GS74104AGP-10

GS74104ATP/J SOJ, TSOP Commercial Temp Industrial Temp Features • Fast access time: 8, 10, 12 ns • CMOS low power operation: 120/95/85 mA at minimum cycle time • Single 3.3 V power supply • All inputs and outputs are TTL-compatible • Fully static operation • Industrial Temperature Option: –40° to 85°C • Package line up J: 400 mil, 32-pin SOJ package GJ:RoHS-compliant 400 mil, 32-pin SOJ package TP: 400 mil, 44-pin TSOP Type II package GP:RoHS-compliant 400 mil, 44-pin TSOP Type II package A4 A3 A2 A1 A0 CE DQ1 VDD VSS DQ2 WE A19 A18 A17 A16 A15 1M x 4 4Mb Asynchronous SRAM 8, 10, 12 ns 3.3 V VDD Center VDD and VSS SOJ 1M x 4-Pin Configuraton 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 A5 A6 A7 A8 A9 OE DQ4 VSS VDD DQ3 A10 A11 A12 A13 A14 NC 32-pin 400 mil SOJ Description The GS74104A is a high speed CMOS Static RAM organized as 1,048,576 words by 4 bits. Static design eliminates the need for external clocks or timing strobes. The GS operates on a single 3.3 V power supply and all inputs and outputs are TTLcompatible. The GS74104A is available in 400 mil SOJ and 400 mil TSOP Type-II packages. TSOP-II 1M x 4-Pin Configuration NC NC NC A4 A3 A2 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 44 43 42 41 40 39 38 37 36 35 NC NC NC A5 A6 A7 A8 A9 OE DQ4 VSS VDD DQ3 A10 A11 A12 A13 A14 NC NC NC NC Pin Descriptions Symbol A0–A19 DQ1–DQ4 CE WE OE VDD VSS NC Description Address input Data input/output Chip enable input Write enable input Output enable input +3.3 V power supply Ground No connect A1 A0 CE DQ1 VDD VSS DQ2 WE A19 A18 A17 A16 A15 NC NC NC 44-pin 400 mil TSOP II 34 33 32 31 30 29 28 27 26 25 24 23 Rev: 1.06 6/2006 1/11 © 2001, GSI Technology Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. GS74104ATP/J Block Diagram A0 Address Input Buffer Row Decoder Memory Array A19 CE WE OE Column Decoder Control I/O Buffer DQ1 DQ4 Truth Table CE H L L L Note: X: “H” or “L” OE X L X H WE X H L H DQ1 to DQ8 Not Selected Read Write High Z VDD Current ISB1, ISB2 IDD Rev: 1.06 6/2006 2/11 © 2001, GSI Technology Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. GS74104ATP/J Absolute Maximum Ratings Parameter Supply Voltage Input Voltage Output Voltage Allowable power dissipation Storage temperature Symbol VDD VIN VOUT PD TSTG Rating –0.5 to +4.6 –0.5 to VDD +0.5 (≤ 4.6 V max.) –0.5 to VDD +0.5 (≤ 4.6 V max.) 0.7 –55 to 150 Unit V V V W o C Note: Permanent device damage may occur if Absolute Maximum Ratings are exceeded. Functional operation shall be restricted to Recommended Operating Conditions. Exposure to higher than recommended voltages for extended periods of time could affect device reliability. Recommended Operating Conditions Parameter Supply Voltage for -8/-10/-12 Input High Voltage Input Low Voltage Ambient Temperature, Commercial Range Ambient Temperature, Industrial Range Symbol VDD VIH VIL TAc TAI Min 3.0 2.0 –0.3 0 –40 Typ 3.3 — — — — Max 3.6 VDD +0.3 0.8 70 85 Unit V V V oC o C Notes: 1. Input overshoot voltage should be less than VDD +2 V and not exceed 20 ns. 2. Input undershoot voltage should be greater than –2 V and not exceed 20 ns. Capacitance Parameter Input Capacitance Output Capacitance Symbol CIN COUT Test Condition VIN = 0 V VOUT = 0 V Max 5 7 Unit pF pF Notes: 1. Tested at TA = 25°C, f = 1 MHz 2. These parameters are sampled and are not 100% tested. Rev: 1.06 6/2006 3/11 © 2001, GSI Technology Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. GS74104ATP/J DC I/O Pin Characteristics Parameter Input Leakage Current Output Leakage Current Output High Voltage Output Low Voltage Symbol IIL ILO VOH VOL Test Conditions VIN = 0 to VDD Output High Z VOUT = 0 to VDD IOH = –4mA ILO = +4mA Min – 1 uA –1 uA 2.4 — Max 1 uA 1 uA — 0.4 V Power Supply Currents Parameter Symbol Test Conditions CE ≤ VIL All other inputs ≥ VIH or ≤ VIL Min. cycle time IOUT = 0 mA CE ≥ VIH All other inputs ≥ VIH or ≤VIL Min. cycle time CE ≥ VDD - 0.2V All other inputs ≥ VDD - 0.2V or ≤ 0.2V 0 to 70°C 8 ns 10 ns 12 ns 8 ns –40 to 85°C 10 ns 12 ns Operating Supply Current ID D 120 mA 95 mA 85 mA 130 mA 105 mA 95 mA Standby Current ISB1 30 mA 25 mA 22 mA 40 mA 35 mA 32 mA Standby Current ISB2 10 mA 20 mA Rev: 1.06 6/2006 4/11 © 2001, GSI Technology Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. GS74104ATP/J AC Test Conditions Parameter Input high level Input low level Input rise time Input fall time Input reference level Output reference level Output load Conditions VIH = 2.4 V VIL = 0.4 V tr = 1 V/ns tf = 1 V/ns 1.4 V 1.4 V Fig. 1& 2 Output Load 1 DQ 50Ω VT = 1.4 V 30pF1 Output Load 2 3.3 V DQ 5pF1 589Ω 434Ω Notes: 1. Include scope and jig capacitance. 2. Test conditions as specified with output loading as shown in Fig. 1 unless otherwise noted. 3. Output load 2 for tLZ, tHZ, tOLZ and tOHZ AC Characteristics Read Cycle Parameter Read cycle time Address access time Chip enable access time (CE) Output enable to output valid (OE) Output hold from address change Chip enable to output in low Z (CE) Output enable to output in low Z (OE) Chip disable to output in High Z (CE) Output disable to output in High Z (OE) * These parameters are sampled and are not 100% tested. Symbol tRC tAA tAC tOE tOH tLZ* tOLZ* tHZ* tOHZ* -8 Min 8 — — — 3 3 0 — — Max — 8 8 3.5 — — — 4 3.5 Min 10 — — — 3 3 0 — — -10 Max — 10 10 4 — — — 5 4 Min 12 — — — 3 3 0 — — -12 Max — 12 12 5 — — — 6 5 Unit ns ns ns ns ns ns ns ns ns Rev: 1.06 6/2006 5/11 © 2001, GSI Technology Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. GS74104ATP/J Read Cycle 1: CE = OE = VIL, WE = VIH tRC Address tAA tOH Data Out Previous Data Data valid Read Cycle 2: WE = VIH tRC Address tAA CE tAC tLZ OE tOE Data Out tOLZ High impedance DATA VALID tHZ tOHZ Rev: 1.06 6/2006 6/11 © 2001, GSI Technology Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. GS74104ATP/J Write Cycle Parameter Write cycle time Address valid to end of write Chip enable to end of write Data set up time Data hold time Write pulse width Address set up time Write recovery time (WE) Write recovery time (CE) Output Low Z from end of write Write to output in High Z Symbol tWC tAW tCW tDW tDH tWP tAS tWR tWR1 tWLZ* tWHZ* -8 Min 8 5.5 5.5 4 0 5.5 0 0 0 3 — Max — — — — — — — — — — 3.5 Min 10 7 7 5 0 7 0 0 0 3 — -10 Max — — — — — — — — — — 4 Min 12 8 8 6 0 8 0 0 0 3 — -12 Max — — — — — — — — — — 5 Unit ns ns ns ns ns ns ns ns ns ns ns * These parameters are sampled and are not 100% tested. Write Cycle 1: WE control tWC Address tAW OE tCW CE tAS WE tDW Data In tWHZ Data Out HIGH IMPEDANCE DATA VALID tWR tWP tDH tWLZ Rev: 1.06 6/2006 7/11 © 2001, GSI Technology Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. GS74104ATP/J Write Cycle 2: CE control tWC Address tAW OE tAS CE tWP WE tDW Data In Data Out DATA VALID tWR1 tCW tDH HIGH IMPEDANCE 32-Pin SOJ, 400 mil Dimension in inch Symbol D L c E HE GE A A1 A2 B B1 e A Dimension in mm min — 0.66 2.67 0.33 0.61 0.15 20.83 10.04 — 10.93 9.00 2.08 — 0o nom — — 2.80 0.43 0.71 0.20 20.93 10.16 1.27 11.05 9.30 — — — max 3.70 — 2.92 0.53 0.81 0.30 21.06 10.28 — 11.17 9.60 — 0.10 10o min — 0.026 0.105 0.013 0.024 0.006 0.820 0.395 — 0.430 0.354 0.082 — 0o nom — — 0.110 0.017 0.028 0.008 0.824 0.400 0.05 0.435 0.366 — — — max 0.146 — 0.115 0.021 0.032 0.012 0.829 0.405 — 0.440 0.378 — 0.004 10o 1 c D E A A2 A1 y B B1 e HE Detail A Q GE L y Q Notes: 1. Dimension D& E do not include interlead flash. 2. Dimension B1 does not include dambar protrusion/intrusion. 3. Controlling dimension: inches Rev: 1.06 6/2006 8/11 © 2001, GSI Technology Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. GS74104ATP/J 44-Pin, 400 mil TSOP-II Dimension in inch 44 D 23 c Symbol A A1 A2 HE A Dimension in mm min — 0.05 0.95 0.25 — 18.31 10.06 — 11.56 0.40 — — 0o nom — — 1.00 0.35 0.15 18.41 10.16 0.80 11.76 0.50 0.80 — — max 1.20 — 1.05 0.45 — 18.51 10.26 — 11.96 0.60 — 0.10 5o min — 0.002 0.037 0.01 — 0.721 0.396 — 0.455 0.016 — — 0o nom — — 0.039 0.014 0.006 0.725 0.400 0.031 0.463 0.020 0.031 — — max 0.047 — 0.041 0.018 — 0.729 0.404 — 0.471 0.024 — 0.004 5o E B c D E e HE L 1 A2 e 22 B A A1 y L1 L L1 y Q Q Detail A Notes: 1. Dimension D& E do not include interlead flash. 2. Dimension B does not include dambar protrusion/intrusion. 3. Controlling dimension: mm Rev: 1.06 6/2006 9/11 © 2001, GSI Technology Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. GS74104ATP/J Ordering Information Part Number* GS74104ATP-8 GS74104ATP-10 GS74104ATP-12 GS74104ATP-8I GS74104ATP-10I GS74104ATP-12I GS74104AGP-8 GS74104AGP-10 GS74104AGP-12 GS74104AGP-8I GS74104AGP-10I GS74104AGP-12I GS74104AJ-8 GS74104AJ-10 GS74104AJ-12 GS74104AJ-8I GS74104AJ-10I GS74104AJ-12I GS74104AGJ-8 GS74104AGJ-10 GS74104AGJ-12 GS74104AGJ-8I GS74104AGJ-10I GS74104AGJ-12I Package 400 mil TSOP-II 400 mil TSOP-II 400 mil TSOP-II 400 mil TSOP-II 400 mil TSOP-II 400 mil TSOP-II RoHS-compliant 400 mil TSOP-II RoHS-compliant 400 mil TSOP-II RoHS-compliant 400 mil TSOP-II RoHS-compliant 400 mil TSOP-II RoHS-compliant 400 mil TSOP-II RoHS-compliant 400 mil TSOP-II 400 mil SOJ 400 mil SOJ 400 mil SOJ 400 mil SOJ 400 mil SOJ 400 mil SOJ RoHS-compliant 400 mil SOJ RoHS-compliant 400 mil SOJ RoHS-compliant 400 mil SOJ RoHS-compliant 400 mil SOJ RoHS-compliant 400 mil SOJ RoHS-compliant 400 mil SOJ Access Time 8 ns 10 ns 12 ns 8 ns 10 ns 12 ns 8 ns 10 ns 12 ns 8 ns 10 ns 12 ns 8 ns 10 ns 12 ns 8 ns 10 ns 12 ns 8 ns 10 ns 12 ns 8 ns 10 ns 12 ns Temp. Range Commercial Commercial Commercial Industrial Industrial Industrial Commercial Commercial Commercial Industrial Industrial Industrial Commercial Commercial Commercial Industrial Industrial Industrial Commercial Commercial Commercial Industrial Industrial Industrial Status MP MP MP MP MP MP PQ PQ PQ PQ PQ PQ MP MP MP MP MP MP PQ PQ PQ PQ PQ PQ Notes: 1. Customers requiring delivery in Tape and Reel should add the character “T” to the end of the part number. For example: GS74104TP-8T. 2. MP = Mass Production. PQ = Pre-Qualification. Rev: 1.06 6/2006 10/11 © 2001, GSI Technology Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. GS74104ATP/J 4Mb Asynchronous Datasheet Revision History Rev. Code: Old; New 74104A_r1 74104A_r1; 74104A_r1_01 74104A_r1_01; 74104A_r1_02 74104A_r1_02; 74104A_r1_03 74104A_r1_03; 74104A_r1_04 74104A_r1_04; 74104A_r1_05 74104A_r1_05; 74104A_r1_06 Types of Changes Format or Content Content/Format Content Content Content Content Content/Format Content6 Page #/Revisions/Reason • Created new datasheet • Added 6 ns speed bin • Updated all power numbers • Updated Recommended Operating Currents on page 3 • Added 7 ns bin to entire document • Add X package • Removed 6 ns speed bin from entire document • Removed all references to “X” package • Removed 7 ns speed bin from entire document • Updated format • Added RoHS-compliant information for TSOP-II package • Added RoHS-compliant 400 mil, 32-pin SOJ Rev: 1.06 6/2006 11/11 © 2001, GSI Technology Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.