C7044

IMAGE SENSOR CCD multichannel detector head C7043, C7044 Designed for back-thinned CCD area image sensor C7043 and C7044 are high sensitivity multichannel detector heads for use with back-thinned FFT-CCD area image sensors (S7033/S7034 series) that offer large full well capacity. C7043 is designed for the non-cooled back-thinned CCD image sensor (S7033 series), while C7044 for the onestage TE-cooled CCD area image sensors (S7034 series) for detection at even lower light levels. Both C7043 and C7044 incorporate a low-noise driver/amplifier circuit that provides reliable operation from simple external signals. C7044 also includes a highly stable temperature controller that cools the sensor to a preset temperature level (Ts= -10 ˚C) as soon as the power is turned on. If the cooler fails and causes internal circuitry to overheat, the built-in protection circuit automatically turns off the power to the thermoelectric cooler. Despite its compact size, the housing configuration is designed for good heat dissipation, and threaded mounting holes on the front panel allow connections to other devices such as monochrometers. The table below shows back-thinned CCD image sensors for C7043 and C7044. C7043 and C7044 do not come with a CCD image sensor, so select the desired sensor and order it separately. Controller for multichannel detector head C7557 is also available. The software supplied with the C7557 allows easy control of the multichannel detector head and data acquisition. Features Applications l Designed for back-thinned CCD area image sensor *1 C7043: for non-cooled type, C7044: for TE-cooled type l Line binning operation *2/area scanning operation l Driver/amplifier circuit for low noise CCD operation l Highly stable temperature controller (C7044) Cooling temperature: -10 ± 0.05 ˚C l Simple signal input operation l Compact configuration s Selection guide l Fluorescence spectroscopy l Raman spectroscopy l Other low-light-level detection The table below shows CCD area image sensors applicable for C7043, C7044. Since C7043, C7044 do not include a CCD area image sensor, so select the desired sensor and order it separately. CCD Area image sensor Type No. Type No. Number of pixels Number of active pixels Active area [mm (H) × mm (V)] S7033-0907 532 × 128 512 × 122 12.288 × 2.928 C7043 S7033-1007 1044 × 128 1024 × 122 24.576 × 2.928 S7034-0907 532 × 128 512 × 122 12.288 × 2.928 C7044 S7034-1007 1044 × 128 1024 × 122 24.576 × 2.928 *1: In normal CCD image sensors that receive light from the front surface, the active area is covered with electrodes for charge transfer. These electrodes cut off UV radiation incident on the image sensor and also reduce the quantum efficiency. In contrast, back-thinned CCD image sensors have a unique structure in which the back of the active area is finely ground to allow light to enter from the back surface. This structure ensures high UV sensitivity and quantum efficiency because incident light need not pass through the electrodes. *2: The FFT-CCD was originally designed as a two-dimensional image sensor. However, it can be operated like a linear image sensor having a large active area by transferring all the pixel signals in the vertical direction to the horizontal register (this is referred to as line binning). 1 CCD multichannel detector head s Absolute maximum ratings Parameter Supply voltage (for digital circuitry) Supply voltage (for analog circuitry) Supply voltage Digital input voltage Operating temperature Storage temperature C7043 C7044 C7043 C7044 Symbol VD1, VD2 VA1+ VA1VA2 Vp VF Topr Tstg Min. -0.5 0 +10 -20 0 Typ. - C7043, C7044 Max. +7 +18 -18 +30 +8 +14 VD1 +50 +35 *3 +70 +50 Unit V °C s Electrical characteristics (Ta=25 °C, VD1=+5 V, VA1+=+15 V, VA1-= -15 V, VA2=+24 V, VD2=+5 V, Vp=+5 V, VF=+12 V, unless otherwise noted) Parameter Digital input CLK frequency Data video readout frequency Start pulse width Digital output Power supply operating conditions Digital circuitry Analog circuitry Voltage Other *4 VD1 (+5 VDC) VA1+ (+15 VDC) VA1- (-15 VDC) VA2 (+24 VDC) VD2 (+6 VDC) *4 Vp (+6 VDC) *4 VF (+12 VDC) *4 VD1 VA1+ VA1VA2 VD2 Vp VF +4.75 +14.5 -14.5 +23.5 +4.75 +4.75 +11.75 +5.0 +15.0 -15.0 +24.0 +5.0 +5.0 +12.0 +100 +5.25 +15.5 -15.5 +24.5 +5.25 +5.25 +12.75 +200 +100 -100 +30 +30 +2.5 V V V V V V V mA mA mA mA mA A mA High level (IO= -6 mA) Low level (IO=+6 mA) High level Low level Symbol VIH VIL fCLK fv tst VIH VIL Min. +2.0 -0.5 1/fCLK +2.0 Typ. Max. VD (1, 2) +0.8 1 fCLK/4 +0.8 Unit V V MHz Hz s V V Current s Electrical and optical characteristics (Ta=25 °C, Ts= -10 °C, VD1=+5 V, VA1+=+15 V, VA1-= -15 V, VA2=+24 V, VD2=+5 V, Vp=+5 V, VF=+12 V) Min. Typ. Max. 200 to 1100 Vertical 300000 Full well capacity Fw Horizontal 2700000 Conversion gain *5 Sv 3 C7043 DS 4000 12000 Dark current *6 C7044 DS 50 300 Readout noise Nr 60 Dynamic range DR 45000 Photo response non-uniformity *7 PRNU ±10 *3: The maximum value may be lower, depending on the drive frequency and the number of sensor pixels. *4: C7044 *5: Including the circuit gain. *6: Horizontal register value. *7: Measured at 50 % of the full well capacity. Spectral response range Parameter Symbol SR Unit nm e - µV/e e /pixel/s e /pixel/s e rms % 2 CCD multichannel detector head C7043, C7044 s Specifications for temperature controller (C7044) (Ta=25 °C, VD1=+5 V, VA1+=+15 V, VA1-= -15 V, VA2=+24 V, VD2=+5 V, Vp=+5 V, VF=+12 V) Parameter *8 Symbol Min. Typ. Max. Unit Cooling temperature Ts -11 -10 -9 °C Temperature control range -0.05 +0.05 °C ∆Ts Power dissipation of TE-cooler element Pp 7 W Cool down time to reset temperature to 5 min. Setting temperature for overheat protection *9 To +45 °C *8: Other functions include error display, automatic power off, and detection of electrical opens and shorts by the thermosensor. *9: Temperature of rear-side of housing (part to fix fan) s Spectral response (Typ. Ta=25 ˚C) s Dark signal vs. temperature (Typ.) 100 90 10000 QUANTUM EFFICIENCY (%) 70 60 50 40 30 20 10 0 200 400 600 800 1000 1200 FRONT ILLUMINATED TYPES DARK SIGNAL (e-/pixel/s) 80 BACK THINNED TYPES 1000 100 10 1 0.1 -50 -40 -30 -20 -10 0 10 20 30 WAVELENGTH (nm) KMPDB0038EA TEMPERATURE (˚C) KMPDB0037EB s Block diagram (back-thinned CCD area image sensor) THINNING 22 23 21 20 15 14 13 2 BEVEL V 1 12 11 2 V=122 H=512, 1024 3 4 5 8 9 10 4 BLANK 2 SIGNAL OUT n 4 BLANK 6 BEVEL 6 BEVEL KMPDC0076EA n 24 5 4 3 2 12345 H 4 BEVEL 2 SIGNAL OUT THINNING 3 CCD multichannel detector head s Block diagram (C7044) C7043, C7044 P+ PLED TEMPERATURE CONTROLLER * Vp (+5 V) P. GND VD2 (+5 V) D. GND TH+ THVF (+12 V) F. GND Temp Monitor Cooling Control VD1 (+5 V) D. GND VA1+ (+15 V) VA1- (-15 V) A. GND VA2 (+24 V) Start CLK TIMING GENERATOR EOS Trigger Mode Select BUFFER Data Video PRE-AMP INVERTER CLAMP LOW-PASS FILTER TE-COOLER OD RD OG IG1H, IG2H IG1V, IG2V P1V, P2V, TG P1H, P2H SG RG SS, ISV, ISH OS REGULATOR TH.H VDD VEE DRIVER CCD AREA IMAGE SENSOR S7034 SERIES * C7043 does not include the temperature controller and TE-cooler. KACCC0114EB s Timing chart (line binning operation) Start CLK P1V P2V TG P1H P2H SG RG Clamp EOS Trigger Data Video V-ch1 V-ch2 V-ch(M) H-ch1 H-ch2 H-ch10 H-ch11 H-ch(N-10) H-ch(N-9) H-ch(N) M=128 N=532, 1044 V-ch1--V-ch2, V-ch (M-3)--V-ch (M): ISOLATION PIXELS H-ch1--H-ch4, H-ch (N-3)--H-ch (N): BLANK PIXELS KACCC0115EC 4 CCD multichannel detector head s Pin connection of "SIGNAL I/O" connector 15-pin D-sub connector C7043, C7044 8 7 6 5 4 3 2 1 15 14 13 12 11 10 9 KACCC0069EA Pin No. Terminal name 1 Mode select 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Data video VA1+ (+15 V) VA1- (-15 V) VD1 (+5 V) Start CLK EOS A. GND A. GND VA2 (+24 V) D. GND D. GND D. GND Trigger Description Digital input signal used to select between the line binning operation and area scanning operation. HCMOS compatible. High level or left open: line binning operation Low level: area scanning operation Analog video output. Positive polarity Analog power supply Analog power supply Digital power supply Digital input signal for initializing the circuit. HCMOS compatible. Positive logic. The interval of the Start pulses determines the integration time of the CCD image sensor. Digital input signal for operating the circuit. HCMOS compatible. Rising edge operation. Digital input signal for indicating end-of-scan of the image sensor. HCMOS compatible. Negative logic. Analog ground Analog ground Analog power supply Digital ground Digital ground Digital ground Digital output signal for A/D conversion. HCMOS compatible. Positive logic. s Pin connection of "TE CONTROL I/O" connector (C7044) 9-pin D-sub connector 5 4 3 2 1 9 8 7 6 KACCC0075EA Description Digital power supply Analog output signal of the temperature of the CCD image sensor Digital input signal for starting to cool down. HCMOS compatible. 3 Cooling control High level or left open: cooling Low level: stand-by 4 Vp (+5 V) Power supply for the thermoelectric cooler in the CCD image sensor. 5 VF (+12 V) Power supply for cooling fan 6 D. GND Ground for temperature control circuit 7 D. GND Ground for temperature control circuit 8 P. GND Power supply return of the thermoelectric cooler mounted in the CCD image sensor. 9 F. GND Power supply return for cooling fan Available for using same power supply (+5 V) for "+VD2" and "+Vp". Caution) Do not connect "VD2" and "Vp" together on the backside of the 9-pin D-sub connector. These may be connected (shorted) at the power supply end, not 9-pin D-sub connector. Pin No. 1 2 Terminal name VD2 (+5 V) Temp monitor 5 CCD multichannel detector head s Dimensional outlines (unit: mm) C7043 2.7 0.5 0.3 34.0 C7043, C7044 FOCAL PLANE 100.0 62.0 11.0 80.0 90.0 60.0 50.0 FOCAL PLANE 50.0 (4 ×) M3 DEPTH 4 82.0 KACCA0081EB C7044 35.0* 2.9 0.5 34.0 FOCAL PLANE 77.0 100.0 62.0 11.0 80.0 90.0 60.0 50.0 FOCAL PLANE 50.0 (4 ×) M3 DEPTH 4 *The part is removable. KACCA0082EB s Connection example TE CONTROLLER POWER SUPPLY VF (+12 V) F.GND VP (+5 V) P.GND VD2 (+5 V) D.GND CONTROLLER Cooling Control D.GND 9 8 3 7 6 2 1 5 4 I/O SIGNAL PULSE GENERATOR CLK D.GND Start D.GND VD1 (+5 V) D.GND VA1+ (+15 V) VA1- (-15 V) VA2 (+24 V) A.GND Mode Select D.GND Analog Input A.GND S/H Input D.GND CH1 GND Ext.Trig GND KACCC0076EB 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 POWER SUPPLY CONTROLLER S/H or A/D OSCILLOSCOPE 82.0 6 Cat. No. KACC1049E04 Dec. 2006 DN CCD multichannel detector head C7043, C7044 Multichannel detector head controller C7557 When connected to a HAMAMATSU multichannel detector head and a personal computer, C7557 allows easy control of the detector head and data acquisition by using dedicated software that comes with the unit. Suitable multichannel detector head C7020/-02, C7021/-02, C7025/-02, C7040, C7041, C7043, C7044, C7180, C7181, C8061-01, C8062-01, C10150, C10151 s Accessories · SCSI terminator · Fuse (2.5 A) · Detector head connection cables · AC cable · Software (Compatible OS: Windows 98/ME *) · Operation manual * This software may be run on Windows 2000/NT/XP with a simple task. For information on how to do this, please consult with our sales office. s Connection SHUTTER *1 TIMING PULSE Trig. POWER DEDICATED CABLE (WITH C7557) SIGNAL I/O SCSI *2 CABLE TE CONTROL I/O IMAGE SENSOR + MULTICHANNEL DETECTOR HEAD C7557 PC (Windows98/ME) (INTEGRATED SCSI BOARD) *1: Shutter, etc. are not available. *2: SCSI cable and SCSI board (card) are not supplied with C7557. KACCC0077ED Information furnished by HAMAMATSU is believed to be reliable. However, no responsibility is assumed for possible inaccuracies or omissions. Specifications are subject to change without notice. No patent rights are granted to any of the circuits described herein. ©2007 Hamamatsu Photonics K.K. HAMAMATSU PHOTONICS K.K., Solid State Division 1126-1 Ichino-cho, Higashi-ku, Hamamatsu City, 435-8558 Japan, Telephone: (81) 53-434-3311, Fax: (81) 53-434-5184, www.hamamatsu.com U.S.A.: Hamamatsu Corporation: 360 Foothill Road, P.O.Box 6910, Bridgewater, N.J. 08807-0910, U.S.A., Telephone: (1) 908-231-0960, Fax: (1) 908-231-1218 Germany: Hamamatsu Photonics Deutschland GmbH: Arzbergerstr. 10, D-82211 Herrsching am Ammersee, Germany, Telephone: (49) 08152-3750, Fax: (49) 08152-2658 France: Hamamatsu Photonics France S.A.R.L.: 19, Rue du Saule Trapu, Parc du Moulin de Massy, 91882 Massy Cedex, France, Telephone: 33-(1) 69 53 71 00, Fax: 33-(1) 69 53 71 10 United Kingdom: Hamamatsu Photonics UK Limited: 2 Howard Court, 10 Tewin Road, Welwyn Garden City, Hertfordshire AL7 1BW, United Kingdom, Telephone: (44) 1707-294888, Fax: (44) 1707-325777 North Europe: Hamamatsu Photonics Norden AB: Smidesvägen 12, SE-171 41 Solna, Sweden, Telephone: (46) 8-509-031-00, Fax: (46) 8-509-031-01 Italy: Hamamatsu Photonics Italia S.R.L.: Strada della Moia, 1/E, 20020 Arese, (Milano), Italy, Telephone: (39) 02-935-81-733, Fax: (39) 02-935-81-741 Cat. No. KACC1049E05 May 2007 DN 7