280-030P3H44MEGG

SERIES 28 HiPer-D® Standard and High-Density Connectors 280-030P float mount pin connectors for blind mating, crimp termination 280-030P HiPer-D® pin connectors feature stainless steel float bushings for blind mating. Attach to panel with #4-40 screws (not supplied with connector). Crimp, rear-releaseable size #20 or #22 contacts. Intermateable with standard M24308-type D-Subminiature connectors, the HiPer-D® features a rugged machined aluminum shell, rubber seals and optional ground springs for improved resistance to electromagnetic interference. Threaded holes on the rear of the connector allow direct attachment of HiPer-D® EMI backshells. Contacts are packaged with connector. Terminate contacts with crimp tools purchased separately. Glass-reinforced thermoset epoxy insulators, copper alloy retention clips. Fluorosilicone face seal and rear grommet meet IP67 immersion requirement (mated). 1000 VAC, 5 Amps (#22) or 7.5 Amps (#20). B Ordering Information Sample Part Number 280-030P Basic Part Number 280-030P Shell SizeContact Arrangement See Shell Size - Contact Arrangements Table Shell Finish ME = Electroless Nickel (RoHS) JF = Cadmium with Yellow Chromate Z1 = Passivated Stainless Steel (RoHS) MT = Nickel-PTFE (RoHS) Z2 = Gold (RoHS) Ground Spring G = Supplied with EMI Ground Spring N = No Ground Spring Mating Hardware N = No Hardware (supplied with #8-32 tapped hole) B = Female Guide Bushings G = Male Guide Pins Shell Size - Contact Arrangements Shell SizeContact Arr. Contact Size and Qty #20 #22 Standard Density 1S9 9 2S15 15 3S25 25 4S37 37 5S50 50 Mating Hardware N No Hardware #8-32 tapped hole B Female Guide Bushings High Density B-14 1H15 15 2H26 26 3H44 44 4H62 62 5H78 78 6H104 104 G Male Guide Pins 6H104 MT N N Materials and Finishes Shell Aluminum alloy Contacts Copper alloy, 50 microin. gold plated Insulators Retention Clips Thermoset epoxy Copper alloy Grommet, Seal, O-ring Fluorosilicone rubber Hardware 300 series stainless steel Specifications Current Rating #22 5 AMPS, #20 7.5 AMPS Test Voltage 1000 VAC RMS Insulation Resistance 5000 megohms minimum Operating Temperature -65° C. to +200° C. Ingress Protection Shock Vibration, Random IP 67 300 g. 43.92 g. © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 28 HiPer-D Catalog Dimensions in Inches (millimeters) are subject to change without notice. SERIES 28 HiPer-D® Standard and High-Density Connectors 280-030P float mount pin connectors for blind mating, crimp termination 280-030P DIMENSIONS GUIDE PIN, GUIDE BUSHING, OR 8-32 UNC 2B .150 (3.81) MIN. DEEP 2PLCS .250 (6.35) .170 (4.32) REF R .134 (3.41) G .120 (3.05) D G SECTION G-G .040±.040 (1.02±1.02) DIAMETRAL FLOAT CONNECTOR FLOAT BUSHING 4-40 UNC-2B .150 MIN. DEEP TYP 2 PLCS .390±.005 (9.91±0.13) B E C C .094 (2.39) F .262±.003 (6.65±0.08) A .784 (19.92) Shell Size 1 2 3 4 5 6 in A mm in 50.44 58.78 72.49 88.95 86.56 88.95 .494 .494 .494 .494 .600 .662 B mm ± .015 ± 0.38 ± .015 ± 0.38 1.986 2.314 2.854 3.502 3.408 3.502 12.55 12.55 12.55 12.55 15.24 16.81 C Basic in D E mm in mm 18.44 26.77 40.49 56.95 54.33 57.71 .389 9.88 .389 9.88 .389 9.88 .389 9.88 .501 12.73 .563 14.30 in. mm ± .005 ± 0.13 ± .005 ± 0.13 .984 1.312 1.852 2.500 2.406 2.500 24.99 33.32 47.04 63.50 61.11 63.50 .726 1.054 1.594 2.242 2.139 2.272 F Basic in mm 1.636 1.964 2.504 3.152 3.058 3.152 41.55 49.89 63.60 80.06 77.67 80.06 NOTES 1. HiPer-D® connectors are available with a wide variety of materials and finishes. See About Series 28 HiPer-D® Shell Plating Options for additional choices . Glenair offers the industry’s widest selection of plating and material choices with no setup charge, no minimum order quantity and no schedule impact. 2. For panel cutout dimensions, refer to Panel Cutouts and Printed Circuit Board Footprints. 3. Connectors are supplied with crimp contacts per M39029. Contacts are not installed. Refer to HiPer-D® Contacts and Crimp Tools for contact part numbers, specifications, crimp tool information, and insertion/extraction tools. 4. HiPer-D® connectors meet the requirements of MIL-DTL-24308 and are intermateable with standard M24308-type D-Subminiature connectors with corresponding contact arrangements and type. 5. Additional electrical, mechanical and environmental specifications are listed in HiPer-D® Product Specification. © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 28 HiPer-D Catalog Dimensions in Inches (millimeters) are subject to change without notice. B-15 B