ISC15ANP4

LCD Switches Programmable OLED Video Switch and Display DISTINCTIVE CHARACTERISTICS IS Series • • • • • • • • • Organic LED technology Range of 65,536 colors in 16 bit mode, 256 colors in 8 bit mode Full viewing angle of 180° Exceptional contrast and brightness: 50 times greater bright ness than previous LCD products, four times more enhanced resolution High resolution provides sharp, clear images of ver y small characters Operated by commands and data supplied via SPI communications protocol Distinct, long travel of 4.5mm (same as KP01 Series) Dust tight construction Sophisticated housing based on black color Viewing area: 15.5mm x 11.6mm (horizontal x vertical) High reliability and long life of three million actuations minimum High resolution of 64RGB x 48 pixels Epoxy Sealed Straight PC Terminals Snap-in Stando for Easy, Secure Mounting and Alignment Viewing area: 12.9mm x 9.9mm (horizontal x vertical) High resolution of 52RGB x 36 pixels Crimped terminals ensure secure PC mounting and prevent dislodging during wave soldering APPLICATIONS Actual Sizes The OLED SMARTSWITCH Series complements multiple applications, including: TM • Broadcast equipment • Education equipment • Audio equipment • Image equipment • Vending machines • POS • Automation control equipment sales@greatecs.com www.greatecs.com 1 LCD Switches Programmable OLED Video Switch and Display SMARTSWITCH PART NUMBER & DESCRIPTION Part Number ISC15ANP4 Switch Description SPST Momentary ON Gold Contacts Straight PC Terminals OLED Color OLED Display Module 65,536 Colors Pixel Format 64RGB x 48 Pixels Horizontal x Vertical IS Series SMARTSWITCH SPECFICATIONS Circuit Contact Position Electrical Capacity (Resistive Load) Contact Resistance Insulation Resistance Dielectric Strength Mechanical Endurance Electrical Endurance Operating Force Total Travel SPST normally open Leave actuator: 1 – 2 OFF Push actuator: 1 – 2 ON 100mA @ 12V DC 200 milliohms maximum @ 20mV 10mA 100 megohms minimum @ 100V DC 125V AC for 1 minute minimum 3,000,000 operations minimum 3,000,000 operations minimum 2.0 ± 0.5 Newtons 4.5mm (.177”) SMARTSWITCH OLED SPECFICATIONS Characteristics of Display Display Device Display Mode Viewing Area Pixel Format Pixel Size Interface Number of Colors Operating Temperature Range Storage Temperature Range Operating Life Time (Display) Color OLED display module Passive matrix 15.5mm x 11.6mm (horizontal x vertical) 64RGB x 48 pixels (horizontal x vertical) 0.21mm x 0.20mm (horizontal x vertical) Serial (SPI) interface 65,536 Colors (16bit: R 5bit/G 6bit/B 5bit) or 256 Colors (8bit: R 2bit/G 3bit/B 3bit) –20°C ~ +70°C (–4°F ~ +158°F) –30°C ~ +80°C (–22°F ~ +176°F) 15,000 hours (at 40% duty) Absolute Maximum Ratings Items Supply Voltage for Logic/Interface Supply Voltage for Drive Input Voltage Symbols V DD V CC VI Ratings –0.3V to +4.0V –0.3V to +19.0V –0.3V to V D D +0.3V Recommended Operating Conditions Items Supply Voltage for Logic/Interface Supply Voltage for Drive Input High Level Voltage Input Low Level Voltage Symbols Minimum V DD V CC V IH V IL 2.4V 15.0V 0.8 x V –– DD Typical 2.8V 16.0V –– –– Maximum 3.5V 17.0V –– 0.2V x V DD Current Consumption (Temperature at 25°C, V Items All-Pixels-On Mode *Drive System Power Current All-Pixels-On Mode *Logic/IF System Power Current Sleep Mode **Drive System Power Current Sleep Mode **Logic/IF System Power Current DD = 2.8V, V CC = 16.0V) Max 7.0mA 0.2mA 10 A 10 A Optical Characteristics (Temperature at 25°C, Initial Value: 87 x 0F) Items Luminosity White Color Coordinate Red Color Coordinate Green Color Coordinate Blue Color Coordinate Contrast Ratio (x) (y) (x) (y) (x) (y) (x) (y) Min 75 0.29 0.30 0.60 0.31 0.26 0.59 0.10 0.12 100 Typical 100 0.31 0.35 0.64 0.35 0.30 0.63 0.14 0.18 –– Max 125 0.35 0.40 0.68 0.39 0.34 0.67 0.18 0.24 –– Unit cd/m 2 –– –– –– –– –– –– –– –– –– Remarks White (All pixels on) Symbols Min Typical I CC1 I DD1 I CC2 I DD2 –– 5.5mA –– 0.16mA –– –– –– –– * All pixels shall be turned on with the maximum level gray scale ** All pixels shall be turned o (while chip is operating) sales@greatecs.com www.greatecs.com 2 LCD Switches Programmable OLED Video Switch and Display SMARTSWITCH BLOCK DIAGRAM & PIN CONFIGURATIONS IS Series Color OLED Panel 64RGB x 48 SR1,SG1,SB1......SR64, SG64,SB64 COM1....COM48 Segment Driver Common Driver OLED Driver with Controller VDD VCC 3 9 SEG/COM Driving Block Gray Scale Decoder RES SCK SS SDI D/C 5 7 4 8 6 MCU Interface Command Decoder Graphic Display Data RAM 96 x 64 x 16 Bit Oscillator Display Timing Generator GND 10 SW 1 2 SW ISC15ANP4 Pin No. 1 2 3 4 5 6 7 8 9 10 Symbol SW SW V DD SS RES D/C SCK SDI VCC GND Name Terminal of Switch Terminal of Switch Power Slave Select Reset Data/Command Serial Clock Serial Data In Power Ground Function Normally open Normally open Power source for logic circuit Slave select for SPI. This line is active low. Reset signal input. When pin is low, initialization of chip is executed Data/Command Control. When pin is pulled low, data will be interpreted as Command; when pulled high, data will be interpreted as Data. Clock line for SPI that synchronizes command and data Data input line for SPI Power source for drive OLED Connect to ground SMARTSWITCH TYPICAL DIMENSIONS Terminal numbers are not on the switch. See Pixel Detail (13.41) .528 (3.3) .130 (0.6) Typ .024 (11.6) .457 2 Stando 1 (18.0) .709 Stando 2 (1.0)Typ .039 10 9 (20.59) .811 (9.57) .377 (0.74) .029 (15.5) .610 (23.13) .911 (0.4) Typ .016 See Standoff Detail (23.0) .906 (3.4) .134 (16.0) .630 (7.62) .300 1 4 (7.0) .276 3 Stando 2 (0.3) Typ .012 (8.0) .315 (7.05) .278 (18.0) .709 (0.2) Typ .008 (2.0) .079 Stando 1 Pixel Detail (0.21)Typ .0083 (0.02) Typ .0008 Pixel Detail A (0.20) .0079 (0.17 ) .0067 (0.04) Typ .0016 (0.07) Typ .0028 Stando Detail (0.2) .008 A (1.25) .049 Footprint (1.0)Typ .039 (7.0) .276 8x (0.75) Dia .029 (2.0) .079 9 10 2x (0.9) Dia .035 (0.20) Typ .0079 R RGBR 2 (0.02) Typ .0008 See Pixel Detail A (0.21) .0083 Dimension A Stando 2 = (2.3) Stando 1 = (2.7) .091 .106 (2.0) Dia .079 3 4 (7.62) .300 1 (16.0) .630 (7.05) .278 (8.0) .315 4x (1.3) Di a .051 Landless sales@greatecs.com www.greatecs.com 3 LCD Switches Programmable OLED Video Switch and Display SMARTSWITCH PART NUMBER & DESCRIPTION Part Number ISC01P Display Description Straight PC Terminals OLED Color OLED Display Module 65,536 Colors Pixel Format 52RGB x 36 Pixels Horizontal x Vertical IS Series SMARTSWITCH LCD SPECFICATIONS Characteristics of Display Display Device Display Mode Viewing Area Pixel Format Pixel Size Interface Number of Colors Operating Temperature Range Storage Temperature Range Operating Life Time (Display) Color OLED display module Passive matrix 12.9mm x 9.9mm (horizontal x vertical) 52RGB x 36 pixels (horizontal x vertical) 0.21mm x 0.22mm (horizontal x vertical) Serial (SPI) interface 65,536 Colors (16bit: B 5bit/G 6bit/R 5bit) or 256 Colors (8bit: B 3bit/G 3bit/R 2bit) –20°C ~ +70°C (–4°F ~ +158°F) –30°C ~ +80°C (–22°F ~ +176°F) 15,000 hours (40% pixels ON) Absolute Maximum Ratings Items Supply Voltage for Logic/Interface Supply Voltage for Drive Input Voltage Symbols V DD V CC VI Ratings –0.3V to +4.0V 0.3V to +19.0V –0.3V to V +0.3V Absolute Maximum Ratings Items Supply Voltage for Logic/Interface Supply Voltage for Drive Input High Level Voltage Input Low Level Voltage Symbols Minimum V DD V CC VIH V IL 2.4V 15.0V 0.8 x V –– DD Typical 2.8V 16.0V –– –– Maximum 3.5V 17.0V –– 0.2V x V DD DD Current Consumption (Temperature at 25°C, V Items All-Pixels-On Mode *Drive System Power Current All-Pixels-On Mode *Logic/IF System Power Current Sleep Mode **Drive System Power Current Sleep Mode **Logic/IF System Power Current DD = 2.8V, V CC = 16.0V) Max 4.5mA Optical Characteristics (Temperature at 25°C, Initial Value: 87 x 0F) Items Luminosity White Color Coordinate Red Color Coordinate Green Color Coordinate Blue Color Coordinate Contrast Ratio (x) (y) (x) (y) (x) (y) (x) (y) Min 75 0.29 0.30 0.60 0.31 0.26 0.59 0.10 0.12 100 Typical 100 0.31 0.35 0.64 0.35 0.30 0.63 0.14 0.18 –– Max 125 0.35 0.40 0.68 0.39 0.34 0.67 0.18 0.24 –– Unit cd/m 2 –– –– –– –– –– –– –– –– –– Remarks White (All pixels on) Symbols Min Typical I CC1 –– 3.5mA I DD1 –– 0.16mA 0.2mA I CC2 –– –– 10 A I DD2 –– –– 10 A *All pixels shall be turned on with the maximum level gray scale **All pixels shall be turned o (while chip is operating) sales@greatecs.com www.greatecs.com 4 LCD Switches Programmable OLED Video Switch and Display SMARTSWITCH BLOCK DIAGRAM & PIN CONFIGURATIONS Color OLED Panel 52RGB x 36 SR1,SG1,SB1......SR52, SG52,SB52 COM1....COM36 IS Series Segment Driver Common Driver OLED Driver with Controller VDD VCC 1 7 SEG/COM Driving Block RES SCK SS SDI D/C 3 5 2 6 4 Gray Scale Decoder Oscillator Graphic Display Data RAM 96 x 64 x 16 Bit Display Timing Generator MCU Interface Command Decoder ISC01P GND 8 Pin No. 1 2 3 4 Symbol V DD SS RES D/C Name Power Slave Select Reset Data/Command Function Power source for logic circuit Slave select for SPI. This line is active low. Reset signal input. When pin is low, initialization of chip is executed Data/Command Control. When pin is pulled low, data will be interpreted as Command; when pulled high, data will be interpreted as Data. Clock line for SPI that synchronizes command and data Data input line for SPI Power source for drive OLED Connect to ground 5 6 7 8 SCK SDI VCC GND Serial Clock Serial Data In Power Ground SMARTSWITCH TYPICAL DIMENSIONS Terminal numbers are not on the switch. See Pixel Detail (12.9) .508 See Stando Detail (0.4) Typ .016 (10.0) .394 (0.65) Typ .026 (9.9) .390 (17.2) .677 (7.89) .311 (0.75) .030 (16.8) .661 (14.7) .579 (5.25) .207 (2.0) .079 (10.89) .429 (17.8) .701 (0.7) .028 (9.9) .390 (0.2) (2.0) .008 .079 (3.0) .118 (1.0) Typ .039 (7.0) .276 (15.0) .591 (15.0) .591 (10.0) .394 (0.4) Typ .016 Pixel Detail (0.21)Typ .0083 (0.02) Typ .0008 Pixel Detail A (0.22) .0087 (0.19) .0075 (0.04) Typ .0016 (0.07) Typ .0028 R Footprint (0.22) Typ .0087 RGBR (16.8) .661 8 7 2 1 (14.7) .579 (5.25) .207 (2.0) .079 3x (0.9) Dia .035 Landless 8x (.075) Dia .029 (0.02) Typ .0008 4x (0.9) Dia .035 (0.21) .0083 (1.0)Typ .039 (7.0) .276 See Pixel Detail A sales@greatecs.com www.greatecs.com 5 LCD Switches Programmable OLED Video Switch and Display TIMING SPECIFICATIONS FOR SMARTSWITCH & SMARTDISPLAY AC Characteristics (Temperature at 25°C) , V DD = 2.4V ~ 3.5V) Items Clock Cycle Time D/C Setup Time D/C Hold Time SS Setup Time SS Hold Time Write Data Setup Time Write Data Hold Time SCK Low Time SCK High Time SCK Rise Time SCK Fall Time Symbols tc yc le tAS tAH tC SS tC SH tDSW tDHW tC LKL tC LKH tR tF Minimum 150ns 40ns 40ns 75ns 60ns 40ns 40ns 75ns 75ns –– –– Typical –– –– –– –– –– –– –– –– –– –– –– Maximum –– –– –– –– tR IS Series D/C tAS tAH tCSH SS tCSS tC LKH tcy cle –– –– –– –– –– 15ns 15ns SCK tF tD SW tC LKL tD H W D7 D6 D5 D4 D3 D2 D1 D0 SDI STATE TRANSITION 7 : Initialization State 0 Power OFF (VCC, VDD O F F) 1 : Power ON, 7 : Initialization 2 : Power OFF State 1 Display OFF (Sleep Mode) 3 : Display ON 4 : Display OFF 8 : Changing the Display State 2 Display ON 8 : Changing the Display State Number 0 1 2 State Power OFF Display OFF Display ON Display Sleep OFF OFF ON –– ON OFF V CC OFF ON ON VDD OFF ON ON Changing the Display Disable Enable Enable VDD 0V Power ON/OFF Sequence Initialization Setting State 0 Power ON Minimum 0µs State 1 State 2 Power OFF State 0 Minimum 0µs State Transition 1 2 3 4 7 8 Transition Power ON Power OFF Display ON Display OFF Initialization Image Rewriting Display Settings Index RES “L” or “Hi-z” Reset low pulse width Trw (minimum 3µs) “L” or “Hi-z” Minimum 3µs Refer to "Power ON/OFF Sequence" VCC Minimum 0µs Initialize Setting of Command/Data Send Display Data Dimmer, Scroll, etc. D/C SS “L” or “Hi-z” SCK SDI VDD level (due to ESD protection circuit between VDD and VCC ) “H” or “L” “L” or “Hi-z” sales@greatecs.com www.greatecs.com 6 LCD Switches Programmable OLED Video Switch and Display PRECAUTIONS FOR HANDLING & STORAGE ELECTROST AT IC SENSITIVE DEVICES IS Series ATTENTION Handling 1. The IS Series OLED devices are electrostatic sensitive. To avoid damage to IC, do not touch keytops unless properly isolated from static electricity. 2. Signal input under conditions not recommended may cause damage to the OLED unit or deterioration of the display. Follow directions regarding supply sequences of power and signal voltages. 3. If the OLED panel is broken, avoid contact with the contents and wash o any spills to the skin or clothing. 4. Limit operating force to switch keytop to 100.0N maximum, as excessive pressure may damage the OLED. 5. For OLED display, it is necessary for terminal of metal cover to be connected to a ground. 6. Recommended soldering time and temperature limits for OLED switch or display: 11 seconds maximum @ 270°C maximum; avoid temperatures exceeding 80°C at the OLED. 7. The IS series OLED devices are not process sealed. 8. If OLED unit is operated with the same display pattern, the di erence between the operation duration of adjacent pixels may be interpreted as di erence between luminosity of pixels. To minimize this di erence, operate OLED unit so that each pixel may be turned on at frequency as equal as possible. 9. For switch, clean cap surface with dry cloth. If further cleaning is needed, wipe with dampened cloth using neutral cleanser and dry with clean cloth. Do not use organic solvent. For display, avoid contact with any ux or detergent. If any liquids spill on display surface, immediately wipe with soft absorbent cloth. Storage 1. Store in original container and away from direct sunlight. 2. Keep away from static electricity. 3. Avoid extreme temperatures, high humidity, gaseous substances, and all forms of chemical contamination. sales@greatecs.com www.greatecs.com 7