GHB-PLCC-CW2

55 Commerce Way Woburn, MA 01801 (781) 935 - 4442 (781) 938 - 5867 www.gilway.com GHB-PLCC-CW2 2.80 (0.110) 1.90 (0.073) 0.05 (0.002) 0.80 (0.031) Description This family of SMT LEDs is packaged in the industry standard PLCC-2 package. These SMT LEDs have high reliability performance and are designed to work under a wide range of environmental conditions. This high reliability feature makes them ideally suited to be used under harsh interior automotive as well as interior signs application conditions. To facilitate easy pick & place assembly, the LEDs are packed in EIA-compliant tape and reel. Every reel will be shipped in single intensity and color bin. These LEDs are compatible with IR solder reflow process. The super wide viewing angle at 120 ° makes these LEDs ideally suited for panel, push button, or general backlighting in automotive interior, office quipment, industrial equipment, and home appliances. 2.20 (0.087) 3.20 (0.126) 3.50 (0.138) 0.80 (0.031) CATHODE MARKING NOTE: ALL DIMENSIONS IN MILLIMETERS (INCHES). Device Selection Guide Color White Part Number GHB-PLCC-CW2 Min. I v @ 20 mA 100 Typical Iv @ 20 mA 300 Note: 1. The luminous intensity I v , is measured at the mechanical axis of the lamp package. The actual peak of the spatial radiation pattern may not be aligned with this axis. Absolute Maximum Ratings at T A = 25ûC Parameters DC Forward Current Peak Forward Current Power Dissipation Reverse Voltage Junction Temperature Operating Temperature Storage Temperature Notes: 1. Derate linearly as shown in Figure 5. 2. Duty factor = 10%, frequency = 1 kHz. [1] [2] InGaN 30 mA 90 mA 114 W 5V 110ûC Ð55ûC to +100ûC Ð55ûC to +100ûC Electrical Characteristics at T Color White A = 25ûC Reverse Voltage, V @ 10mA R Min. 5 Thermal Resistance R qJP (°C/W) 280 Forward Voltage, V F (Volts) @ I = 20 mA F Typ. Max. 3.5 4.3 Optical Characteristics at T A = 25ûC Viewing Angle 2 q1/2[2] (degrees) Typ. 120 Luminous Efficacy hv[3] (lm/W) Typ. 260 Luminous Intensity/ Total Flux Iv(mcd)/Fv(mlm) Typ. 0.45 Color White Typical Chromaticity Coordinates [1] x y 0.31 0.31 Notes: 1. The chromaticity coordinates are derived from the CIE 1931 Chromaticity Diagram and represent the perceived color of the device. 2. q 1/2 is the off-axis angle where the luminous intensity is 1/2 the peak intensity. I 3. Radiant intensity, I e in watts/steradian, may be calculated from the equation I e = v /hv , where I v is the luminous intensity in candelas and the luminous efficacy in lumens/watt. h v is 1.0 FORWARD CURRENT Ð mA 35 30 25 20 15 10 5 0 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 RELATIVE INTENSITY 0.8 0.6 0.4 0.2 0 380 430 480 530 580 630 680 730 780 WAVELENGTH Ð nm FORWARD VOLTAGE Ð V 1.6 RELATIVE LUMINOUS INTENSITY (NORMALIZED AT 20 mA) 35 30 0.020 5 mA 0.015 Y-COORDINATES 1.4 1.2 CURRENT Ð mA 25 20 15 10 5 1.0 0.8 0.6 0.4 0.2 0 0 5 10 15 20 25 30 35 0.010 0.005 0 -0.005 30 mA -0.010 -0.003 -0.002 -0.001 20 mA 10 mA 0 0 20 40 60 80 100 120 0 0.001 0.002 0.003 DC FORWARD CURRENT Ð mA TEMPERATURE Ð ¡C X-COORDINATES 1.0 NORMALIZED INTENSITY 0.8 0.6 0.4 0.2 0 -90 -80 -70 -60 -50 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 ANGULAR DISPLACEMENT Ð DEGREES 20 SEC. MAX. TEMPERATURE 10-40 SEC. 240-245¡C 183¡C Ð6¡C/SEC. MAX. TEMPERATURE 240¡C MAX. 3¡C/SEC. MAX. 100-150¡C 3¡C/SEC. MAX. 120 SEC. MAX. 60-150 SEC. TIME PRE-HEAT 120-180¡C ABOVE 183¡C 2-3¡C/SEC. TIME 6¡C/SEC. MAX. Recommended reflow soldering profile Recommended wave soldering profile 4.50 1.50 2.60 SOLDER RESIST