557T175M

MIL-C-24308 D-Subminiature 557-175 D-Subminiature G-Spring Solid Backshell 557 T 1 75 M 2 F 0 B 1 F 0 2 Basic Part No. Cable Entry Style T = Top Basic Part Number Finish Symbol (Page 3) Shell Size (Table I) Receptacle Mounting (Table II) F0 = Front Mounting R1-R9 = Rear Mounting E Typ. Cable Range Inner Support Ring Dash No. (Table III), N = No Support Ring F = Strain Relief, G = Gland Nut, D = Dual “G” Spring With Strain Relief 0 = Without EMI Gasket, 1 = With EMI Gasket Jackscrew Type (Page A-4) 1.00 (25.4) Max Typ. Style F Strain Relief 1.195 (30.4) ±.031 (.8) Typ. SHELL SIZES 1&2 #4-40 UNC (2 Places) Typ. Connector Retaining Spring RFI/EMI Gasket Optional .135 (3.4) Max F SHELL SIZES 3, 4, & G Typ. Shell Sizes 3, 4, & 5 = .300 (7.6) Shell Size 6 = .425 (10.8) A B C Style G Gland Nut D Style D Dual Spring Strain Relief © 2004 Glenair, Inc. CAGE Code 06324 Printed in U.S.A. GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912 www.glenair.com E-Mail: sales@glenair.com A-74 557-175 D-Subminiature G-Spring Solid Backshell TABLE I: SHELL SIZE & CONNECTOR INTERFACE DIMENSIONS Shell Size 1 2 3 4 5 6 Com’l Shell Size Ref E/09 A/15 B/25 C/37 D/50 F/104 A 1.241 1.569 2.116 2.757 2.663 2.757 (31.5) (39.9) (53.7) (70.0) (67.6) (70.0) .515 .515 .515 .515 .625 .688 B (13.0) (13.0) (13.0) (13.0) (15.9) (17.5) .258 .258 .258 .258 .313 .344 C (6.6) (6.6) (6.6) (6.6) (8.0) (8.7) ±.005 .984 1.312 1.852 2.500 2.406 2.500 D (.1) (25.0) (33.3) (47.0) (63.5) (61.1) (63.5) TABLE I (Continued): CABLE ENTRY & GLAND NUT Shell Size 1 2 3 4 5 6 Com’l Shell Size Ref E/09 A/15 B/25 C/37 D/50 F/104 E Max .843 (21.4) .968 (24.6) 1.156 (29.4) 1.156 (29.4) 1.218 (30.9) 1.468 (37.3) F Max .625 (15.9) .750 (19.1) 1.000 (25.4) 1.000 (25.4) 1.250 (31.8) 1.375 (34.9) Cable Range Min Max .125 (3.2) .250 (6.4) .156 (4.0) .375 (9.5) .280 (7.1) .500 (12.7) .280 (7.1) .500 (12.7) .375 (9.5) .625 (15.9) .625 (15.9) .875 (22.2) TABLE II: RECEPTACLE MOUNTING Dash No. R1 R2 R3 R4 R5 R6 R7 R8 F0 Panel Thickness .031 (.8) .047 (1.2) .062 (1.6) .093 (2.4) .104 (2.6) .125 (3.2) .156 (4.0) .135 (3.4) N/A G .247 .231 .216 .185 .174 .153 .125 .140 .305 (6.3) (5.9) (5.5) (4.7) (4.4) (3.9) (3.2) (3.6) (7.7) TABLE III: SUPPORT RING Dash No. 01 02 03 04 05 06 07 08 09 10 Inner Support I.D. O.D. .187 (4.7) .227 (5.8) .218 (5.5) .258 (6.6) .250 (6.4) .290 (7.4) .281 (7.1) .321 (8.2) .312 (7.9) .352 (8.9) .343 (8.7) .383 (9.7) .375 (9.5) .415 (10.5) .406 (10.3) .446 (11.3) .438 (11.1) .478 (12.1) .468 (11.9) .508 (12.9) 1. Metric dimensions (mm) are indicated in parentheses. 2. DO NOT USE CONNECTORS WITH FLOAT MOUNTINGS. 3. For front mount, mating connector must be mounted to panel using M24308/26 female screwlocks. For rear mount, use Glenair GK134. 4. For proper termination it is recommended that Glenair 469-001 shield support ring be used on all assemblies. Place ring over wire bundle and under shield, position under G-Spring. © 2004 Glenair, Inc. CAGE Code 06324 Printed in U.S.A. GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912 www.glenair.com E-Mail: sales@glenair.com A-75 MIL-C-24308 D-Subminiature