS FIG. 3 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS 50 50 INSTANTANEOUS FORWARD CURRENT, AMPERES 10 10 TJ=125¡C PULSE WIDTH = 300ms 1% DUTY CYCLE INSTANTANEOUS REVERSE CURRENT, MILLIAMPERES TJ=125¡C 1 TJ=75¡C 1 TJ=25¡C 0.1 0.1 0.01 TJ=25¡C 0.01 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2 INSTANTANEOUS FORWARD VOLTAGE, VOLTS 0.001 0 20 40 60 80 100 PERCENT OF RATED PEAK REVERSE VOLTAGE, % TRANSIENT THERMAL IMPEDANCE, °C/W FIG. 5 - TYPICAL JUNCTION CAPACITANCE FIG. 6 - TYPICAL TRANSIENT THERMAL IMPEDANCE 4,000 JUNCTION CAPACITANCE, pF TJ=25¡C f=1.0 MHz Vsig=50mVp-p 100 1,000 10.0 1 100 0.1 1 10 100 REVERSE VOLTAGE, VOLTS 0.1 0.01 0.1 1 10.0 100 t, PULSE DURATION, sec.