UGF10DCT

NEW PRODUCT NEW PRODUCT NEW PRODUCT UGF10ACT THRU UGF10DCT ULTRAFAST SOFT RECOVERY RECTIFIER Reverse Voltage - 50 to 200 Volts ITO-220AB 0.405 (10.27) 0.383 (9.72) 0.188 (4.77) 0.172 (4.36) 0.110 (2.80) 0.100 (2.54) 0.140 (3.56) DIA. 0.130 (3.30) 0.131 (3.39) DIA 0.122 (3.08) Forward Current - 10.0 Amperes FEATURES ♦ Plastic package has Underwriters Laboratories Flammability Classification 94V-0 ♦ Ideally suited for free wheeling diode power factor correction applications ♦ Soft recovery characteristics ♦ Excellent high temperature switching ♦ Optimized to reduce switching losses ♦ High temperature soldering guaranteed: 250°C/10 seconds at terminals ♦ Glass passivated chip junction 0.600 (15.5) 0.580 (14.5) PIN 1 2 3 0.670 (17.2) 0.646 (16.4) 0.350 (8.89) 0.330 (8.38) 0.191 (4.85) 0.171 (4.35) 0.560 (14.22) 0.530 (13.46) 0.060 (1.52) 0.110 (2.80) 0.100 (2.54) MECHANICAL DATA Case: JEDEC ITO-220AB molded plastic body Terminals: Plated leads, solderable per MIL-STD-750, Method 2026 Polarity: As marked Mounting Position: Any Mounting Torque: 5 in. - lbs. max. Weight: 0.08 ounce, 2.24 grams 0.037 (0.94) 0.027 (0.69) 0.105 (2.67) 0.095 (2.41) 0.022 (0.55) 0.014 (0.36) PIN 1 PIN 3 PIN 2 0.205 (5.20) 0.195 (4.95) Dimensions in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25°C ambient temperature unless otherwise specified. SYMBOLS UGF10ACT UGF10BCT UGF10CCT UGF10DCT UNITS Maximum repetitive peak reverse voltage Working peak reverse voltage Maximum RMS voltage Maximum DC blocking voltage Maximum average forward rectified current at TC=100°C Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC Method) per leg Maximum instantaneous forward voltage per leg at IF=10A, IF=5A, IF=5A, Maximum reverse leakage current per leg at working peak reverse voltage Maximum reverse recovery time per leg at IF=1.0A, di/dt=100A/µs, VR=30V, Irr=0.1 IRM Maximum reverse recovery time per leg at IF=0.5A, IR=1.0A, Irr=0.25A Maximum reverse recovery current per leg at IF=5A, di/dt=50A/µs,VR=30V Maximum stored charge per leg IF=2A, di/dt=20A/µs, VR=30V Irr=0.1 IRM Typical thermal resistance from junction to case per leg Operating junction and storage temperature range NOTICE: Advanced product information is subject to change without notice VRRM VRWM VRMS VDC I(AV) IFSM TJ=25°C TJ=25°C TJ=150°C TJ=25°C TJ=100°C 50 50 35 100 100 100 70 100 10 60 1.25 1.10 0.895 10 200 25 25 15 0.7 5.5 4.5 6.0 150 150 105 200 200 200 140 200 Volts Volts Volts Volts Amps Amps VF Volts µA ns ns Amps nC °C/W °C IR trr Maximum Typical trr IRM Maximum Typical Qrr RΘJC TJ, TSTG -40 to +150 4/98 RATINGS AND CHARACTERISTIC CURVES UGF10ACT THRU UGF10DCT FIG. 1 -FORWARD CURRENT DERATING CURVE AVERAGE FORWARD CURRENT, AMPERES FIG. 2 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT PER LEG 15 RESISTIVE OR INDUCTIVE LOAD 100 PEAK FORWARD SURGE CURRENT, AMPERES 8.3ms SINGLE HALF SINE-WAVE (JEDEC Method) TC=105°C 10 10 5 0 1 0 25 50 75 100 125 150 CASE TEMPERATURE, °C 1 10 NUMBER OF CYCLES AT 60 HZ 100 FIG. 3 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS PER LEG 100 TJ=25°C PULSE WIDTH=300µs 1% DUTY CYCLE FIG. 4 - TYPICAL REVERSE CHARACTERISTICS PER LEG 1,000 INSTANTANEOUS REVERSE LEAKAGE CURRENT, MICROAMPERES TJ=125°C INSTANTANEOUS FORWARD CURRENT, AMPERES 10 TJ=125°C TJ=100°C TJ=100°C 100 1 10 TJ=25°C 1 TJ=25°C 0.1 0.1 0.01 0.2 0.4 0.6 0.8 1.0 1.2 1.4 20 40 60 80 100 PERCENT OF RATED PEAK REVERSE VOLTAGE, % INSTANTANEOUS FORWARD VOLTAGE, VOLTS FIG. 5 - REVERSE SWITCHING CHARACTERISTICS PER LEG FIG. 6 - TYPICAL JUNCTION CAPACITANCE PER LEG STORED CHARGE/REVERSE RECOVERY TIME, nC/ns 50 @2A, 20A/µs 100 TJ=125°C f=1.0 MHz Vsig=50MVp-p 40 CAPACITANCE, pF @5A, 50A/µs 30 @1A, 100A/µs 10 20 @5A, 50A/µs @1A, 100A/µs @2A, 20A/µs trr Qrr 10 0 25 100 75 50 JUNCTION TEMPERATURE, °C 125 1 0.1 1 10 REVERSE VOLTAGE, VOLTS 100