H5784-06

Metal package PMT Photosensor Modules H5784 Series The H5784 series photosensor modules are comprised of a metal package photomultiplier tube, a low-power consumption high-voltage power supply and a low noise amplifier. The electrical current from the photomultiplier tube is converted to a voltage by an amplifier for easy signal processing. The H5784 is highly resistant to noise since the amplifier is installed near the anode output pin of the photomultiplier tube. The amplifier feedback resistance of 1 MΩ allows a current-to-voltage conversion factor of 1 V/µA, and covers a frequency bandwidth from DC to 20 kHz. Product Variations Type No. Spectral Response H5784 H5784-01 H5784-02 H5784-03 H5784-04 H5784-06 H5784-20 300 nm to 650 nm 300 nm to 850 nm 300 nm to 880 nm 185 nm to 650 nm 185 nm to 850 nm 185 nm to 650 nm 300 nm to 900 nm Current-to-voltage Frequency Conversion Factor Bandwidth Features For general applications in visible range For general applications in visible to near IR range High sensitivity in near IR range. DC to 20 kHz For UV to visible range For UV to near IR range For UV to visible range (synthetic silica window) with higher sensitivity below 300 nm than -03 type Infrared-extended multialkali photocathode with enhanced sensitivity 1 V/µA Specifications Parameter Suffix Input Voltage Max. Input Voltage Max. Input Current Max. Output Signal Voltage Max. Control Voltage Recommended Control Voltage Adjustment Range Effective Area Sensitivity Adjustment Range Peak Sensitivity Wavelength Min. Luminous Sensitivity Typ. Blue Sensitivity Index (CS 5-58) Red/White Ratio Radiant Sensitivity *1 Min. Luminous Sensitivity *2 Typ. Radiant Sensitivity *1 *2 Voltage Output Depending Typ. on PMT Dark Current *2 *3 Max. Current-to-Voltage Conversion Factor Typ. Offset Voltage *2 Ripple Noise *2 *4 (peak to peak) Max. Settling Time *5 Operating Ambient Temperature Storage Temperature Weight None/-03/-06 420 40 70 8 — 62 1.0 × 107 5.0 × 107 43 0.2 2 H5784 Series -01/-04 -02 ±11.5 to ±15.5 ±18 +9/-1 +10 (load resistance 10 kΩ) +1.0 (Input impedance 100 kΩ) +0.25 to +0.9 8 1: 104 400 500 80 200 150 250 — — 0.2 0.25 60 58 1.5 × 107 2.5 × 107 7.5 × 107 1.25 × 108 30 29 0.4 2 4 20 1 ±3 2 2 +5 to +50 -20 to +50 100 -20 630 350 500 — 0.45 78 3.5 × 107 2.5 × 108 39 2 20 Unit — V V mA V V V mm — nm µA/lm — — mA/W V/lm V/nW mV V/µA mV mV s °C °C g *1: Measured at the peak sensitivity wavelength *2: Control voltage = +0.8 V *3: After 30 minute storage in darkness *4: Cable RG-174/U, Cable length 450 mm, Load resistance = 1 MΩ, Load capacitance = 22 pF *5: The time required for the output to reach a stable level following a change in the control voltage from +1.0 V to +0.5 V. 28 Anode Cathode Voltage Output Type Photosensor Modules Characteristics (Anode radiant sensitivity, PMT gain) TPMOB0145EB PMT GAIN: 105 TPMOB0146EB PMT GAIN: 105 10 10 -04 Type -06 Type 108 TPMOB0114EB ANODE RADIANT SENSITIVITY (V/nW) ANODE RADIANT SENSITIVITY (V/nW) 107 -01 Type 1 106 None, -03, -06 Type 1 None Type PMT GAIN -20 Type -03 Type 105 -02 Type 0.1 -01, -02, -04, -20 Type 104 0.1 103 0.01 100 200 300 400 500 600 700 800 0.01 100 200 300 400 500 600 700 800 900 1000 102 0.25 0.3 0.4 0.5 0.7 1.0 1.2 1.5 2.0 WAVELENGTH (nm) WAVELENGTH (nm) CONTROL VOLTAGE (V) Sensitivity Adjustment Method Voltage Programming POWER SUPPLY SIGNAL OUTPUT +15 V -15 V Resistance Programming POWER SUPPLY SIGNAL OUTPUT +15 V -15 V PHOTOSENSOR MODULE LOW VOLTAGE INPUT LOW VOLTAGE INPUT GND Vref OUTPUT Vcontrol INPUT PHOTOSENSOR MODULE LOW VOLTAGE INPUT LOW VOLTAGE INPUT GND Vref OUTPUT Vcontrol INPUT 2 kΩ GND GND *1: When using a potentiometer to adjust sensitivity, monitor the control voltage so it does not exceed +1.0 V. +0.25 V to +0.9 V GND • Adjust the control voltage to adjust the sensitivity. • Electrically insulate the reference voltage output. MONITOR POTENTIOMETER (*1) (10 kΩ) TPMOC0154EC Dimensional Outlines (Unit: mm) 22.0 ± 0.5 14.0 ± 0.2 60.0 ± 0.5 1.5 ± 0.2 ("-06" Type: 0 ± 0.2) 450 ± 20 WINDOW 10 Vcc Low Voltage Input : AWG26 (Red, +15 V) Vee Low Voltage Input : AWG26 (Green, -15 V) : AWG26 (Black) GND : AWG26 (Blue, +1.2 V) Vref Output : AWG26 (White, +0.25 V to +0.9 V) Vcontrol Input : RG-174/U Signal output EFFECTIVE AREA 8 4-M2 DEPTH: 4 FRONT VIEW SIDE VIEW TPMOA0012EC Option (Optical Fiber Adapter) (Unit: mm) E5776 (FC Type) 22.0 ± 0.5 14.0 ± 0.2 8.5 3.5 ± 0.2 E5776-51 (SMA Type) 22.0 ± 0.5 14.0 ± 0.2 10.7 5.0 4-M2 FC-R 4-M2 SMA 3.0 FRONT VIEW SIDE VIEW TACCA0055EA FRONT VIEW SIDE VIEW TACCA0239EA 29