0160002.MR

Surface Mount Fuses NANO2® > 160 Fuse and Clip Series 160 Series Fuse and Clip Assembly Description The 160 Series product is a metal fuse clip with preinstalled Littelfuse 443 Series Fuse. This fuse and clip combination can be automatically installed in PC Boards in one efficient manufacturing operation. It permits quick and easy fuse replacement without exposing the PC Boards and other components to risks of rework solder heat as required with direct surface mount fuses. It is designed to enable compliance with the RoHS directive. This product is fully compatible with lead-free solder alloy and higher temperature profiles associated with lead-free assembly. Features Agency Approvals Agency Agency File Number Ampere Range E14721 0.5A - 5A Electrical Characteristics for Series % of Ampere Rating Opening Time 100% 4 hours, Minimum 250% 120 seconds, Maximum • Offer low profile easily-replaceable fuse alternative compatible with automated PCB surface mount equipment • Come supplied with Littelfuse 443 Series Time-Lag 250V Nano2® Fuse • Telecom equipment system power Datasheet Resources Samples • Clip fully compatible with RoHS/lead-free solder alloys and higher temperature profiles associated with lead-free assembly • 0.5A - 5A ampere rating available Applications • AC/DC power adaptor Additional Information • RoHS compliant and Halogen Free • Portable system built-in AC/DC converter • High voltage DC/DC converter • Lighting System • LED Lighting Electrical Specifications by Item Ampere Rating (A) Amp Code Max Voltage Rating (V) 0.50 0.50 0.75 1.00 Agency Approvals Nominal Cold Resistance (Ohms) Nominal Melting I2t (A2sec) Nominal Voltage Drop (mV) 250 .5974 1.96 334 X 0.75 250 .2729 2.25 223 X 001. 250 .1826 9.00 207 X 1.50 01.5 250 .1100 15.21 210 X 2.00 002. 250 .0511 18.50 117 X .0392 22.20 156 X .0276 59.29 103 X 2.50 02.5 250 3.00 003. 250 Interrupting Rating 50 A @ 250 VAC 3.50 03.5 250 .0199 59.34 87 X 4.00 004. 250 .0160 68.10 83 X 5.00 005. 250 .0115 122.39 73 X Notes: 1. Cold resistance measured at less than 10% of rated current at 23°C. 2. Agency Approval Table Key: X=Approved or Certified, P=Pending. © 2013 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 12/19/13 Surface Mount Fuses NANO2® > 160 Fuse and Clip Series 5A 2A 2.5A 3A 3.5A 4A .750A 1A 1.5A Average Time Current Curves .500A Temperature Rerating Curve 100 TIME IN SECONDS 10 1 0.1 0.01 0.001 0.1 1 10 100 1000 CURRENT IN AMPS Soldering Parameters Pre Heat Pb-free assembly - Temperature Min (Ts(min)) 150°C - Temperature Max (Ts(max)) 200°C - Time (Min to Max) (ts) 60 – 180 seconds TL 5°C/second max. TS(max) to TL - Ramp-up Rate 5°C/second max. - Temperature (TL) (Liquidus) 217°C - Temperature (tL) 60 – 150 seconds 260 Time within 5°C of actual peak Temperature (tp) 20 – 40 seconds tL TSmax TSmin tS Ramp-down Preheat 25 Peak Temperature (TP) +0/–5 Critical Zone TL to TP Ramp-up Average Ramp-up Rate (Liquidus Temp (TL) to peak) Reflow tP TP Temperature Reflow Condition t 25ºC to Peak Time °C Ramp-down Rate 5°C/second max. Time 25°C to peak Temperature (TP) 8 minutes max. Do not exceed 260°C © 2013 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 12/19/13 Surface Mount Fuses NANO2® > 160 Fuse and Clip Series Product Characteristics Materials Body: Ceramic Cap: Silver-plated Brass Operating Temperature –55°C to 125°C with proper rerating Product Marking Brand, Ampere Rating, Voltage Rating, UMF Logo Thermal Shock MIL-STD-202F, Method 107G, Test Condition B (5 cycles, -65°C to 125°C) Vibration MIL-STD-202F, Method 201A (10-55 Hz) Moisture Resistance MIL-STD-202, Method 106, High Humidity (90-98%RH), Heat (65°C) Salt Spray MIL-STD-202F, Method 101D, Test Condition B Mechanical Shock MIL-STD-202, Method 213, Test Condition I (100 G’s peak for 6 msecs.) Insulation Resistance MIL-STD-202, Method 302, Test Condition A (10,000 ohms, (after Opening) Minimum) Solderability MIL-STD-202, Method 208 Resistance to Soldering Heat MIL-STD-202, Method 210, Test Condition B (10 seconds at 260°C) Moisture Sensitivity Level Level 1 J-STD-020C Part Numbering System Dimensions 10.90 [0.429] 10.10 [0.398] 160 01.5 M R 3.12 [0.123] 1.5AT AC250V SERIES 4.80 [0.189] 3.50 [0.138] 3.12 [0.123] LF Amp Code Refer to Electrical Specifications table 1.70 [0.067] 3.00 [0.118] 4.80 [0.189] 4.00 [0.157] 4.80 [0.189] Quantity code M = 1000 pcs packaging code R = Tape and Reel Example: 1.5 amp product is 016001.5 MR 4.90 [0.193] “A” .004 “B” Recommended Pad Layout 4.40 [0.173] 4.30 [0.169] 3.88 [0.153] 13.00 [0.512] Packaging Form Factor Packaging Option Packaging Specification Quantity Quantity & Packaging Code Surface Mount 24mm Tape and Reel EIA-RS 481-2 (IEC 286, part 3) 1000 MR © 2013 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 12/19/13