Preliminary GS880F18/36T-10/11/11.5/12/14 100 Pin TQFP Commercial Temp Industrial Temp
Features
• Flow through mode operation. • 3.3V +10%/-5% Core power supply. • 2.5V or 3.3V I/O supply. • LBO pin for linear or interleaved burst mode. • Internal input resistors on mode pins allow floating mode pins. Default to Interleaved Pipelined Mode. • Byte write (BW) and/or global write (GW) operation. • Common data inputs and data outputs. • Clock Control, registered, address, data, and control. • Internal Self-Timed Write cycle. • Automatic power-down for portable applications. • 100-lead TQFP package -10 -11 -11.5 -12 -14 10ns 11ns 11.5ns 12ns 14ns Flow Through tKQ 2-1-1-1 tCycle 10ns 15ns 15ns 15ns 15ns IDD 225mA 180mA 180mA 180mA 175mA
512K x 18, 256K x 36 8Mb Sync Burst SRAMs
10ns - 14ns 3.3V VDD 3.3V & 2.5V I/O
broadest access to multiple vendor sources. Boards designed with FT pin pads tied low may be stuffed with GSI’s Pipeline/Flow through configurable Burst RAMS or any vendor’s Flow through or configurable Burst SRAM. Bumps designed with the FT pin location tied High or floating must employ a non-configurable Flow through Burst RAM, like this RAM, to achieve Flow through functionality. 88018/32/36TByte Write and Global Write Byte write operation is performed by using byte write enable (BW) input combined with one or more individual byte write signals (Bx). In addition, Global Write (GW) is available for writing all bytes at one time, regardless of the Byte Write control inputs.
Sleep Mode
Low power (Sleep mode) is attained through the assertion (High) of the ZZ signal, or by stopping the clock (CK). Memory data is retained during Sleep mode.
Core and Interface Voltages
The GS880F18/32/36T operates on a 3.3V power supply and all inputs/outputs are 3.3V and 2.5V compatible. Separate output power (VDDQ) pins are used to de-couple output noise from the internal circuit.
Functional Description
Applications
The GS880F18/32/36T is a 9,437,184 bit (8,388,608 bit for x32 version) high performance synchronous SRAM with a 2 bit burst address counter. Although of a type originally developed for Level 2 Cache applications supporting high performance CPU’s, the device now finds application in synchronous SRAM applications ranging from DSP main store to networking chip set support.
Controls
Addresses, data I/O’s, chip enables (E1, E2, E3), address burst control inputs (ADSP, ADSC, ADV ) and write control inputs (Bx, BW, GW) are synchronous and are controlled by a positive edge triggered clock input (CK). Output enable (G) and power down control (ZZ) are asynchronous inputs. Burst cycles can be initiated with either ADSP or ADSC inputs. In Burst mode, subsequent burst addresses are generated internally and are controlled by ADV. The burst address counter may be configured to count in either linear or interleave order with the Linear Burst Order (LBO) input. The Burst function need not be used. New addresses can be loaded on every cycle with no degradation of chip performance.
Designing For Compatibility
The JEDEC Standard for Burst RAMS calls for a FT mode pin option (pin 14 on TQFP). Board sites for Flow through Burst RAMS should be designed with V SS connected to the FT pin location to ensure the Rev: 1.03 3/2000 1/25 © 2000, Giga Semiconductor, Inc.
N
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
Preliminary GS880F18/36T-10/11/11.5/12/14
GS880F18 100 Pin TQFP Pinout
NC NC NC VDDQ VSS NC NC DQB1 DQB2 VSS VDDQ DQB3 DQB4 NC VDD NC VSS DQB5 DQB6 VDDQ VSS DQB7 DQB8 DQB9 NC VSS VDDQ NC NC NC
100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 1 80 2 79 3 78 4 77 5 76 6 75 7 74 8 73 9 72 512K x 18 10 71 Top View 11 70 12 69 13 68 14 67 15 66 16 65 17 64 18 63 19 62 20 61 21 60 22 59 23 58 24 57 25 56 26 55 27 54 28 53 29 52 30 51 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50
CK GW BW G AD SC AD SP A DV A8 A9
A6 A7 E1 E2 NC NC BB BA E3 VDD V SS
A18 NC NC VDDQ VSS NC DQA9 DQA8 DQA7 VSS VDDQ DQA6 DQA5 VSS NC VDD ZZ DQA4 DQA3 VDDQ VSS DQA2 DQA1 NC NC VSS VDDQ NC NC NC
LBO A5 A4
A3 A2 A1 A0 NC NC V SS VDD NC A17 A10 A11 A12 A13 A14 A15 2/25
Rev: 1.03 3/2000
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
A16 © 2000, Giga Semiconductor, Inc.
N
Preliminary GS880F18/36T-10/11/11.5/12/14
GS880F32 100 Pin TQFP Pinout
NC DQ C8 DQ C7 VDDQ VSS DQ C6 DQ C5 DQ C4 DQ C3 VSS VDDQ DQ C2 DQ C1 NC VDD NC VSS DQ D1 DQ D2 VDDQ VSS DQ D3 DQ D4 DQ D5 DQ D6 VSS VDDQ DQ D7 DQ D8 NC
100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 1 80 2 79 3 78 4 77 5 76 6 75 7 74 8 73 9 72 256K x 32 10 71 Top View 11 70 12 69 13 68 14 67 15 66 16 65 17 64 18 63 19 62 20 61 21 60 22 59 23 58 24 57 25 56 26 55 27 54 28 53 29 52 30 51 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50
CK GW BW G AD SC AD SP A DV A8 A9
A6 A7 E1 E2 BD BC BB BA E3 VDD V SS
NC DQB8 DQB7 VDDQ VSS DQB6 DQB5 DQB4 DQB3 VSS VDDQ DQB2 DQB1 VSS NC VDD ZZ DQA1 DQA2 VDDQ VSS DQA3 DQA4 DQA5 DQA6 VSS VDDQ DQA7 DQA8 NC
LBO A5 A4
A3 A2 A1 A0 NC NC V SS VDD NC A17 A10 A11 A12 A13 A14 A15 3/25
Rev: 1.03 3/2000
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
A16 © 2000, Giga Semiconductor, Inc.
N
Preliminary GS880F18/36T-10/11/11.5/12/14
GS880F36 100 Pin TQFP Pinout
DQ C9 DQ C8 DQ C7 VDDQ VSS DQ C6 DQ C5 DQ C4 DQ C3 VSS VDDQ DQ C2 DQ C1 NC VDD NC VSS DQ D1 DQ D2 VDDQ VSS DQ D3 DQ D4 DQ D5 DQ D6 VSS VDDQ DQ D7 DQ D8 DQ D9
100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 1 80 2 79 3 78 4 77 5 76 6 75 7 74 8 73 9 72 256K x 36 10 71 Top View 11 70 12 69 13 68 14 67 15 66 16 65 17 64 18 63 19 62 20 61 21 60 22 59 23 58 24 57 25 56 26 55 27 54 28 53 29 52 30 51 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50
CK GW BW G AD SC AD SP A DV A8 A9
A6 A7 E1 E2 BD BC BB BA E3 VDD V SS
DQB9 DQB8 DQB7 VDDQ VSS DQB6 DQB5 DQB4 DQB3 VSS VDDQ DQB2 DQB1 VSS NC VDD ZZ DQA1 DQA2 VDDQ VSS DQA3 DQA4 DQA5 DQA6 VSS VDDQ DQA7 DQA8 DQA9
LBO A5 A4
A3 A2 A1 A0 NC NC V SS VDD NC A17 A10 A11 A12 A13 A14 A15 4/25
Rev: 1.03 3/2000
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
A16 © 2000, Giga Semiconductor, Inc.
N
Preliminary GS880F18/36T-10/11/11.5/12/14
TQFP Pin Description Pin Location
37, 36 35, 34, 33, 32, 100, 99, 82, 81, 44, 45, 46, 47, 48, 49, 50, 43 80 63, 62, 59, 58, 57, 56, 53, 52 68, 69, 72, 73, 74, 75, 78, 79 13, 12, 9, 8, 7, 6, 3, 2 18, 19, 22, 23, 24, 25, 28, 29 51, 80, 1, 30 51, 80, 1, 30 58, 59, 62, 63, 68, 69, 72, 73, 74 8, 9, 12, 13, 18, 19, 22, 23, 24 51, 52, 53, 56, 57 75, 78, 79, 1, 2, 3, 6, 7 25, 28, 29, 30 16 66 87 93, 94 95, 96 95, 96 89 88 98, 92 97 86 83 84, 85 64 31 15, 41, 65, 91 5,10,17, 21, 26, 40, 55, 60, 67, 71, 76, 90 4, 11, 20, 27, 54, 61, 70, 77 14, 16, 38, 39, 42, 66
Symbol
A0, A1 A2-17 A18 DQ A1-DQA8 DQ B1-DQB8 DQC1-DQC8 DQD1-DQD8 DQA9, DQB9, DQC9, DQD9 NC DQ A1-DQA9 DQB1- DQB9 NC DP QE BW B A, B B BC, BD NC CK GW E1, E3 E2 G ADV ADSP, ADSC ZZ LBO VDD VSS VDDQ NC
Type
I I I I/O
Description
Address field LSB’s and Address Counter preset Inputs Address Inputs Address Inputs Data Input and Output pins. (x32, x36 Version)
I/O I/O
Data Input and Output pins. No Connect (x32 Version) Data Input and Output pins.
I O I I I I I I I I I I I I I I I -
No Connect Parity Input. 1 = Even, 0 = Odd. Parity Error Out. Open Drain Output. Byte Write. Writes all enabled bytes. Active Low. Byte Write Enable for DQA, DQB Data I/O’s. Active Low. Byte Write Enable for DQC, DQD Data I/O’s. Active Low. (x32, x36 Version) No Connect (x18 Version) Clock Input Signal. Active High. Global Write Enable. Writes all bytes. Active Low. Chip Enable. Active Low. Chip Enable. Active High. Output Enable. Active Low. Burst address counter advance enable. Active Low. Address Strobe (Processor, Cache Controller). Active Low. Sleep Mode control. Active High. Linear Burst Order mode. Active Low. Core power supply. I/O and Core Ground. Output driver power supply. No Connect.
Rev: 1.03 3/2000
5/25
© 2000, Giga Semiconductor, Inc.
N
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
Preliminary GS880F18/36T-10/11/11.5/12/14
GS880F18/32/36 Block Diagram
Register
A0-An
D
Q A0 D0 A1 D1 Q1 Counter Load A Q0 A0 A1
LBO ADV CK ADSC ADSP GW BW BA
Register
Memory Array
Q D Q D
Register
36
4
36
D BB
Q
Register
D BC
Q Q
Regist er
D
Re gister
Q
Register
D
D BD
Q
Register
D
Q
E1 E2 E3
Register
D
Q
Register
D
Q
0 G Power Down Control
ZZ
1
DQx0-DQx9
Note: Only x36 version shown for simplicity.
Rev: 1.03 3/2000
6/25
© 2000, Giga Semiconductor, Inc.
N
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
Preliminary GS880F18/36T-10/11/11.5/12/14
Mode Pin Functions Mode Name
Burst Order Control Power Down Control
Pin Name State
LBO ZZ L H or NC L or NC H
Function
Linear Burst Interleaved Burst Active Standby, IDD = ISB
Note: There is a pull up device on the LBO pin and a pull down device on the ZZ pin, so those input pins can be unconnected and the chip will operate in the default states as specified in the above tables.
Burst Counter Sequences
Linear Burst Sequence
A[1:0] 1st address 2nd address 3rd address 4th address 00 01 10 11 A[1:0] 01 10 11 00 A[1:0] 10 11 00 01 A[1:0] 11 00 01 10 1st address 2nd address 3rd address 4th address
Interleaved Burst Sequence
A[1:0] 00 01 10 11 A[1:0] 01 00 11 10 A[1:0] 10 11 00 01 A[1:0] 11 10 01 00
BPR 1999.05.18
Note: The burst counter wraps to initial state on the 5th clock.
Note: The burst counter wraps to initial state on the 5th clock.
Byte Write Truth Table Function
Read Read Write byte a Write byte b Write byte c Write byte d Write all bytes Write all bytes
GW
H H H H H H H L
BW
H L L L L L L X
BA
X H L H H H L X
BB
X H H L H H L X
BC
X H H H L H L X
BD
X H H H H L L X
Notes
1 1 2, 3 2, 3 2, 3, 4 2, 3, 4 2, 3, 4
Note: 1. All byte outputs are active in read cycles regardless of the state of Byte Write Enable inputs. 2. Byte Write Enable inputs BA, BB, BC and/or BD may be used in any combination with BW to write single or multiple bytes. 3. All byte I/O’s remain High-Z during all write operations regardless of the state of Byte Write Enable inputs. 4. Bytes “C” and “D” are only available on the x32 and x36 versions.
Rev: 1.03 3/2000
7/25
© 2000, Giga Semiconductor, Inc.
N
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
Preliminary GS880F18/36T-10/11/11.5/12/14
Synchronous Truth Table Operation
Deselect Cycle, Power Down Deselect Cycle, Power Down Deselect Cycle, Power Down Read Cycle, Begin Burst Read Cycle, Begin Burst Write Cycle, Begin Burst Read Cycle, Continue Burst Read Cycle, Continue Burst Write Cycle, Continue Burst Write Cycle, Continue Burst Read Cycle, Suspend Burst Read Cycle, Suspend Burst Write Cycle, Suspend Burst Write Cycle, Suspend Burst
Address Used
None None None External External External Next Next Next Next Current Current Current Current
State Diagram Key5
X X X R R W CR CR CW CW
E1
H L L L L L X H X H X H X H
E22
(x36only)
ADSP ADSC
X L H L H H H X H X H X H X L X L X L L H H H H H H H H
ADV
X X X X X X L L L L H H H H
W3
X X X X F T F F T T F F T T
DQ4
High-Z High-Z High-Z Q Q D Q Q D D Q Q D D
X F F T T T X X X X X X X X
Note: 1. X = Don’t Care, H = High, L = Low. 2. For x36 Version, E = T (True) if E2 = 1 and E3 = 0 ; E = F (False) if E2 = 0 or E3 = 1. 3. W = T (True) and F (False) is defined in the Byte Write Truth Table preceding. 4. G is an asynchronous input. G can be driven high at any time to disable active output drivers. G low can only enable active drivers (shown as “Q” in the Truth Table above). 5. 6. 7. All input combinations shown above are tested and supported. Input combinations shown in gray boxes need not be used to accomplish basic synchronous or synchronous burst operations and may be avoided for simplicity. Tying ADSP high and ADSC low allows simple non-burst synchronous operations. See BOLD items above. Tying ADSP high and ADV low while using ADSC to load new addresses allows simple burst operations. See ITALIC items above.
Rev: 1.03 3/2000
8/25
© 2000, Giga Semiconductor, Inc.
N
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
Preliminary GS880F18/36T-10/11/11.5/12/14 Simplified State Diagram
X
Deselect W W Simple Synchronous Operation R R
X CW
First Write
R CR
First Read
X CR
Simple Burst Synchronous Operation
W R X Burst Write CR CW
R
Burst Read
X
CR
Notes: 1. The diagram shows only supported (tested) synchronous state transitions. The diagram presumes G is tied Low. 2. The upper portion of the diagram assumes active use of only the Enable (E1E2) and Write (BA, BB, BC, BD, BW and GW) control inputs and that ADSP is tied high and ADSC is tied low. 3. The upper and lower portions of the diagram together assume active use of only the Enable, Write and ADSC control inputs and assumes ADSP is tied high and ADV is tied low.
Rev: 1.03 3/2000
9/25
© 2000, Giga Semiconductor, Inc.
N
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
Preliminary GS880F18/36T-10/11/11.5/12/14 Simplified State Diagram with G
X
Deselect W W X W CW R R
First Write
R CR
First Read
X CR
CW
W X Burst Write R CR W CW
R X
Burst Read
CW
CR
Notes: 1. The diagram shows supported (tested) synchronous state transitions plus supported transitions that depend upon the use of G. 2. Use of “Dummy Reads” (Read Cycles with G High) may be used to make the transition from Read cycles to Write cycles without passing through a Deselect cycle. Dummy Read cycles increment the address counter just like normal Read cycles. 3. Transitions shown in grey tone assume G has been pulsed high long enough to turn the RAM’s drivers off and for incoming data to meet Data Input Set Up Time.
Rev: 1.03 3/2000
10/25
© 2000, Giga Semiconductor, Inc.
N
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
Preliminary GS880F18/36T-10/11/11.5/12/14
Absolute Maximum Ratings
(All voltages reference to VSS)
Symbol
VDD VDDQ VCK VI/O VIN IIN IOUT PD TSTG TBIAS
Description
Voltage on VDD Pins Voltage in VDDQ Pins Voltage on Clock Input Pin Voltage on I/O Pins Voltage on Other Input Pins Input Current on Any Pin Output Current on Any I/O Pin Package Power Dissipation Storage Temperature Temperature Under Bias
Value
-0.5 to 4.6 -0.5 to VDD -0.5 to 6 -0.5 to VDDQ+0.5 (≤ 4.6 V max.) -0.5 to VDD+0.5 (≤ 4.6 V max.) +/- 20 +/- 20 1.5 -55 to 125 -55 to 125
Unit
V V V V V mA mA W
oC oC
Note: Permanent damage to the device may occur if the Absolute Maximum Ratings are exceeded. Operation should be restricted to Recommended Operating Conditions. Exposure to conditions exceeding the Absolute Maximum Ratings, for an extended period of time, may affect reliability of this component.
Recommended Operating Conditions Parameter
Supply Voltage I/O Supply Voltage Input High Voltage Input Low Voltage Ambient Temperature (Commercial Range Versions) Ambient Temperature (Industrial Range Versions)
Symbol
VDD VDDQ VIH VIL TA TA
Min.
3.135 2.375 1.7 -0.3 0 -40
Typ.
3.3 2.5 ----25 25
Max.
3.6 VDD VDD+0.3 0.8 70 85
Unit
V V V V °C °C
Notes
1 2 2 3 3
Note: 1. Unless otherwise noted, all performance specifications quoted are evaluated for worst case at both 2.75V ≤ VDDQ ≤ 2.375V (i.e. 2.5V I/O) and 3.6V ≤ VDDQ ≤ 3.135V (i.e. 3.3V I/O) and quoted at whichever condition is worst case. 2. This device features input buffers compatible with both 3.3V and 2.5V I/O drivers. 3. Most speed grades and configurations of this device are offered in both Commercial and Industrial Temperature ranges. The part number of Industrial Temperature Range versions end the character “I”. Unless otherwise noted, all performance specifications quoted are evaluated for worst case in the temperature range marked on the device. 4. Input Under/overshoot voltage must be -2V > Vi < V DD+2V with a pulse width not to exceed 20% tKC.
Rev: 1.03 3/2000
11/25
© 2000, Giga Semiconductor, Inc.
N
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
Preliminary GS880F18/36T-10/11/11.5/12/14
Undershoot Measurement and Timing
VIH VDD+-2.0V VSS 50% VSS-2.0V 20% tKC VIL 50% VDD
Overshoot Measurement and Timing
20% tKC
Note: This parameter is sample tested.
Package Thermal Characteristics Rating
Junction to Ambient (at 200 lfm) Junction to Ambient (at 200 lfm) Junction to Case (TOP)
Layer Board
single four
Symbol
RΘJA RΘJA RΘJC
Max
40 24 9
Unit
°C/W °C/W °C/W
Notes
1,2 1,2 3
Notes: 1. Junction temperature is a function of SRAM power dissipation, package thermal resistance, mounting board temperature, ambient. Temperature air flow, board density, and PCB thermal resistance. 2. SCMI G-38-87. 3. Average thermal resistance between die and top surface, MIL SPEC-883, Method 1012.1.
AC Test Conditions Parameter
Input high level Input low level Input slew rate Input reference level Output reference level Output load
Conditions
2.3V 0.2V 1V/ns 1.25V 1.25V Fig. 1& 2
Notes: 1. Include scope and jig capacitance. 2. Test conditions as specified with output loading as shown in Fig. 1 unless otherwise noted. 3. Output Load 2 for tLZ, tHZ, tOLZ and tOHZ. 4. Device is deselected as defined by the Truth Table.
Rev: 1.03 3/2000
12/25
© 2000, Giga Semiconductor, Inc.
N
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
Preliminary GS880F18/36T-10/11/11.5/12/14
Output Load 1 DQ 50Ω VT=1.25V
* Distributed Test Jig Capacitance
Output Load 2 2.5V 30pF* DQ 5pF* 225Ω 225Ω
DC Electrical Characteristics Parameter
Input Leakage Current (except mode pins) ZZ Input Current Mode Pin Input Current Output Leakage Current Output High Voltage Output High Voltage Output Low Voltage
Symb ol
IIL IINZZ IINM IOL VOH VOH VOL
Test Conditions
VIN = 0 to VDD VDD ≥ VIN ≥ VIH 0V ≤ VIN ≤ VIH VDD ≥ VIN ≥ VIL 0V ≤ VIN ≤ VIL Output Disable, VOUT = 0 to VDD IOH = - mA, VDDQ=2.375V IOH = - mA, VDDQ=3.135V IOL = mA
Min
-1uA -1uA -1uA -uA -1uA -1uA 1.7V 2.4V
Max
1uA 1uA uA 1uA 1uA 1uA
0.4V
Rev: 1.03 3/2000
13/25
© 2000, Giga Semiconductor, Inc.
N
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
Preliminary GS880F18/36T-10/11/11.5/12/14
Absolute Maximum Ratings
(All voltages reference to VSS)
Symbol
VDD VDDQ VCK VI/O VIN IIN IOUT PD TSTG TBIAS
Description
Voltage on VDD Pins Voltage in VDDQ Pins Voltage on Clock Input Pin Voltage on I/O Pins Voltage on Other Input Pins Input Current on Any Pin Output Current on Any I/O Pin Package Power Dissipation Storage Temperature Temperature Under Bias
Value
-0.5 to 4.6 -0.5 to VDD -0.5 to 6 -0.5 to VDDQ+0.5 (≤ 4.6 V max.) -0.5 to VDD+0.5 (≤ 4.6 V max.) +/- 20 +/- 20 1.5 -55 to 125 -55 to 125
Unit
V V V V V mA mA W
oC oC
Note: Permanent damage to the device may occur if the Absolute Maximum Ratings are exceeded. Operation should be restricted to Recommended Operating Conditions. Exposure to conditions exceeding the Absolute Maximum Ratings, for an extended period of time, may affect reliability of this component.
Recommended Operating Conditions Parameter
Supply Voltage I/O Supply Voltage Input High Voltage Input Low Voltage Ambient Temperature (Commercial Range Versions) Ambient Temperature (Industrial Range Versions)
Symbol
VDD VDDQ VIH VIL TA TA
Min.
3.135 2.375 1.7 -0.3 0 -40
Typ.
3.3 2.5 ----25 25
Max.
3.6 VDD VDD+0.3 0.8 70 85
Unit
V V V V °C °C
Notes
1 2 2 3 3
Note: 1. Unless otherwise noted, all performance specifications quoted are evaluated for worst case at both 2.75V ≤ VDDQ ≤ 2.375V (i.e. 2.5V I/O) and 3.6V ≤ VDDQ ≤ 3.135V (i.e. 3.3V I/O) and quoted at whichever condition is worst case. 2. This device features input buffers compatible with both 3.3V and 2.5V I/O drivers. 3. Most speed grades and configurations of this device are offered in both Commercial and Industrial Temperature ranges. The part number of Industrial Temperature Range versions end the character “I”. Unless otherwise noted, all performance specifications quoted are evaluated for worst case in the temperature range marked on the device. 4. Input Under/overshoot voltage must be -2V > Vi < V DD+2V with a pulse width not to exceed 20% tKC.
Rev: 1.03 3/2000
14/25
© 2000, Giga Semiconductor, Inc.
N
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
Preliminary GS880F18/36T-10/11/11.5/12/14
Undershoot Measurement and Timing
VIH VDD+-2.0V VSS 50% VSS-2.0V 20% tKC VIL 50% VDD
Overshoot Measurement and Timing
20% tKC
Note: This parameter is sample tested.
Package Thermal Characteristics Rating
Junction to Ambient (at 200 lfm) Junction to Ambient (at 200 lfm) Junction to Case (TOP)
Layer Board
single four
Symbol
RΘJA RΘJA RΘJC
Max
40 24 9
Unit
°C/W °C/W °C/W
Notes
1,2 1,2 3
Notes: 1. Junction temperature is a function of SRAM power dissipation, package thermal resistance, mounting board temperature, ambient. Temperature air flow, board density, and PCB thermal resistance. 2. SCMI G-38-87. 3. Average thermal resistance between die and top surface, MIL SPEC-883, Method 1012.1.
AC Test Conditions Parameter
Input high level Input low level Input slew rate Input reference level Output reference level Output load
Conditions
2.3V 0.2V 1V/ns 1.25V 1.25V Fig. 1& 2
Notes: 1. Include scope and jig capacitance. 2. Test conditions as specified with output loading as shown in Fig. 1 unless otherwise noted. 3. Output Load 2 for tLZ, tHZ, tOLZ and tOHZ. 4. Device is deselected as defined by the Truth Table.
Rev: 1.03 3/2000
15/25
© 2000, Giga Semiconductor, Inc.
N
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
Preliminary GS880F18/36T-10/11/11.5/12/14
Output Load 1 DQ 50Ω VT=1.25V
* Distributed Test Jig Capacitance
Output Load 2 2.5V 30pF* DQ 5pF* 225Ω 225Ω
DC Electrical Characteristics Parameter
Input Leakage Current (except mode pins) ZZ Input Current Mode Pin Input Current Output Leakage Current Output High Voltage Output High Voltage Output Low Voltage
Symb ol
IIL IINZZ IINM IOL VOH VOH VOL
Test Conditions
VIN = 0 to VDD VDD ≥ VIN ≥ VIH 0V ≤ VIN ≤ VIH VDD ≥ VIN ≥ VIL 0V ≤ VIN ≤ VIL Output Disable, VOUT = 0 to VDD IOH = - mA, VDDQ=2.375V IOH = - mA, VDDQ=3.135V IOL = mA
Min
-1uA -1uA -1uA -uA -1uA -1uA 1.7V 2.4V
Max
1uA 1uA uA 1uA 1uA 1uA
0.4V
Operating Currents
Parameter Test Conditions Symbol
Device Selected;
-10
0 to 70°C -40 to 85°C 0 to 70°C
-11
-40 to 85°C
-11.5
0 to 70°C -40 to 85°C 0 to 70°C
-12
-40 to 85°C 0 to 70°C
-14
-40 to 85°C
IDD Operating All other inputs 225mA 235mA 180mA 190mA 180mA 190mA 180mA 190mA 175mA 185mA ≥VIH or ≤ VIL Flow-Thru Current Output open
Standby Current Deselect Current
ZZ ≥ VDD - 0.2V
ISB Flow-Thru
30mA
40mA
30mA
40mA
30mA
40mA
30mA
40mA
30mA
40mA
Device Deselected; IDD All other inputs Flow-Thru ≥ VIH or ≤ VIL
80mA
90mA
65mA
75mA
65mA
75mA
65mA
75mA
55
65
Rev: 1.03 3/2000
16/25
© 2000, Giga Semiconductor, Inc.
N
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
Preliminary GS880F18/36T-10/11/11.5/12/14 AC Electrical Characteristics
Parameter
Clock Cycle Time FlowThru Clock to Output Valid Clock to Output Invalid Clock to Output in Low-Z Clock HIGH Time Clock LOW Time Clock to Output in High-Z G to Output Valid G to output in Low-Z G to output in High-Z Setup time Hold time ZZ setup time ZZ hold time ZZ recovery
Symbol
tKC tKQ tKQX tLZ
1
-10
Min 10.0 --3.0 3.0 1.3 1.5 1.5 --0 --1.5 0.5 5 1 20 Max --8.0 --------3.2 3.2 --3.2 ----------Min
-11
Max --10.0 --------3.8 3.8 --3.8 ----------10.0 --3.0 3.0 1.5 1.7 1.5 --0 --1.5 0.5 5 1 20
-11.5
Min 15.0 --3.0 3.0 1.7 2 1.5 --0 --1.5 0.5 5 1 20 Max --11.0 --------4.0 4.0 --4.0 ----------Min
-12
Max --11.5 --------4.2 4.2 --4.2 ----------Min 15.0 --3.0 3.0 1.7 2 1.5 --0 --2.0 0.5 5 1 20
-14
Max --12.0 --------4.5 4.5 --4.5 ----------15.0 --3.0 3.0 2 2.2 1.5 --0 --2.0 0.5 5 1 20
Unit
ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns
tKH tKL tHZ1 tOE tOLZ1 tOHZ1 tS tH tZZS2 tZZH2 tZZR
Notes: 1. These parameters are sampled and are not 100% tested 2. ZZ is an asynchronous signal. However, In order to be recognized on any given clock cycle, ZZ must meet the specified setup and hold times as specified above.
Rev: 1.03 3/2000
17/25
© 2000, Giga Semiconductor, Inc.
N
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
Preliminary GS880F18/36T-10/11/11.5/12/14 Write Cycle Timing
Single Write
Burst Write
Write
Deselected
CK
tS tH
tKH tKL
tKC
ADSP is blocked by E inactive
ADSP
tS tH ADSC initiated write
ADSC
tS tH
ADV
tS tH ADV must be inactive for ADSP Write
WR2 WR3
A0-An GW
WR1
tS tH
tS tH
BW
tS tH
BA - BD
tS tH
WR1 WR1
WR2
WR3 WR3
E1 masks ADSP
E1
tS tH Deselected with E2
E2
tS tH E2 and E3 only sampled with ADSP or ADSC
E3 G
tS tH Write specified byte for 2A and all bytes for 2B, 2c& 2D
D2A D2B D2C D2D D3A
DQA - DQD
Hi-Z
D1A
Rev: 1.03 3/2000
18/25
© 2000, Giga Semiconductor, Inc.
N
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
Preliminary GS880F18/36T-10/11/11.5/12/14 Flow Through Read-Write Cycle Timing
Single Read Single Write
Burst Read
CK
tS tH tKH tKL tKC ADSP is blocked by E inactive
ADSP
tS tH ADSC initiated read
ADSC
tS tH
ADV
tS tH
A0-An GW
RD1
WR1
RD2
tS tH
tS
tS tH
BW BA - BD
tS tH tS
WR1
tH
E1 masks ADSP
E1
tS tH E2 and E3 only sampled with ADSP and ADSC
E2
tS tH Deselected with E3
E3
tOE tOHZ
G
tKQ tS Q1A tH Q2A Q2B Q2c Q2D Q2A
DQA - DQD
Hi-Z
D1A
Burst wrap around to it’s initial state
Rev: 1.03 3/2000
19/25
© 2000, Giga Semiconductor, Inc.
N
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
Preliminary GS880F18/36T-10/11/11.5/12/14 Flow Through Read Cycle Timing
Single Read tKL
Burst Read
CK
tS tH tKH tKC ADSP is blocked by E inactive
ADSP
tS tH ADSC initiated read
ADSC
tS tH Suspend Burst Suspend Burst
ADV
tS tH
A0-An GW
RD1 tS
RD2
RD3 tH
tS
tH
BW BA - BD
tS tH E1 masks ADSP
E1
tS tH E2 and E3 only sampled with ADSP or ADSC Deselected with E 2
E2
tS tH
E3
tOE tOHZ
G
tOLZ tKQX Q1A tLZ tKQ tHZ Q2A Q2B Q2C Q2D Q3A tKQX
DQA-DQD
Hi-Z
Rev: 1.03 3/2000
20/25
© 2000, Giga Semiconductor, Inc.
N
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
Preliminary GS880F18/36T-10/11/11.5/12/14
Sleep Mode Timing Diagram
CK
tS tH tKC tKH tKL
ADSP ADSC
tZZS
~~~~~ ~ ~ ~~ ~
tZZH
tZZR
ZZ
Snooze
Rev: 1.03 3/2000
21/25
© 2000, Giga Semiconductor, Inc.
N
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
Preliminary GS880F18/36T-10/11/11.5/12/14 Output Driver Characteristics
120.0
100.0
Pull Down Drivers
80.0
60.0
40.0
20.0
VDDQ I Out
I Out (mA)
0.0
VOut
-20.0
VSS
-40.0
-60.0
-80.0
Pull Up Drivers
-100.0
-120.0
-140.0 -0.5 0 0.5 1 1.5 2 2.5 3 3.5 4
V Out (Pull Down) VDDQ - V Out (Pull Up) 3.6V PD HD 3.3V PD HD 3.1V PD HD 3.1V PU HD 3.3V PU HD 3.6V PU HD
Rev: 1.03 3/2000
22/25
© 2000, Giga Semiconductor, Inc.
N
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
Preliminary GS880F18/36T-10/11/11.5/12/14 TQFP Package Drawing
Symbol
A1 A2 b c D D1 E E1 e L L1 Y θ
Description
Standoff Body Thickness Lead Width Lead Thickness Terminal Dimension Package Body Terminal Dimension Package Body Lead Pitch Foot Length Lead Length Coplanarity Lead Angle
Min.
0.05 1.35 0.20 0.09 21.9 19.9 15.9 13.9 0.45
Nom.
0.10 1.40 0.30 22.0 20.0 16.0 14.0 0.65 0.60 1.00
Max
0.15 1.45 0.40 0.20 22.1 20.1 16.1 14.1
L L1
θ c P in 1
D1
e b
D
0.75 0.10
0°
7°
Notes: 1. All dimensions are in millimeters (mm). 2. Package width and length do not include mold protrusion
A1
Y
A2
E1 E
BPR 1999.05.18
Rev: 1.03 3/2000
23/25
© 2000, Giga Semiconductor, Inc.
N
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
Preliminary GS880F18/36T-10/11/11.5/12/14 Ordering Information for GSI Synchronous Burst RAMs
Org
512K x 18 512K x 18 512K x 18 512K x 18 512K x 18 256K x 32 256K x 32 256K x 32 256K x 32 256K x 32 256K x 36 256K x 36 256K x 36 256K x 36 256K x 36 512K x 18 512K x 18 512K x 18 512K x 18 512K x 18 256K x 32 256K x 32 256K x 32 256K x 32 256K x 32 256K x 36 256K x 36 256K x 36 256K x 36 256K x 36
Part Number1
GS880F18T-10 GS880F18T-11 GS880F18T-11.5 GS880F18T-12 GS880F18T-14 GS880F32T-10 GS880F32T-11 GS880F32T--11.5 GS880F32T-12 GS880F32T-14 GS880F36T-10 GS880F36T-11 GS880F36T--11.5 GS880F36T-12 GS880F36T-14 GS880F18T-10I GS880F18T-11I GS880F18T--11.5I GS880F18T-12I GS880F18T-14I GS880F32T-10 GS880F32T-11 GS880F32T--11.5 GS880F32T-12 GS880F32T-14 GS880F36T-10I GS880F36T-11I GS880F36T--11.5I GS880F36T-12I GS880F36T-14I
Type
Flow Through Flow Through Flow Through Flow Through Flow Through Flow Through Flow Through Flow Through Flow Through Flow Through Flow Through Flow Through Flow Through Flow Through Flow Through Flow Through Flow Through Flow Through Flow Through Flow Through Flow Through Flow Through Flow Through Flow Through Flow Through Flow Through Flow Through Flow Through Flow Through Flow Through
Package
TQFP TQFP TQFP TQFP TQFP TQFP TQFP TQFP TQFP TQFP TQFP TQFP TQFP TQFP TQFP TQFP TQFP TQFP TQFP TQFP TQFP TQFP TQFP TQFP TQFP TQFP TQFP TQFP TQFP TQFP
Speed2 (Mhz/ns)
10 11 11.5 12 14 10 11 11.5 12 14 10 11 11.5 12 14 10 11 11.5 12 14 10 11 11.5 12 14 10 11 11.5 12 14
TA3
C C C C C C C C C C C C C C C I I I I I I I I I I I I I I I
Status
Not Available
Not Available
Not Available
Notes: 1. Customers requiring delivery in Tape and Reel should add the character “T” to the end of the part number. Example: GS880LF18TT. 2. The speed column indicates the cycle frequency (Mhz) of the device in Pipelined mode and the latency (ns) in Flow Through mode. Each device is Pipeline / Flow through mode selectable by the user. 3. TA = C = Commercial Temperature Range. TA = I = Industrial Temperature Range. 4. GSI offers other versions this type of device in many different configurations and with a variety of different features, only some of which are covered in this data sheet. See the GSI Technology web site for a complete listing of current offerings. Rev: 1.03 3/2000 24/25 © 2000, Giga Semiconductor, Inc.
N
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
Preliminary GS880F18/36T-10/11/11.5/12/14 Revision History
DS/DateRev. Code: Old;
New
Types of Changes Format or Content
Content
Page;Revisions;Reason
• First Release of 880 F. • Changed Flow Through Read-Write Cycle Timing Diagram for accuracy. • Changed order of TQFP Address Inputs to match pinout. • Changed order of TQFP DATA Input and Output pins to match pinout. • New GSI Logo. • Changed all speed bin information (headings, references, tables, ordering info..) to reflect 14 -10Mhz
GS880F18/361.00 11/1999J GS880F18/36T1.00 K880F18/36T1.02 1/2000L
GS880F1836T Rev. 1.02 1/2000L; GS880F1836T Rev. 1.03 3/2000N
Content
Content
Rev: 1.03 3/2000
25/25
© 2000, Giga Semiconductor, Inc.
N
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.