H8711

MULTIANODE PHOTOMULTIPLIER TUBE ASSEMBLY H8711, H8711-10 PATENT 4 mm × 4 mm Multianode, High Speed Response, Low Cross-talk 30 mm Square, Bialkali Photocathode, 12-stage, Head-on Type GENERAL Parameter Spectral Response Peak Wavelength Photocathode Window Material Dynode Structure Number of Stages Material Minimum Effective Area Description/Value 300 to 650 420 Bialkali 18.1 × 18.1 Borosilicate glass Metal channel dynode 12 4.2 × 4.2 (center) Approx. 50 -30 to +50 -30 to +50 Unit nm nm — mm — — — mm g °C °C Anode Size Weight Operating Ambient Temperature Storage Temperature MAXIMUM RATINGS (Absolute Maximum Values) Parameter Supply Voltage Between Anode and Cathode Average Anode Output Current in Total Value 1000 0.014* Unit V mA * The maximum average anode current is defined as 5 % of divider current when standard high voltage is applied. CHARACTERISTICS (at 25 °C) Cathode Sensitivity Anode Sensitivity Gain Anode Dark Current per Channel (after 30 min storage in darkness) Anode Dark Current in Total (after 30 min storage in darkness) Anode Pulse Rise Time Time Response Electron Transit Time per Channel Transit Time Spread (FWHM) Pulse Linearity per Channel (±5 % deviation) Cross-talk (4 mm × 4 mm Aperture) Uniformity Between Each Anode Parameter Luminous (2856 K) Blue Sensitivity Index (CS 5-58) Luminous (2856 K) Min. 60 6.5 80 (20) — — — — — — — — — Typ. 80 8.5 280 (70) 3.5 × 106 (0.9 × 106) 0.8 (0.4) 12 (6) 0.83 10.9 0.3 1 (3) 1 1: 3 Max. — — — — — 60 (30) — — — — — 1: 5 Unit µA/lm — A/lm — nA nA ns ns ns mA % — NOTE: Anode characteristics are measured with the voltage distribution ratio shown below. ( ): Measured with the special voltage distribution ratio (Tapered Divider) shown below. VOLTAGE DISTRIBUTION RATIO AND SUPPLY VOLTAGE Electrodes K Dy1 Dy2 Dy3 Dy4 Dy5 H8711 2 2 2 1 1 H8711-10 (Tapered Divider) 2.4 2.4 2.4 1 1 Supply Voltage: 800 V, K: Cathode, Dy: Dynode, P: Anode ... 1 ... 1 1 ... 1 Dy9 1 1 Dy10 1 1 Dy11 Dy12 P 1 1 1.2 2.4 Subject to local technical requirements and regulations, availability of products included in this promotional material may vary. Please consult with our sales office. Information furnished by HAMAMATSU is believed to be reliable. However, no responsibility is assumed for possible inaccuracies or omissions. Specifications are subject to change without notice. No patent rights are granted to any of the circuits described herein. ©2003 Hamamatsu Photonics K.K. MULTIANODE PHOTOMULTIPLIER TUBE ASSEMBLIES H8711, H8711-10 Figure 1: Typical Spectral Response TPMHB0266EA Figure 2: Typical Gain and Anode Dark Current per Channel 108 TPMHB0690EA 100 CATHODE RADIANT SENSITIVITY 10 104 CATHODE RADIANT SENSITIVITY (mA/W) QUANTUM EFFICIENCY (%) 107 103 106 QUANTUM EFFICIENCY GAIN 105 7 H8 11 102 0 1 GAIN H 1 87 1 1− 101 104 H 11 87 100 −1 11 0 103 0.1 102 7 H8 10-1 ANODE DARK CURRENT PER CHANNEL 10-2 0.01 100 200 300 400 500 600 700 800 900 101 400 600 800 10-3 1000 WAVELENGTH (nm) SUPPLY VOLTAGE (V) Figure 3: Typical Time Response TPMHB0331EA Figure 4: Typical T.T.S. Characteristic TPMHB0314EB 104 SUPPLY VOLTAGE= - 800 V FWHM= 310 ps FWTM= 631 ps RELATIVE COUNTS 103 (2 mV/div.) SUPPLY VOLTAGE = -800 V RISE TIME = 835 ps FALL TIME = 2047 ps WIDTH = 1658 ps RL = 50 Ω 102 101 100 TIME (2 ns/div.) TIME (0.5 ns/div.) ANODE DARK CURRENT (nA) Figure 5: Pulse Linearity per Channel 10 TPMHB0691EA 10 TPMHB0692EA PULSE WIDTH= 50 ns REPETITION= 1 kHz SUPPLY VOLTAGE= -800 V PULSE WIDTH= 50 ns REPETITION= 1 kHz SUPPLY VOLTAGE= -800 V DEVIATION (%) Divider Ratio 2:2:2 :1:⋅⋅⋅⋅:1:1:1 DEVIATION (%) 0 0 Divider Ratio 2.4 : 2.4 : 2.4 : 1 : ⋅ ⋅ ⋅ ⋅ : 1 : 1.2 : 2.4 -10 -10 -20 10-2 10-1 100 101 -20 10-2 10-1 100 101 OUTPUT CURRENT (mA) OUTPUT CURRENT (mA) H8711 H8711-10 Figure 6: Anode Uniformity (Example) 92 62 64 79 73 52 53 81 76 50 51 81 90 69 72 100 Figure 7: Anode Cross-talk (Example) 0.1 0.5 0.1 * 0.8 100 0.3 * 0.1 0.3 0.1 * * * * * Supply Voltage: 800 V Light Source: Tungsten Lamp (uniform DC light) Full Illumination Supply Voltage: 800 V Light Source: Tungsten Lamp (uniform DC light) Spot Illumination: 4 mm × 4 mm MULTIANODE PHOTOMULTIPLIER TUBE ASSEMBLIES H8711, H8711-10 Figure 8: Dimensional Outline and Circuit Diagram (Unit: mm) 9.3 8.7 0.3 4 3 2 1 POM CASE 4- 0.3 GUIDE MARKS 0.3 INSULATING TAPE DIVIDER ASSEMBLY 2.54 7.62 DY 12.7 GND -HV 4-SCREWS (M2) 30 ± 0.5 25.7 18.1 P1 P8 8.7 9.3 P9 P16 2.54 16 15 14 13 5.08 GND 4.5 18.1 25.7 GUIDE MARK 3 2 4.5 1 MAX. 45 ± 1 3.2 3.7 GND DY12 OUTPUT 2.54 2.54 × 7=17.78 THROUGH HOLE (NO CONNECTION) -HV INPUT NOTE 2 -HV TERMINAL PINS ( 0.46) ; BBL-TYPE, SAMTEC NOTE 3 DY12 OUTPUT TERMINAL PINS ( 0.46) ; BBL-102, SAMTEC * Suitable sockets for all terminal pins are attached. NOTE 1 The suitable socket for anode output terminal pins is "SD-108-T-22 (SAMTEC U.S.A)" which is commercially available. NOTE 2 The suitable socket for hight voltage terminal pins is "SS-102-T-22 (SAMTEC U.S.A)" which is commercially available. NOTE 3 The suitable socket for DY12 output terminal pins is "ASP-24307-02 (SAMTEC U.S.A)" which is commercially available. NOTE 1 0.65 Y ANODE OUTPUTS (P1 to P8) TERMINAL PINS ( 0.46) ; BDL-108, SAMTEC PIN CONNECTION P1 P2 P3 P4 P5 P6 P7 P8 GND GND GND GND GND GND GND GND X ANODE OUTPUTS (P9 to P16) P9 P10 P11 P12 P13 P14 P15 P16 TERMINAL PINS ( 0.46) GND GND GND GND GND GND GND GND ; BDL-108, SAMTEC H8711 TERMINAL PINS (BDL-108, SAMTEC) R1 to R3 : 360 kΩ R4 to R13 : 180 kΩ R14 : 1 MΩ R15 to R17 : 51 Ω R18 : 10 kΩ C1 to C4 : 0.01 µF F DY1 DY2 DY3 DY4 DY5 DY6 DY7 DY8 DY9 DY10 DY11 DY12 P1 P2 ANODE1 OUTPUT ANODE2 OUTPUT ANODE8 OUTPUT GND GND GND P8 P9 K TERMINAL PINS (BDL-108, SAMTEC) ANODE9 OUTPUT GND GND GND P15 P16 C4 ANODE15 OUTPUT ANODE16 OUTPUT R14 R1 R2 R3 R4 R5 R6 R7 R8 R9 R10 R15 R11 C1 R16 R12 C2 R17 R13 C3 R18 TERMINAL PINS (BBL-102, SAMTEC) DY12 OUTPUT GND TERMINAL PINS (BBL-TYPE, SAMTEC) -HV INPUT GND TPMHA0496EA *NOTE: DIVIDER RATIO=2:2:2:1:1...1:1:1 H8711-10 TERMINAL PINS (BDL-108, SAMTEC) R1 to R3, R13 : 360 kΩ R4 to R11 : 150 kΩ R12 : 180 kΩ R14 : 1 MΩ R15 to R17 : 51 Ω R18 : 10 kΩ C1 to C4 : 0.01 µF P1 P2 ANODE1 OUTPUT ANODE2 OUTPUT ANODE8 OUTPUT GND GND GND P8 P9 K F TERMINAL PINS (BDL-108, SAMTEC) ANODE9 OUTPUT GND GND GND DY1 DY2 DY3 DY4 DY5 DY6 DY7 DY8 DY9 DY10 DY11 DY12 P15 P16 C4 ANODE15 OUTPUT ANODE16 OUTPUT R14 R1 R2 R3 R4 R5 R6 R7 R8 R9 R10 R15 R11 C1 R16 R12 C2 R17 R13 C3 R18 TERMINAL PINS (BBL-102, SAMTEC) DY12 OUTPUT GND TERMINAL PINS (BBL-TYPE, SAMTEC) -HV INPUT GND TPMHA0497EA *NOTE: DIVIDER RATIO=2.4:2.4:2.4:1:1...1:1.2:2.4 WARNING ~ High Voltage ~ The product is operated at high voltage potential. Further, the metal housing of the product is connected to the photocathode (potential) so that it becomes a high voltage potential when the product is operated at a negative high voltage (anode grounded). Accordingly, extreme safety care must be taken for the electrical shock hazard to the operator or the damage to the other instruments. * PATENT: USA Pat. No. 5410211 PATENTE PENDING: JAPAN 11, USA 1, EUROPE 2 WEB SITE http://www.hamamatsu.com HAMAMATSU PHOTONICS K.K., Electron Tube Center 314-5, Shimokanzo, Toyooka-village, Iwata-gun, Shizuoka-ken, 438-0193, Japan, Telephone: (81)539/62-5248, Fax: (81)539/62-2205 U.S.A.: Hamamatsu Corporation: 360 Foothill Road, P. O. Box 6910, Bridgewater. N.J. 08807-0910, U.S.A., Telephone: (1)908-231-0960, Fax: (1)908-231-1218 E-mail: usa@hamamatsu.com Germany: Hamamatsu Photonics Deutschland GmbH: Arzbergerstr. 10, D-82211 Herrsching am Ammersee, Germany, Telephone: (49)8152-375-0, Fax: (49)8152-2658 E-mail: info@hamamatsu.de France: Hamamatsu Photonics France S.A.R.L.: 8, Rue du Saule Trapu, Parc du Moulin de Massy, 91882 Massy Cedex, France, Telephone: (33)1 69 53 71 00, Fax: (33)1 69 53 71 10 E-mail: infos@hamamatsu.fr United Kingdom: Hamamatsu Photonics UK Limited: 2 Howard Court, 10 Tewin Road Welwyn Garden City Hertfordshire AL7 1BW, United Kingdom, Telephone: 44-(0)1707-294888, Fax: 44(0)1707-325777 E-mail: info@hamamatsu.co.uk North Europe: Hamamatsu Photonics Norden AB: Smidesvägen 12, SE-171-41 SOLNA, Sweden, Telephone: (46)8-509-031-00, Fax: (46)8-509-031-01 E-mail: info@hamamatsu.se Italy: Hamamatsu Photonics Italia: S.R.L.: Strada della Moia, 1/E, 20020 Arese, (Milano), Italy, Telephone: (39)02-935 81 733, Fax: (39)02-935 81 741 E-mail: info@hamamatsu.it TPMH1278E02 APR. 2003 IP