H7827-001_08

Photosensor Modules H7827 Series The H7827 series photosensor modules incorporate a 19-mm (3/4") diameter head-on photomultiplier tube, a high-voltage power supply circuit and a low noise amplifier. Two types of amplifiers are available with a current-to-voltage conversion factor of 1 V/µA or 0.1 V/µA and a frequency bandwidth of DC to 20 kHz or DC to 200 kHz. Two types of photomultiplier tubes with different spectral response characteristics are provided for measurement in the visible range or visible to near IR range. Product Variations Type No. H7827-001 H7827-011 H7827-002 H7827-012 Spectral Response Current-to-Voltage Conversion Factor Frequency Bandwidth 300 nm to 650 nm 1 V/µA DC to 20 kHz 300 nm to 850 nm 300 nm to 650 nm 0.1 V/µA DC to 200 kHz 300 nm to 850 nm Features For general applications in visible range For visible to near IR range For general applications in visible range For visible to near IR range Specifications Parameter Suffix Input Voltage Max. Input Voltage Max. Input Current Max. Control Voltage Recommended Control Voltage Adjustment Range Effective Area Sensitivity Adjustment Range Peak Sensitivity Wavelength Min. Luminous Sensitivity Typ. Blue Sensitivity Index (CS 5-58) Typ. Red/White Ratio Typ. Radiant Sensitivity *1 Typ. Suffix (with internal 20 kHz amp) Min. Luminous Sensitivity *2 Typ. Radiant Sensitivity *1 *2 Typ. Voltage Output Depending Typ. on PMT Dark Current *2 *3 *4 Max. Max. Output Signal Voltage Current-to-Voltage Conversion Factor Suffix (with internal 200 kHz amp) Min. Luminous Sensitivity *2 Typ. Radiant Sensitivity *1 *2 Typ. Voltage Output Depending Typ. on PMT Dark Current *2 *3 *4 Max. Max. Output Signal Voltage Current-to-Voltage Conversion Factor Cathode Anode Anode Offset Voltage Typ. Ripple Noise *2 *5 (peak to peak) Max. Settling Time *6 Max. Operating Ambient Temperature *7 Storage Temperature *7 Weight H7827 Series -001 / -002 -011 / -012 ±11.5 to ±15.5 ±18 +45/-1 (-001/-011), +50/-8 (-002/-012) +1.2 (Input Impedance 100 kΩ) +0.5 to +1.1 15 1: 103 380 420 80 60 120 90 — 10.5 0.2 — 49 85 -011 -001 1.0 × 107 1.0 × 107 3.0 × 107 5.0 × 107 13 47 3 3 20 20 +10 (Load resistance 10 kΩ) 1 -012 -002 1.0 × 106 1.0 × 106 3.0 × 106 5.0 × 106 1.3 4.7 0.3 0.3 2 2 +10 (Load resistance 10 kΩ) 0.1 H7827 series ±3 0.6 0.2 +5 to +45 -20 to +50 80 Unit — V V mA V V mm — nm µA/lm — — mA/W V/lm V/nW mV V V/µA V/lm V/nW mV V V/µA mV mV s °C °C g *1: Measured at the peak sensitivity wavelength *2: Control voltage = +1.0 V *3: After 30 minutes storage in darkness *4: Output of anode dark current *5: Cable RG-174/U, Cable length 450 mm, Load resistance = 1 MΩ, Load capacitance = 22 pF *6: The time required for the output to reach a stable level following a change in the control voltage from +1.0 V to +0.5 V *7: No condensation. HAMAMATSU PHOTONICS K.K. Characteristics (Anode radiant sensitivity, PMT gain) H7827-001 -011 10 TPMOB0156EA FEB. 2008 PMT GAIN: 105 1 -011 -012 H7827-002 -012 108 TPMOB0159EA ANODE RADIANT SENSITIVITY (V/nW) ANODE RADIANT SENSITIVITY (V/nW) 107 1 0.1 106 PMT GAIN -001 -002 105 -001 -002 0.1 0.01 104 -011 -012 103 0.01 100 200 300 400 500 600 700 800 0.001 900 102 0.25 0.3 0.4 0.5 0.7 1.0 1.2 1.5 WAVELENGTH (nm) CONTROL VOLTAGE (V) Sensitivity Adjustment Method VOLTAGE PROGRAMMING PHOTOSENSOR MODULE SIGNAL OUTPUT LOW VOLTAGE INPUT (RED) LOW VOLTAGE INPUT (GREEN) GND (BLACK) Vref OUTPUT (BLUE) Vcont INPUT (WHITE) POWER SUPPLY +15 V -15 V GND RESISTANCE PROGRAMMING PHOTOSENSOR MODULE SIGNAL OUTPUT LOW VOLTAGE INPUT (RED) LOW VOLTAGE INPUT (GREEN) GND (BLACK) Vref OUTPUT (BLUE) Vcont INPUT (WHITE) MONITOR POTENTIOMETER (10 kΩ) When using a potentiometer, adjust sensitivity while monitoring the control voltage. TPMOC0166EB POWER SUPPLY +15 V -15 V GND CW • Adjust the control voltage to adjust the sensitivity. • Electrically insulate the reference voltage output. +0.5 V to +1.1 V GND Dimensional Outlines (Unit: mm) 26.0 +0.5 -0 13.0 ± 0.5 EFFECTIVE AREA 15 MIN. 0 +0.1 -0.3 56.0 +0.5 -0 SIGNAL OUTPUT BNC-R 19.0 ± 0.5 18.0 ± 0.5 POWER INPUT HIROSE HR10A-7R-6P 1: GND 2: LOW VOLTAGE INPUT (+15 V) 3: Vcont INPUT (+0.5 V to +1.1 V) 4: Vref OUTPUT (+1.2 V) 5: NC 6: LOW VOLTAGE INPUT (-15 V) 50.0 +1.0 -0 14.0 ± 0.5 18 THREADED HOLE for OPTION (4-M2 DEPTH: 5) 10.0 ± 0.5 FRONT VIEW 16.0 ± 0.5 SIDE VIEW 25.0 ± 0.5 18.6 ± 0.7 MOUNTING THREADED HOLE (2-M3 DEPTH: 5) REAR VIEW Power cable with connector (HIROSE HR10A-7P-6S) is supplied with the H7827 series BLACK: RED: WHITE: BLUE: GREEN: GND LOW VOLTAGE INPUT (+15 V) Vcont INPUT (+0.5 V to +1.1 V) Vref OUTPUT (+1.2 V) LOW VOLTAGE INPUT (-15 V) 700 ± 20 TPMOA0023EB