H8249-001

Photosensor Modules H8249 Series The H8249 series photosensor modules incorporate a 28-mm (1-1/8") diameter side-on photomultiplier tube, a high-voltage power supply circuit and a low noise amplifier. Two types of amplifiers are available with a current-tovoltage conversion factor of 1 V/µA or 0.1 V/µA and a frequency bandwidth of DC to 20 kHz or DC to 200 kHz. Three types of photomultiplier tubes are provided as standard lineups for general applications in the visible range, UV to visible range requiring low-noise, and UV to near IR range. Product Variations Type No. Spectral Response Current-to-Voltage Frequency Bandwidth Features Conversion Factor For general applications in visible range H8249-001 300 nm to 650 nm For general applications in UV to visible range H8249-011 185 nm to 680 nm 1 V/µA DC to 20 kHz High sensitivity in UV to near IR range. Uses photomultiplier H8249-101 185 nm to 900 nm tube with meshless grid for excellent uniformity. For general applications in visible range H8249-002 300 nm to 650 nm For general applications in UV to visible range H8249-012 185 nm to 680 nm 0.1 V/µA DC to 200 kHz High sensitivity in UV to near IR range. Uses photomultiplier H8249-102 185 nm to 900 nm tube with meshless grid for excellent uniformity. Specifications Parameter Suffix Input Voltage Max. Input Voltage Max. Input Current Max. Control Voltage Recommended Control Voltage Adjustment Range Effective Area Sensitivity Adjustment Range Peak Sensitivity Wavelength Min. Luminous Sensitivity Typ. Blue Sensitivity Index (CS 5-58) Typ. Red/White Ratio Typ. Radiant Sensitivity *1 Typ. Suffix (with internal 20 kHz amp) Min. Luminous Sensitivity *2 Typ. Radiant Sensitivity *1 *2 Typ. Voltage Output Depending Typ. on PMT Dark Current *2 *3 *4 Max. Max. Output Signal Voltage Current-to-Voltage Conversion Factor Suffix (with internal 200 kHz amp) Min. Luminous Sensitivity *2 Typ. Radiant Sensitivity *1 *2 Typ. Voltage Output Depending Typ. on PMT Dark Current *2 *3 *4 Max. Max. Output Signal Voltage Current-to-Voltage Conversion Factor Cathode Anode Anode -001 / -002 Offset Voltage Typ. Ripple Noise *2 *5 (peak to peak) Max. Settling Time *6 Max. Operating Ambient Temperature *7 Storage Temperature *7 Weight H8249 Series -101 / -102 -011 / -012 ±11.5 to ±15.5 ±18 +45/-1 (-001/-011/-101), +55/-15 (-002/-012/-102) +1.2 (Input Impedance 100 kΩ) +0.3 to +1.1 4 × 20 1: 104 400 30 140 40 60 250 60 7.1 8.0 6.4 — 0.3 — 60 74 60 -001 -101 -011 5.0 × 107 4.0 × 108 2.0 × 108 8 6.0 × 108 2.5 × 109 4.0 × 10 600 740 400 5 3 0.1 50 50 2 +10 (Load resistance 10 kΩ) 1 -002 -102 -012 5.0 × 106 4.0 × 107 2.0 × 107 6.0 × 107 2.5 × 108 4.0 × 107 60 74 40 0.5 0.3 0.01 5 5 0.2 +10 (Load resistance 10 kΩ) 0.1 H8249 series ±3 0.6 0.2 +5 to +45 -20 to +50 220 Unit — V V mA V V mm — nm µA/lm — — mA/W V/lm V/nW mV V V/µA V/lm V/nW mV V V/µA mV mV s °C °C g *1: Measured at the peak sensitivity wavelength *2: Control voltage = +1.0 V *3: After 30 minutes storage in darkness *4: Output of anode dark current *5: Cable RG-174/U, Cable length 450 mm, Load resistance = 1 MΩ, Load capacitance = 22 pF *6: The time required for the output to reach a stable level following a change in the control voltage from +1.0 V to +0.5 V. *7: No condensation HAMAMATSU PHOTONICS K.K. Characteristics (Anode radiant sensitivity, PMT gain) H8249-001 -011 10 -101 TPMOB0155EA FEB. 2008 PMT GAIN: 105 1 -101 -102 H8249-002 -012 -102 108 TPMOB0158EA ANODE RADIANT SENSITIVITY (V/nW) -011 -012 1 0.1 ANODE RADIANT SENSITIVITY (V/nW) 107 -101 -102 106 -001 -002 105 -001 -002 0.1 0.01 PMT GAIN 104 -011 -012 103 0.01 100 200 300 400 500 600 700 800 0.001 900 102 0.25 0.3 0.4 0.5 0.7 1.0 1.2 1.5 WAVELENGTH (nm) CONTROL VOLTAGE (V) Sensitivity Adjustment Method VOLTAGE PROGRAMMING PHOTOSENSOR MODULE SIGNAL OUTPUT LOW VOLTAGE INPUT (RED) LOW VOLTAGE INPUT (GREEN) GND (BLACK) Vref OUTPUT (BLUE) Vcont INPUT (WHITE) POWER SUPPLY +15 V -15 V GND RESISTANCE PROGRAMMING PHOTOSENSOR MODULE SIGNAL OUTPUT LOW VOLTAGE INPUT (RED) LOW VOLTAGE INPUT (GREEN) GND (BLACK) Vref OUTPUT (BLUE) Vcont INPUT (WHITE) MONITOR POTENTIOMETER (10 kΩ) When using a potentiometer, adjust sensitivity while monitoring the control voltage. TPMOC0162ED POWER SUPPLY +15 V -15 V GND CW • Adjust the control voltage to adjust the sensitivity. • Electrically insulate the reference voltage output. +0.3 V to +1.1 V GND Dimensional Outlines (Unit: mm) 5.0 ± 0.5 38.0 ± 0.5 R3 27.0 ± 0.5 EFFECTIVE AREA (4 × 20) 50.0 ± 0.5 10.0 ± 0.5 POWER INPUT HIROSE HR10A-7R-6P 1: GND 2: LOW VOLTAGE INPUT (+15 V) 3: Vcont INPUT (+0.3 V to +1.1 V) 4: Vref OUTPUT (+1.2 V) 5: GND 6: LOW VOLTAGE INPUT (-15 V) 55.0 ± 0.5 DETAILS OF INPUT WINDOW +1.0 +0.5 2.5 - 0 1.5 -0 WINDOW 19.0 ± 0.5 24.0 +0.5 -0 23.0 ± 0.8 95.0 ± 1.0 85.0 ± 0.5 87.0 ± 0.5 55.0 ± 0.5 8.0 +0.5 -0 34.0 ± 0.8 17.2 ± 0.5 4.5 ± 0.3 8 WINDOW TOP VIEW MOUNTING THREADED HOLE (4-M3 DEPTH: 10) FRONT VIEW MOUNTING THREADED HOLE (2 × 2-M3 DEPTH: 10) SIDE VIEW SIGNAL OUTPUT BNC-R REAR VIEW PHOTOCATHODE FRONT VIEW TPMOC0123EC Power cable with connector (HIROSE HR10A-7P-6S) is supplied with the H8249 series BLACK: RED: WHITE: BLUE: GREEN: GND LOW VOLTAGE INPUT (+15 V) Vcont INPUT (+0.3 V to +1.1 V) Vref OUTPUT (+1.2 V) LOW VOLTAGE INPUT (-15 V) TPMOA0022EC 700 ± 20 20 -0 EFFECTIVE AREA (4 × 20) +2