790-026PL-6P6MN

Series 79 Micro-Crimp Section E: Panel Mount Connectors, Crimp Termination PANEL RECEPtACLES WIth PIN CoNtACtS, CRIMP tERMINAtIoN, 790-026P 790-026P connectors are designed for rear-panel mounting and are supplied with conductive panel gaskets. These connectors feature machined aluminum shells, fluorosilicone face seals and wire grommets for environmental protection. Contacts are rear-release snap-in crimp type. Connectors are supplied with crimp contacts packaged separately. Size #23 signal pins accept up to #22 AWG wire. Size #16 contacts accept #16-18 AWG wire. Size #12 contacts accept #12-14 AWG wire. Size 12 and 16 cavities also accept coaxial contacts purchased separately. Attach optional shielding adapters (799-016) for EMI protection. 790-026P Part Number Rear Panel Mounted Receptacle with Pin Contacts L-6P6 Shell Size Insert Arr. See Table 1 for Available Insert Arrangements To order a connector without size #16 or #12 power pins, substitute “W” instead of “P” in the insert arrangement. Example: 36P2 is supplied with 2 power pins. 36W2 is supplied less the power pins. See Section B for coaxial contacts purchased separately. Sample Part Number HOW TO ORDER MT G Hardware Option Shell Finish Electroless Nickel 790-026P M general purpose applications 1000 Hour Grey™ maximum corrosion protection and durability (non-reflective grey) Nickel-PTFE MT No Hardware N Female Jackpost P Zinc-Nickel with Black Chromate tactical applications (non-reflective black) ZNU Guide Pin G Female Guide Socket S Additional shell finishes are listed on page C-9. SPECIFICATIONS Current Rating Dielectric Withstanding Voltage Insulation Resistance Operating Temperature Shock Vibration #23 5 AMPS, #16 13 A., #12 23 A. #23 500 VAC RMS, #12 and #16 1800 VAC RMS 5000 megohms minimum -65° C. to +150° C. 300 g. 37 g. Shell Contacts MATERIALS AND FINISHES Aluminum alloy Copper alloy, 50 microinches gold plated Liquid crystal polymer (LCP) Beryllium copper alloy Flourosilicone rubber 300 series stainless steel Fluorosilicone, conductive Printed in U.S.A. E-Mail: sales@glenair.com Insulators Retention Clips Interfacial Seal, Grommet Hardware Panel Gasket © 2009 Glenair, Inc. www.glenair.com Dimensions in inches (millimeters) and are subject to change without notice. CAGE Code 06324 GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912 Rev. 04-July-2009 E-1 Panel Mount A B C D E F G H INDEX Series 79 Micro-Crimp Section E: Panel Mount Connectors, Crimp Termination Table 1 Contact Arrangements CRoSS-SECtIoNAL vIEW oF 790-026P RETAINING CLIP FRONT INSULATOR REAR INSULATOR GROMMET POTTING WIRE (REF.) .195 (4.95) .025 (0.64) EMI GASKET INTERFACIAL SEAL PIN CONTACT Panel Mount A B C D E F G H INDEX INDEX Layout A-5 B-2P2 B-9 C-13 D-15 D-3P3 D-7P2 E-11P2 E-19 E-7P3 #23 #16 #12 5 2 9 13 15 3 5 9 19 4 3 2 2 Contact Quantity Face View GUIDE PIN SHELL .007 (0.18) TABLE 2 HARDWARE OPTION F-15P2 13 2 F-23 F-5P5 G-33 h-10P4 33 6 4 23 5 h-29P7 22 7 H-36P2 34 h-54P2 52 2 H-5P5 H-66 66 5 2 Connector is supplied with threaded holes. Shell sizes H and L have #6-32 threads, other sizes have #4-40 threads. Thread depth is .150" (3.8). No Mating Hardware N Connector is supplied with non-removable stainless steel jackposts. Shell sizes H and L have #4-40 UNC thread, other sizes have #2-56 thread. Stainless steel. Jackposts P J-17P4 13 4 J-25P2 23 2 J-33 J-7P7 33 7 Connector is supplied with stainless steel nonremovable guide pins. Mates with type "S" guide sockets on corresponding plug connector. Guide Pins G Connector is supplied with stainless steel nonremovable bushings. Mates with type "G" guide pins on corresponding plug connector. S Guide Sockets K-27P4 23 4 K-35P2 33 2 K-43 K-9P9 L-6P6 © 2009 Glenair, Inc. www.glenair.com 43 9 6 Dimensions in inches (millimeters) and are subject to change without notice. CAGE Code 06324 Printed in U.S.A. E-Mail: sales@glenair.com GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912 Rev. 04-July-2009 E-2 Series 79 Micro-Crimp Section E: Panel Mount Connectors, Crimp Termination 790-026P ShELL SIzE A,B,C,D,E,F,J,K DIMENSIoNS A MAX B BASIC C BASIC D MAX .308 (7.82) MAX BLIND MATE 2-56 UNC-2B X .150 (3.81) MIN 2 PLACES .170 (4.32) JACKPOST SHOWN FOR REFERENCE. SEE ORDERING INFORMATION FOR OTHER OPTIONS. .335 (8.51) MAX .640 (16.26) MAX SHELL SIZES A, B, C, D, E, F, G, J, k +/- .030 (0.76) ALLOWABLE MISALIGNMENT FROM CENTERLINE .093 ± .005 (2.36 ± 0.13) E MAX C BASIC .215 (5.46) MAX .485 (12.32) MAX 2-56 UNC-2B X .150 (3.81) MIN 2 PLACES 790-026P Dimensions for Size A-F, J and K Shell Size A B C D E F J K A Max. In. 1.211 1.361 1.511 1.611 1.761 1.911 2.261 2.661 B Basic In. .925 1.075 1.225 1.325 1.475 1.625 1.975 2.375 C Basic In. .565 .715 .865 .965 1.115 1.265 1.615 2.015 D Max. In. .401 .551 .701 .801 .951 1.101 1.460 1.860 E Max. In. .760 .910 1.060 1.160 1.310 1.460 1.810 2.210 mm. 30.76 34.57 38.38 40.92 44.73 48.54 57.43 67.59 mm. 23.50 27.31 31.12 33.66 37.47 41.28 50.17 60.33 mm. 14.35 18.16 21.97 24.51 28.32 32.13 41.02 51.18 mm. 10.19 14.00 17.81 20.35 24.16 27.96 37.08 47.24 mm. 19.30 21.11 26.92 29.46 33.27 37.08 45.97 56.13 © 2009 Glenair, Inc. www.glenair.com Dimensions in inches (millimeters) and are subject to change without notice. CAGE Code 06324 Printed in U.S.A. E-Mail: sales@glenair.com GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912 Rev. 04-July-2009 E-3 Panel Mount A B C D E F G H INDEX INDEX Series 79 Micro-Crimp Section E: Panel Mount Connectors, Crimp Termination 790-026P ShELL SIzE G DIMENSIoNS Panel Mount A 1.861 (47.27) MAX 1.575 (40.01) BASIC 1.215 (30.86) BASIC 1.079 (27.41) MAX .387 (9.83) MAX BLIND MATE B C D E .575 (14.61) MAX .170 (4.32) 2-56 UNC-2B X .150 (3.81) MIN 2 PLACES JACKPOST SHOWN FOR REFERENCE. SEE ORDERING INFORMATION FOR OTHER OPTIONS. .335 (8.51) MAX .640 (16.26) MAX SHELL SIZES A, B, C, D, E, F, G, J, k +/- .030 (0.76) ALLOWABLE MISALIGNMENT FROM CENTERLINE .093 ± .005 (2.36 ± 0.13) 1.410 (35.81) MAX 1.215 (30.86) BASIC .215 (5.46) MAX F G H INDEX INDEX © 2009 Glenair, Inc. www.glenair.com 2-56 UNC-2B X .150 (3.81) MIN 2 PLACES Dimensions in inches (millimeters) and are subject to change without notice. CAGE Code 06324 Printed in U.S.A. E-Mail: sales@glenair.com GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912 Rev. 04-July-2009 E-4 Series 79 Micro-Crimp Section E: Panel Mount Connectors, Crimp Termination 790-026P ShELL SIzE h AND L DIMENSIoNS F MAX G BASIC H BASIC J MAX .410 (10.41) MAX 4-40 UNC-2B X .150 (3.81) MIN 2 PLACES .170 (4.32) JACKPOST SHOWN FOR REFERENCE. SEE ORDERING INFORMATION FOR OTHER OPTIONS. .093 ± .005 (2.36 ± 0.13) .385 (9.78) MAX BLIND MATE .640 (16.26) MAX K MAX H BASIC .265 (6.73) MAX .600 (15.24) MAX 4-40 UNC-2B X .150 (3.81) MIN 2 PLACES SHELL SIZES H, L +/- .040 (1.02) ALLOWABLE MISALIGNMENT FROM CENTERLINE 790-026P SIzE h & L DIMENSIoNS Shell Size H L F Max. In. mm. 2.500 63.50 2.736 69.49 G Basic In. mm. 2.236 56.79 2.472 62.79 H Basic In. mm. 1.800 45.72 2.036 51.71 J Max. In. mm. 1.450 36.83 1.686 42.82 K Max. In. mm. 2.045 51.94 2.281 57.94 © 2009 Glenair, Inc. www.glenair.com Dimensions in inches (millimeters) and are subject to change without notice. CAGE Code 06324 Printed in U.S.A. E-Mail: sales@glenair.com GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912 Rev. 04-July-2009 E-5 Panel Mount A B C D E F G H INDEX INDEX