SSFP18N20

SSFP18N20 StarMOST Power MOSFET ■ ■ Extremely high dv/dt capability Low Gate Charge Qg results in Simple Drive Requirement 100% avalanche tested Gate charge minimized Very low intrinsic capacitances Very good manufacturing repeatability VDSS = 200V ID25 = 18A RDS(ON) = 0.18Ω ■ ■ ■ ■ Description StarMOS is a new generation of high voltage N–Channel enhancement mode power MOSFETs. This new technology minimises the JFET effect, increases packing density and reduces the on-resistance. StarMOS also achieves faster switching speeds through optimised gate layout with planar stripe DMOS technology. Pin1–Gate Pin2–Drain Pin1–Source Application ■ Switching application Absolute Maximum Ratings Parameter ID@Tc=25ْ C ID@Tc=100ْC IDM PD@TC=25ْC VGS EAS IAR EAR dv/dt TJ TSTG Continuous Drain Current,VGS@10V Continuous Drain Current,VGS@10V Pulsed Drain Current Power Dissipation Linear Derating Factor Gate-to-Source Voltage Single Pulse Avalanche Energy Avalanche Current ① ① ③ ② ① Max. 18 11.4 72 139 1.2 ±30 216 18 13.9 5.0 –55 to +150 300(1.6mm from case) 10 Ibf in(1.1N m) ● ● Units A W W/ْ C V mJ A mJ V/ns ْC Repetitive Avalanche Energy Peak Diode Recovery dv/dt Operating Junction and Storage Temperature Range Soldering Temperature, for 10 seconds Mounting Torque,6-32 or M3 screw Thermal Resistance Parameter RθJC RθCS RθJA Junction-to-case Case-to-Sink,Flat,Greased Surface Junction-to-Ambient Min. — — — Typ. — 0.5 — Max. 0.9 — 62.5 ْC/W Units 1 SSFP18N20 StarMOST Power MOSFET Electrical Characteristics @TJ=25 ْC(unless otherwise specified) Parameter V(BR)DSS RDS(on) VGS(th) gfs IDSS IGSS Qg Qgs Qgd td(on) tr td(off) tf LD Drain-to-Source Breakdown Voltage Static Drain-to-Source On-resistance Gate Threshold Voltage Forward Transconductance Drain-to-Source Leakage current Gate-to-Source Forward leakage Gate-to-Source Reverse leakage Total Gate Charge Gate-to-Source charge Gate-to-Drain("Miller") charge Turn-on Delay Time Rise Time Turn-Off Delay Time Fall Time Internal Drain Inductance △V(BR)DSS/△TJ Breakdown Voltage Temp.Coefficient Min. 200 — — 2.0 — — — — — — — — — — — — — Typ. — 0.26 — — 9.61 — — — — 44 10.4 27.1 17 16 48 24 5.0 Max. Units — — 0.18 4.0 — 10 100 100 -100 58 — — 40 40 110 60 — V Test Conditions VGS=0V,ID=250μA ④ V/ْC Reference to 25ْC,ID=1mA Ω VGS=10V,ID=9A V S μA nA VDS=40V,ID=9A VDS=200V,VGS=0V VDS=160V,VGS=0V,TJ=150ْC VGS=30V VGS=-30V VDS=VGS,ID=250μA ID=18A nC VDS=160V VGS=10V VDD=100V ID=18A nS RG=9.1Ω Between lead, 6mm(0.25in.) nH from package and center of die contact VGS=0V pF VDS=25V f=1.0MHZ LS Ciss Coss Crss Internal Source Inductance Input Capacitance Output Capacitance Reverse Transfer Capacitance — — — — 13 1300 400 130 — — — — Source-Drain Ratings and Characteristics Parameter IS ISM VSD trr Qrr ton Continuous Source Current (Body Diode) Pulsed Source Current (Body Diode) ① Diode Forward Voltage Reverse Recovery Time Reverse Recovery Charge Forward Turn-on Time . . Min. — — — — — Typ. — — — 195 1.35 Max. 18 A 72 1.5 — — V nS μC Units Test Conditions MOSFET symbol showing the integral reverse p-n junction diode. TJ=25ْC,IS=18A,VGS=0V ④ TJ=25ْC,IF=18A di/dt=100A/μs ④ Intrinsic turn-on time is negligible (turn-on is dominated by Ls + LD) Notes: ① Repetitive rating;pulse width limited by max.junction temperature(see figure 11) ③ ISD≤18A,di/dt≤260A/μS,VDD≤V(BR)DSS, TJ≤25ْ C ④ Pulse width≤300μS; duty cycle≤2% ② L = 1mH, IAS = 18 A, VDD = 50V, RG = 27Ω, Starting TJ = 25°C 2