G697L250T1UF

Global Mixed-mode Technology Inc. G696/G697 Microprocessor Reset IC Features Precision Monitoring of +3V, +3.3V, and +5V Power-Supply Voltages General Description The G696/G697 are microprocessor (µP) supervisory circuits used to monitor the power supplies in µP and digital systems. They provide excellent circuit reliability and low cost and adjustments when used with +5V, +3.3V, +3.0V- powered circuits. These circuits perform a single function: they assert a reset signal whenever the VCC supply voltage declines below a preset threshold, with hysteresis keeping it asserted for time delay determined by externally programmable time delay generator after VCC has risen above the reset threshold. Reset thresholds suitable for operation with a variety of supply voltages are available. The G697L has an open-drain output stage, while the G696 have push-pull outputs. The G697L’s open-drain RESET output requires a pull-up resistor that can be connected to a voltage higher than VCC. The G696L have an active-low RESET output, while the G696H has an active-high RESET output. The reset comparator is designed to ignore fast transients on VCC, and the outputs are guaranteed to be in the correct logic state for VCC down to 0.8V. Fully Specified Over Temperature Available in Three Output Configurations Push-Pull RESET Output (G696L) Push-Pull RESET Output (G696H) Open-Drain RESET Output (G697L) Externally Programmable Time Delay Generator 14µA Supply Current Guaranteed Reset Valid to VCC = 0.8V Power Supply Transient Immunity 5 pin SOT-23-5 or TSOT-23-5 Packages 2% Threshold Accuracy Applications Computers Controllers Intelligent Instruments Critical µP and µC Power Monitoring Portable / Battery-Powered Equipment Automotive Low supply current makes the G696/G697 ideal for use in portable equipment. The G696/G697 are available in 5-pin SOT23-5 or TSOT-23-5 packages. Pin Configuration Typical Application Circuit VCC RESET RESET (RESET) 1 5 CD VCC Rpull-up* VCC VCC 2 G696/G697 G696/G697 CD RESET (RESET) GND CD µP RESET INPUT GND GND 3 4 NC SOT-23-5/TSOT-23-5 ()is for G696H *G697 ONLY Ver: 1.8 May 10, 2006 TEL: 886-3-5788833 http://www.gmt.com.tw 1 Global Mixed-mode Technology Inc. Ordering Information ORDER NUMBER G696HxxxT1U G696LxxxT1U G697LxxxT1U G696HxxxTOU G696LxxxTOU G697LxxxTOU G696/G697 PACKAGE SOT-23-5 SOT-23-5 SOT-23-5 TSOT-23-5 TSOT-23-5 TSOT-23-5 ORDER NUMBER (Pb free) G696HxxxT1Uf G696LxxxT1Uf G697LxxxT1Uf G696HxxxTOUf G696LxxxTOUf G697LxxxTOUf TEMP. RANGE -40°C ~ +105°C -40°C ~ +105°C -40°C ~ +105°C -40°C ~ +105°C -40°C ~ +105°C -40°C ~ +105°C Note: T1: SOT-23-5 TO: TSOT-23-5 U: Tape & Reel * xxx specifies the threshold voltage. e.g. 263 denotes the 2.64V threshold voltage. Selector Guide ORDER NUMBER G697L463T1U G697L438T1U G697L400T1U G697L330T1U G697L308T1U G697L293T1U G697L263T1U G697L250T1U G696H463T1U G696H438T1U G696H400T1U G696H330T1U G696H308T1U G696H293T1U G696H263T1U G696H250T1U G696L463T1U G696L438T1U G696L400T1U G696L330T1U G696L308T1U G696L293T1U G696L263T1U G696L250T1U T1: SOT-23-5 ORDER NUMBER (Pb free) G697L463T1Uf G697L438T1Uf G697L400T1Uf G697L330T1Uf G697L308T1Uf G697L293T1Uf G697L263T1Uf G697L250T1Uf G696H463T1Uf G696H438T1Uf G696H400T1Uf G696H330T1Uf G696H308T1Uf G696H293T1Uf G696H263T1Uf G696H250T1Uf G696L463T1Uf G696L438T1Uf G696L400T1Uf G696L330T1Uf G696L308T1Uf G696L293T1Uf G696L263T1Uf G696L250T1Uf RESET THRESHOLD (V) 4.60 4.32 3.96 3.30 3.10 2.91 2.64 2.50 4.60 4.32 3.96 3.30 3.10 2.91 2.64 2.50 4.60 4.32 3.96 3.30 3.10 2.91 2.64 2.50 OUTPUT TYPE Open-Drain RESET Open-Drain RESET Open-Drain RESET Open-Drain RESET Open-Drain RESET Open-Drain RESET Open-Drain RESET Open-Drain RESET Push-Pull RESET Push-Pull RESET Push-Pull RESET Push-Pull RESET Push-Pull RESET Push-Pull RESET Push-Pull RESET Push-Pull RESET Push-Pull RESET Push-Pull RESET Push-Pull RESET Push-Pull RESET Push-Pull RESET Push-Pull RESET Push-Pull RESET Push-Pull RESET TOP MARK 697Gx 697Fx 697Ex 697Dx 697Cx 697Bx 697Ax 697Hx 696Lx 696Kx 696Jx 696Nx 696Ix 696Hx 696Gx 696Qx 696Fx 696Ex 696Dx 696Mx 696Cx 696Bx 696Ax 696Px Ver: 1.8 May 10, 2006 TEL: 886-3-5788833 http://www.gmt.com.tw 2 Global Mixed-mode Technology Inc. Selector Guide ORDER NUMBER G697L463TOU G697L438TOU G697L400TOU G697L330TOU G697L308TOU G697L293TOU G697L263TOU G697L250TOU G696H463TOU G696H438TOU G696H400TOU G696H330TOU G696H308TOU G696H293TOU G696H263TOU G696H250TOU G696L463TOU G696L438TOU G696L400TOU G696L330TOU G696L308TOU G696L293TOU G696L263TOU G696L250TOU TO: TSOT-23-5 G696/G697 OUTPUT TYPE TOP MARK 697Gx 697Fx 697Ex 697Dx 697Cx 697Bx 697Ax 697Hx 696Lx 696Kx 696Jx 696Nx 696Ix 696Hx 696Gx 696Qx 696Fx 696Ex 696Dx 696Mx 696Cx 696Bx 696Ax 696Px ORDER NUMBER (Pb free) G697L463TOUf G697L438TOUf G697L400TOUf G697L330TOUf G697L308TOUf G697L293TOUf G697L263TOUf G697L250TOUf G696H463TOUf G696H438TOUf G696H400TOUf G696H330TOUf G696H308TOUf G696H293TOUf G696H263TOUf G696H250TOUf G696L463TOUf G696L438TOUf G696L400TOUf G696L330TOUf G696L308TOUf G696L293TOUf G696L263TOUf G696L250TOUf RESET THRESHOLD (V) 4.60 4.32 3.96 3.30 3.10 2.91 2.64 2.50 4.60 4.32 3.96 3.30 3.10 2.91 2.64 2.50 4.60 4.32 3.96 3.30 3.10 2.91 2.64 2.50 Open-Drain RESET Open-Drain RESET Open-Drain RESET Open-Drain RESET Open-Drain RESET Open-Drain RESET Open-Drain RESET Open-Drain RESET Push-Pull RESET Push-Pull RESET Push-Pull RESET Push-Pull RESET Push-Pull RESET Push-Pull RESET Push-Pull RESET Push-Pull RESET Push-Pull RESET Push-Pull RESET Push-Pull RESET Push-Pull RESET Push-Pull RESET Push-Pull RESET Push-Pull RESET Push-Pull RESET Ver: 1.8 May 10, 2006 TEL: 886-3-5788833 http://www.gmt.com.tw 3 Global Mixed-mode Technology Inc. Absolute Maximum Ratings Terminal Voltage (with respect to GND) VCC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to +6.0V Delay Capacitor Pin Voltage, VCD. . -0.3 to (VCC +0.3V) RESET, RESET (push-pull) . . . . .-0.3V to (VCC + 0.3V) RESET (open drain). . . . . . . . . . . . . . . -0.3V to +6.0V Input Current, VCC . . . . . . . . . . . . . . . . . . . . . . . 20mA G696/G697 Output Current, RESET, RESET . . . . . . . . . . . 20mA Operating Temperature Range. . . . . .-40°C to +105°C Storage Temperature Range . . . . . . .-65°C to +150°C Reflow Temperature (soldering, 10sec) . . . .. . . 260°C Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Electrical Characteristics (VCC = full range, TA = -40°C to +105°C, unless otherwise noted. Typical values are at TA = +25°C, VCC = 5V for 463/438/400/330 versions, VCC= 3.3V for 308/293 versions, and VCC = 3V for 263/250 version.) (Note 1) PARAMETER VCC Range Supply Current (SOT-23-5) ICC SYMBOL CONDITION TA = 0°C +70°C TA = -40°C +105°C VCC VTH, RESET deasserted rent (G697L) Note 1: Production testing done at TA = +25°C; limits over temperature guaranteed by design. Ver: 1.8 May 10, 2006 TEL: 886-3-5788833 http://www.gmt.com.tw 4 Global Mixed-mode Technology Inc. Typical Operating Characteristics G696/G697 (VCC = full range, TA = -40°C to +105°C, unless otherwise noted. Typical values are at TA = +25°C, VCC = 5V for 463/438/400/330 versions, VCC= 3.3V for 308/293 versions, and VCC = 3V for 263/250 version.) Supply Current vs. VCC 8 7 6 Supply Current (µA) Supply Current (µA) Supply Curremt vs. Temperature (No Load) 7 6 5 4 3 2 1 0 -40 V CC=2.5V V CC=5V V CC=3.3V 5 4 3 2 1 0 0 0.6 1 1.2 1.5 1.8 2.1 2.4 2.7 3 3.2 3.3 3.4 3.5 3.7 3.9 4 4.5 5 5.5 6 -20 0 VCC (V) 20 40 Temperature (°C) 60 80 Normalized Reset Threshold vs. Temperature 1.06 1.05 (V) I CD, CD D elay Pin Sink Current (mA) CD Delay Pin Sink Current vs. Voltage 40 35 1.04 1.03 1.02 1.01 1 0.99 0.98 0.97 0.96 -40 -30 -20 -10 0 10 V TH+ Normalized Ormalized VT H+ , V T H- 30 25 20 V CC=3V V T H- V CC=2.5V 15 10 5 0 V CC=1.5V 20 27 30 40 50 60 70 80 90 0.05 TA , Ambient Temperature ( °C) 0.2 0.4 0.6 1.2 1.8 V CD, Delay Pin Voltage (V) 2.4 3 Output Time Delay vs. Capacitance (VCC>VTH to output change) 10000 Output Time Delay vs. Capacitance (VCC