UGB10DCT

NEW PRODUCT NEW PRODUCT NEW PRODUCT UGB10ACT THRU UGB10DCT ULTRAFAST SOFT RECOVERY RECTIFIER Reverse Voltage - 50 to 200 Volts Forward Current - 10.0 Amperes TO-263AB 0.380 (9.65) 0.420 (10.67) 0.245 (6.22) MIN K 0.047 (1.19) 0.055 (1.40) 0.160 (4.06) 0.190 (4.83) 0.045 (1.14) 0.055 (1.40) FEATURES ♦ Plastic package has Underwriters Laboratories Flammability Classification 94V-0 ♦ Ideally suited for free wheeling diode power factor correction applications ♦ Soft recovery characteristics ♦ Excellent high temperature switching ♦ Optimized to reduce switching losses ♦ High temperature soldering in accordance with CECC 802 / Reflow guaranteed ♦ Glass passivated chip junction 0.320 (8.13) 0.360 (9.14) 1 K 2 0.575 (14.60) 0.625 (15.88) SEATING PLATE -T- 0.090 (2.29) 0.110 (2.79) 0.018 (0.46) 0.025 (0.64) 0.027 (0.686) 0.037 (0.940) 0.080 (2.03) 0.110 (2.79) 0.095 (2.41) 0.100 (2.54) MECHANICAL DATA Case: JEDEC TO-263AB molded plastic body Terminals: Plated leads, solderable per MIL-STD-750, Method 2026 Polarity: As marked Mounting Position: Any Mounting Torque: 5 in. - lbs. max. Weight: 0.08 ounce, 2.24 grams PIN 1 K - HEATSINK PIN 2 Dimensions in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25°C ambient temperature unless otherwise specified. SYMBOLS UGB10ACT UGB10BCT UGB10CCT UGB10DCT UNITS Maximum repetitive peak reverse voltage Working peak reverse voltage Maximum RMS voltage Maximum DC blocking voltage Maximum average forward rectified current at TC=100°C Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC Method) per leg Maximum instantaneous forward voltage per leg at IF=10A, IF=5A, IF=5A, Maximum reverse leakage current per leg at working peak reverse voltage Maximum reverse recovery time per leg at IF=1.0A, di/dt=100A/µs, VR=30V, Irr=0.1 IRM Maximum reverse recovery time per leg at IF=0.5A, IR=1.0A, Irr=0.25A Maximum reverse recovery current per leg at IF=5A, di/dt=50A/µs,VR=30V Maximum stored charge per leg IF=2A, di/dt=20A/µs, VR=30V Irr=0.1 IRM Typical thermal resistance from junction to case per leg Operating junction and storage temperature range Maximum Typical Maximum Typical TJ=25°C TJ=25°C TJ=150°C TJ=25°C TJ=100°C VRRM VRWM VRMS VDC I(AV) IFSM 50 50 35 50 100 100 70 100 10 60 1.25 1.10 0.895 10 200 25 25 15 0.7 5.5 4.5 4.5 150 150 105 150 200 200 140 200 Volts Volts Volts Volts Amps Amps VF Volts µA ns ns Amps nC °C/W °C IR trr trr IRM Qrr RΘJC TJ, TSTG -40 to +150 4/98 RATINGS AND CHARACTERISTIC CURVES UGB10ACT THRU UGB10DCT FIG. 1 -FORWARD CURRENT DERATING CURVE AVERAGE FORWARD CURRENT, AMPERES FIG. 2 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT PER LEG 15 10 PEAK FORWARD SURGE CURRENT, AMPERES RESISTIVE OR INDUCTIVE LOAD 100 8.3ms SINGLE HALF SINE-WAVE (JEDEC Method) TC=105°C 10 5 0 1 0 25 50 75 100 125 CASE TEMPERATURE, °C 150 1 10 NUMBER OF CYCLES AT 60 HZ 100 FIG. 3 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS PER LEG 100 INSTANTANEOUS REVERSE LEAKAGE CURRENT, MICROAMPERES TJ=25°C PULSE WIDTH=300µs 1% DUTY CYCLE FIG. 4 - TYPICAL REVERSE CHARACTERISTICS PER LEG 1,000 TJ=125°C INSTANTANEOUS FORWARD CURRENT, AMPERES 10 TJ=125°C TJ=100°C TJ=100°C 100 1 10 TJ=25°C 1 TJ=25°C 0.1 0.1 0.01 0.2 0.4 0.6 0.8 1.0 1.2 1.4 20 40 60 80 100 PERCENT OF RATED PEAK REVERSE VOLTAGE, % INSTANTANEOUS FORWARD VOLTAGE, VOLTS FIG. 5 - REVERSE SWITCHING CHARACTERISTICS PER LEG FIG. 6 - TYPICAL JUNCTION CAPACITANCE PER LEG STORED CHARGE/REVERSE RECOVERY TIME, nC/ns 50 @2A, 20A/µs 100 TJ=125°C f=1.0 MHz Vsig=50MVp-p 40 30 @1A, 100A/µs CAPACITANCE, pF trr Qrr @5A, 50A/µs 10 20 @5A, 50A/µs @1A, 100A/µs @2A, 20A/µs 10 0 25 50 75 100 JUNCTION TEMPERATURE, °C 125 1 0.1 1 10 REVERSE VOLTAGE, VOLTS 100