UG30CPT

UG30APT THRU UG30DPT ULTRAFAST EFFICIENT PLASTIC RECTIFIER Reverse Voltage - 50 to 200 Volts TO-247AD 0.645 (16.4) 0.625 (15.9) 0.203 (5.16) 0.193 (4.90) 0.245 (6.2) 0.225 (5.7) 0.323 (8.2) 0.313 (7.9) 10o 30o 0.078 REF (1.98) Forward Current - 30.0 Amperes FEATURES ♦ Plastic package has Underwriters Laboratory Flammability Classification 94V-0 ♦ Ideally suited for use in very high frequency switching power supplies, inverters and as a free wheeling diodes ♦ Ultrafast, 15 nanosecond typical recovery time ♦ Low leakage current ♦ Glass passivated chip junctions ♦ Soft recovery characteristics ♦ Excellent high temperature switching ♦ High temperature soldering guaranteed: 250°C, 0.16” (4.06mm) from case for 10 seconds 0.170 (4.3) 0.840 (21.3) 0.820 (20.8) 10o TYP. BOTH SIDES 0.142 (3.6) 0.138 (3.5) 1 2 3 0.086 (2.18) 0.076 (1.93) 1o REF. BOTH SIDES 0.118 (3.0) 0.108 (2.7) 0.127 (3.22) 0.160 (4.1) 0.140 (3.5) 0.795 (20.2) 0.775 (19.6) 0.117 (2.97) MECHANICAL DATA 0.048 (1.22) 0.225 (5.7) 0.205 (5.2) 0.044 (1.12) 0.030 (0.76) 0.020 (0.51) PIN 2 CASE PIN 1 PIN 3 Dimensions in inches and (millimeters) Case: JEDEC TO-247AD molded plastic body over passivated chips Terminals: Plated leads solderable per MIL-STD-750, Method 2026 Polarity: As marked Mounting Position: Any Weight: 2.2 ounces, 6.3 grams MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25°C ambient temperature unless otherwise specified. SYMBOLS UG30APT UG30BPT UG30CPT UG30DPT UNITS Maximum repetitive peak reverse voltage Maximum RMS voltage Maximum DC blocking voltage Maximum average forward rectified current at TC=120°C Peak forward surge current 8.3 ms single half sine-wave superimposed on rated load (JEDEC Method) at TC=120°C Maximum instantaneous forward voltage per leg at 15A 30A 10A TJ=100°C Maximum DC reverse current at rated DC blocking voltage per leg Maximum reverse recovery time (NOTE 1) Maximum reverse recovery time (NOTE 2) VRRM VRMS VDC I(AV) IFSM 50 35 50 100 70 100 30.0 300.0 150 105 150 200 140 200 Volts Volts Volts Amps Amps VF TA =25°C TA =100°C TJ= 25°C TJ=100°C TJ=25°C TJ=100°C 1.0 1.15 0.85 5.0 800.0 20.0 35.0 50.0 22.0 50.0 70.0 2.0 -65 to +150 Volts IR trr trr Qrr CJ RΘJC TJ, TSTG µA ns ns nC pF °C/W °C Maximum recovered stored charge (NOTE 2) Typical junction capacitance (NOTE 3) Typical thermal resistance (NOTE 4) Operating and storage temperature range NOTES: (1) Reverse recovery test conditions: IF=0.5A, IR =1.0A, Irr=0.25A (2) trr and Qrr measured at: IF=15A VR=30V, di/dt=50 A/µs, IRR=10% IRM for measurement of trr (3) Measured at 1.0 MHZ and applied reverse voltage of 4.0 Volts (4) Thermal resistance from junction to case per leg mounted on heatsink 4/98 RATINGS AND CHARACTERISTIC CURVES UG30APT THRU UG30DPT FIG. 1 - FORWARD CURRENT DERATING CURVE FIG. 2 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT PER LEG 36 AVERAGE FORWARD CURRENT, AMPERES 1,000 RESISTIVE OR INDUCTIVE LOAD 24 18 12 6 0 PEAK FORWARD SURGE CURRENT, AMPERES 30 TC=120°C 8.3ms SINGLE HALF SINE-WAVE (JEDEC Method) 100 0 25 50 75 100 125 150 175 10 1 10 NUMBER OF CYCLES AT 60 HZ CASE TEMPERATURE, °C 100 INSTANTANEOUS REVERSE LEAKAGE CURRENT, MICROAMPERES FIG. 3 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS PER LEG INSTANTANEOUS FORWARD CURRENT, AMPERES FIG. 4 - TYPICAL REVERSE CHARACTERISTICS PER LEG 100 1,000 TJ=100°C 100 10 TJ=25°C PULSE WIDTH=300µs 1% DUTY CYCLE 10 TJ=25°C 1 1 0.1 0.1 0.01 0.4 0.6 0.8 1.0 1.2 1.4 1.6 0.01 0 20 40 60 80 100 INSTANTANEOUS FORWARD VOLTAGE, VOLTS PERCENT OF RATED PEAK REVERSE VOLTAGE, % RECOVERED STORED CHARGE/REVERSE RECOVERY TIME, nC/ns FIG. 5 - REVERSE SWITCHING CHARACTERISTICS PER LEG FIG. 6 - TYPICAL JUNCTION CAPACITANCE PER LEG 60 50 40 30 20 10 0 IF=15A VR=30V 100 di/dt=100 A/µs di/dt=50 A/µs di/dt=100 A/µs di/dt=150 A/µs di/dt=50 A/µs di/dt=20 A/µs JUNCTION CAPACITANCE, pF di/dt=150 A/µs di/dt=20 A/µs TJ=125°C f=1.0 MHz Vsig=50mVp-p 10 trr Qrr 0 25 50 75 100 125 150 175 1 0.1 1 10 100 JUNCTION TEMPERATURE, °C REVERSE VOLTAGE, VOLTS