C7921CA-09

IMAGE SENSOR Flat panel sensor C7921CA-09 High resolution and high frame rate Flat panel sensor C7921CA-09 is a digital X-ray image sensor newly developed as key devices for non-destructive inspection, biochemical imaging, X-ray microscopy and other real-time X-ray imaging applications requiring high resolution and high image quality. Features Applications 4 frames/s (single binning) 16 frames/s (4 × 4 binning) l Wide dynamic range l High cost performance l High quality image: 1056 × 1056 pixels l Pixel size: 50 × 50 µm l Flat panel structure without image distortion l Digital output (12 bits) l High-speed imaging: l Non-destructive inspection l Digital X-ray photography s Block diagram C7921CA-09 is a lightweight and compact flat panel sensor consisting of a sensor board and a control board. The sensor board also has 8 charge-sensitive amplifier arrays each having 132 ch amplifiers with a horizontal shift register. Analog video signals are amplified as the charge on each video line by 1056 ch charge amplifiers with CDS (Correlated Double Sampling) circuits added, and are output each of 8 amplifier arrays. The control board converts the analog video signal into a 12-bit digital signal and outputs it to an external frame grabber through the 12-bit parallel port. PIXEL NUMBER 12 1057 1055 1056 2111 2112 VERTICAL SHIFT REGISTER EXTERNAL POWER SUPPLY A.vdd, D.vdd (not attached) SCINTILLATOR (52.8 × 52.8 mm) PHOTODIODE ARRAY IntExt BINNING (bin0, bin1) 1115135 AMP ARRAY No. 1 1115136 AMP ARRAY No. 8 TIMING PULSE GENERATOR BIAS GENERATOR BUFFER AMP BUFFER AMP PROCESSING AMP OSCILLATOR ExtTrgLemo ExtTrgGrb Vsync Hsync Pclk A/D FIFO VIDEO OUTPUT (12 BIT DIGITAL) PROCESSING AMP A/D FIFO KACCC0358EA Note: Signals are read out in order of pixel number. PRELIMINARY DATA Jan. 2007 1 Flat panel sensor s G eneral ratings Parameter Pixel size Photodiode area Number of pixels Number of active pixels Readout Video output (Data1 - 12) Output data rate Synchronous signal (Vsync, Hsync, Pclk) bin0/1, E xtTrgGrb, ExtTrgLemo, IntExt Scintillator Specification 50 × 50 52.8 × 52.8 1056 × 1056 1032 × 1012 Charge amplifier array RS-422 (differential) 12 bit 6.25 RS-422 (differential) TTL CsI C7921CA-09 Unit µm mm pixels pixels MHz - s A bsolute maximum ratings (Ta=25 °C) Parameter Supply voltage for digital circuitry (+5 V) Supply voltage for analog circuitry (+5 V) Input voltage (bin0/1, E xtTrg Grb, E xtTrgL e m o, IntE xt) Operating temperature *1 Storage temperature *1 *1: No condensation Symbol D.vdd A.vdd Vin Topr Tstg Value +6.0 +6.0 0 to 6.0 0 to +35 0 to +50 Unit V V V °C °C s S pecification (Ta=25 °C, A.vdd= 5.0 V, D.vdd= 5.0 V) Parameter Symbol Min. Typ. Max. Unit Frame rate (single operation) Sf (int) 3.8 4 frames/s Frame rate (2 × 2 binning) 8 frames/s Frame rate (4 × 4 binning) 16 frames/s Sf (int) to 0.1 Frame rate external (single operation) Sf (ext) frames/s Noise (rms) *2 N (rms) 1000 electrons Sensitivity *3 S 14.4 18 LSB/mR Saturation charge Csat 2.9 M electrons Resolution *4 Reso 7.1 8 line pairs/mm Dynamic range 2900 Defect line *5 10 lines Output offset *6 65 200 LSB *2: Internal trigger mode, single operation *3: At 80 kVp without filter *4: Spatial frequency at CTF=5 % *5: A defect line is a horizontal or vertical line containing 4 or more pixels that produce less than 1/8 of the average output from surrounding pixels and are formed continuously from the opposite side of an amplifier array or a vertical shift register. Without a couple of adjacent defect line. *6: Average of all effective pixels in single operation at Sf (int) Note: X-ray energy range is 20 k to 100 kVp. s Resolution 100 90 80 70 (Ta=25 ˚C, A.vdd=5.0 V, D.vdd=5.0 V) CTF (%) 60 50 40 30 20 10 0 0 1 2 3 4 5 6 7 8 9 10 SPATIAL FREQUENCY (line pairs/mm) KACCB0156EA 2 Flat panel sensor s Timing chart C7921CA-09 To acquire images through an image grabber board, write parameters in the software program or parameter file by referring to the following timing chart and description. 1 FRAME Vsync+ (GRABBER) 1st ROW 2nd ROW Hsync+ (GRABBER) He LAST ROW DUMMY LINES 1st ROW 2nd ROW All pulses are counted in the “High” period of Hsync+ ENLARGED VIEW Vsync+ (GRABBER) 1st ROW Hsync+ (GRABBER) Phe Pclk+ (GRABBER) Pg Phe Phd 2nd ROW Phe Phd All pulses are counted at the rising edge of Pclk+. The effective video output is only included in the “Phe” period. KACCC0362EA 1×1 Effective line 1012 He Dummy line 44 Effective pixel 1032 Phe Dummy pixel 25 Phd 366 Pg 17 Note: “He” is the Hsync count. Phe, Phd and Pg are the Pclk count. Parameter Pulse 2×2 506 22 516 13 894 17 4×4 253 11 258 7 1158 17 s External trigger mode To acquire images in external trigger mode, input an external trigger pulse as shown below. When the time Tvd has passed after the rising edge of the external trigger pulse, synchronous signals and video signals are output. From Tmin to Tmax RECOMMENDATION: 50 % OF FRAME TIME ExtTrgLemo ExtTrgGrb (TTL) Tvd Vsync+ (RS-422) Hsync+, Pclk+ and Data 1-12 are the same as internal trigger mode. · Tmin is defined as 1/Sf (int). · Tmax is defined as the reciprocal of the minimum value of Sf (ext). · Tvd=450 µs KACCC0363EA 3 Flat panel sensor s System requirements C7921CA-09 To operate C7921CA-09 at full performance, the following system and peripherals are required. · PC: IBM compatible PC running on Windows XP · Digital frame grabber card: Monochrome 16 bits or more, pixel clock 7 MHz or more, RS-422 interface synchronous signal (See the frame grabber manual.) The National Instruments IMAQ PCI-1424 (NI parts No. 777662-01) frame grabber has been verified to successfully acquire 12bit digital images from C7921CA-09. The IMAQ PCI-1422 (NI pats No. 777959-01) also acquires satisfactory images from C7921CA-09. You can utilize the demonstration software that comes with the frame grabber as a simple viewer, to acquire and save an image. To do so, refer to the frame grabber user’s guide for how to use the camera information file for the demonstration software. · Power source: A.vdd = +5.0 ± 0.1 V (700 mA), D.vdd = +5.0 ± 0.1 V (800 mA). Please use of a series power supply. (Avoid using a switching power supply.) A power cable (terminated with an FGG.2B.307.CLAD92Z plug at one end and open at the other end; 2 m; see Table 2.), an external trigger cable (terminated with an FFA.OS.302.CLAC37 plug at one end and open at the other end; 5 m; see table 3.) and an earth cable (AWG 18; 4 m) comes supplied with C7921CA-09. An optional frame grabber cable for interface with the 36-pin receptacle (see Table 1) on C7921CA09 is also available for synchronous signal, video output and external control. The voltages described above are specified at the flat panel sensor side. The impedance of the power cable attached with the flat panel sensor is low enough but it causes 0.1 V approx. drop. Therefore the voltage at the power source side should be set 0.1 V higher than the voltage specified above. Install a noise filter on the AC power input line to prevent surges on the AC line. To supply the synchronous signal through ExtTrgGrb, apply high level of TTL to ExtTrgLemo and IntExt, or leave them without connection. On the contrary, to use ExtTrgLemo, set high level to ExtTrgGrb and IntExt, or leave them without connection. The earth terminal must be connected to a stable earth point to eliminate noise from surroundings. Ta b le 1 : P in a s s ig n m e n t o f 3 6 -p in re c e p ta c le P in N o . S ig n a l P in N o . 1 D a ta 1 2 + (M S B ) 19 2 D a ta 11 + 20 3 D a ta 1 0 + 21 4 D a ta 9 + 22 5 D a ta 8 + 23 6 D a ta 7 + 24 7 D a ta 6 + 25 8 D a ta 5 + 26 9 D a ta 4 + 27 10 D a ta 3 + 28 11 D a ta 2 + 29 12 D a ta 1 + (L S B ) 30 13 b in 0 (T T L ) 31 14 b in 1 (T T L ) 32 15 E xtTrg G rb (T T L ) 33 16 V s yn c + 34 17 H s yn c + 35 18 P c lk + 36 U n le ss o th e rw is e n o te d , sig n a l le ve l is R S -4 2 2 . 3 6 -p in re ce p ta c le : T X 2 0 A -3 6 R -D 2 G F 1 -A 1 L m a d e b y J A E (J a p a n A via tio n E le c tro n ics In d u stry lim ite d ) M a tin g p lu g : T X 2 0 A -3 6 P H 1 -D 2 P 1 -D 1 E m a d e b y J A E (J a p a n A via tio n E le c tro n ic s In d u s try lim ite d ) S ig n a l D a ta 1 2 - (M S B ) D a ta 11 D a ta 1 0 D a ta 9 D a ta 8 D a ta 7 D a ta 6 D a ta 5 D a ta 4 D a ta 3 D a ta 2 D a ta 1 - (L S B ) GND GND In tE xt (T T L ) V s yn c H s yn c P c lk - Ta b le 2 : P o w e r p in a s s ig n m e n t a n d c a b le c o lo r P in N o . C o lo r 1 B ro w n 2 Red 3 O ra n g e 4 Ye llo w 5 G re e n 6 B lu e 7 P u rp le S h ie ld 7 -p in p o w e r re c e p ta c le : E C G .2 B .3 0 7 .C LV m a d e b y L E M O S . A . M a tin g p o w e r p lu g : F G G .2 B .3 0 7 .C L A D 9 2 Z m a d e b y L E M O S . A . P in N o . 1 to 3 a re n o t c o n n e cte d to th e e le c trica l c ircu it in sid e o f fla t p a n e l se n so r. T h e re fo re , p re vio u s p o w e r s o u rce a n d c a b le fo r C 7 9 2 1 C A -0 2 ca n b e u se d w ith o u t m o d ific a tio n . S ig n a l R e s e rve d R e s e rve d R e s e rve d A n a lo g G N D A n a lo g + 5 V D ig ita l G N D D ig ita l + 5 V A n a lo g G N D Ta b le 3 : E x te rn a l trig g e r p in a s s ig n m e n t a n d c a b le c o lo r P in N o . C o lo r 1 Red 2 B la ck S h ie ld 2 -p in re c e p ta c le : E C P.0 S .3 0 2 .C L L m a d e b y L E M O S . A . M a tin g p lu g : F FA .0 S .3 0 2 .C L A C 3 7 m a d e b y L E M O S . A . S ig n a l E xtTrg L e m o (T T L ) S ig n a l G N D A n a lo g G N D 4 Flat panel sensor s Connection C7921CA-09 Install the frame grabber board into the PC by the manufacturer’s instructions. When a general-purpose frame grabber board is used, binning or trigger operation for bin0, bin1, IntExt and ExtTrgGrb can be controlled with its digital I/O control. (REAR VIEW) PC/AT VIDEO OUTPUT FRAME (12 BIT DIGITAL) GRABBER Vsync, Hsync, Pclk OS + ACQUISITION SOFTWARE X-RAY SOURCE BINNING (bin0, bin1) IntExt ExtTrgGrb VOLTAGE SOURCE (A. vdd, D. vdd) MONITOR ExtTrgLemo CMOS FLAT PANEL SENSOR C7921CA-09 C7921CA-09 KACCC0354EA s Dimensional outline (unit: mm, tolerance: ±1 mm unless otherwise noted) SCINTILLATOR TO TOP COVER 9.3 * 142 33 30 10 11 * 108 * 17.1 * 33 ACTIVE AREA 50.6 (0, 0) (1031, 1011) EXT.TRG. POWER DIGITAL OUT 41 ACTIVE AREA 51.6 CMOS FLAT PANEL SENSOR C7921CA-09 12.4 118 * 142 50 (4 ×) M3 DEPTH 4 CMOS FLAT PANEL SENSOR C7921CA-09 13 Top cover is made of aluminum 1.0 mm thickness. Weight: 1.3 kg 15 17 24 96 * 29 * * ±0.5 KACCA0201EA 5 Flat panel sensor s Notice C7921CA-09 · Do not subject the Flat Panel Sensors to strong vibration or shock. (Strong shock such as drop impacts may cause permanent damage to these sensors.) · Users must take responsibility for implementing X-ray shielding safety measures to avoid the risk of X-ray exposure. · Data listed in this datasheet is defind at the time of shipment. Characteristics may vary somewhat due to exposure to X-rays so take proper countermeasures such as making periodic image correction. · This product is warranted for a period of 12 months after the date of the shipment. The warranty is limited to make a replacement or repair of any defective product due to defects in workmanship or materials used in manufacture. It does not cover loss or damage caused by natural disaster, misuse (including modifications and any use not complying with the environment, application, usage and storage conditions described in this datasheet), or total radiation dose over 1 million Roentgen (less than 100 kVp) even within the warranty period. · As described above, flat panel sensors have limited resistance to radiation. This must be taken into account when using a flat panel sensor under continuous irradiation (in-line non-destructive inspection, etc.) When using flat panel sensors in non-destructive inspection equipment, please contact us and provide information such as irradiation conditions. C7921CA-09 conforms to European EMC directives: EN61326 Class A. s Optional frame grabber cables Cable type No. Cable length Cable end A8406-31 5m A8406-36 7m General-purpose A8406-37 10 m A8406-38 12 m TX20A-36PH1-D2P1-D1E *8 A8406-32 5m A8406-33 7m IMAQ PCI-1424 *7 A8406-34 10 m A8406-35 12 m *7: Made by NI (National Instrument Corporation) *8: Made by JAE (Japan Aviation Electronics Industry, Limited) *9: Made by Honda Tsushin Kogyo Co. Ltd. Note: The detailed information for these optional cables is shown in the datasheet of A8406 series. Frame grabber Cable end open PCS-XE100MA+ *9 Information furnished by HAMAMATSU is believed to be reliable. However, no responsibility is assumed for possible inaccuracies or omissions. Specifications are subject to change without notice. No patent rights are granted to any of the circuits described herein. ©2007 Hamamatsu Photonics K.K. HAMAMATSU PHOTONICS K.K., Solid State Division 1126-1 Ichino-cho, Higashi-ku, Hamamatsu City, 435-8558 Japan, Telephone: (81) 53-434-3311, Fax: (81) 53-434-5184, www.hamamatsu.com U.S.A.: Hamamatsu Corporation: 360 Foothill Road, P.O.Box 6910, Bridgewater, N.J. 08807-0910, U.S.A., Telephone: (1) 908-231-0960, Fax: (1) 908-231-1218 Germany: Hamamatsu Photonics Deutschland GmbH: Arzbergerstr. 10, D-82211 Herrsching am Ammersee, Germany, Telephone: (49) 08152-3750, Fax: (49) 08152-2658 France: Hamamatsu Photonics France S.A.R.L.: 19, Rue du Saule Trapu, Parc du Moulin de Massy, 91882 Massy Cedex, France, Telephone: 33-(1) 69 53 71 00, Fax: 33-(1) 69 53 71 10 United Kingdom: Hamamatsu Photonics UK Limited: 2 Howard Court, 10 Tewin Road, Welwyn Garden City, Hertfordshire AL7 1BW, United Kingdom, Telephone: (44) 1707-294888, Fax: (44) 1707-325777 North Europe: Hamamatsu Photonics Norden AB: Smidesvägen 12, SE-171 41 Solna, Sweden, Telephone: (46) 8-509-031-00, Fax: (46) 8-509-031-01 Italy: Hamamatsu Photonics Italia S.R.L.: Strada della Moia, 1/E, 20020 Arese, (Milano), Italy, Telephone: (39) 02-935-81-733, Fax: (39) 02-935-81-741 Cat. No. KACC1138E03 6 May 2007 DN