0216.050MRET1P

Axial Lead & Cartridge Fuses 5×20 mm > Fast-Acting > 216 Series 216 Series, 5×20 mm, Fast-Acting Fuse RoHS Pb PS E Description The 216 Series is a 5x20mm, Fast-Acting, ceramic body, cartridge fuse designed to IEC specifications Features • Recognized to UL/CSA/ NMX 248-1 and UL/CSA/ NMX 248-14 • Meets Standard Sheet 1 of IEC 60127-2 as a FastActing fuse • Available in cartridge and axial lead form Agency Approvals Agency PS E • Conforms to GB 9364.1 and GB 9364.2 • CE Mark indicates compliance with LowVoltage and RoHS Directives. Applications Agency File Number Cartridge 216 Series NBK 080205-E10480A NBK 250702-E10480E NBK 240108-JP1021C NBK 240108-JP1021E Leaded 216E Series NBK 080205-E10480B NBK 250702-E10480F NBK 240108-JP1021D NBK 240108-JP1021F 2020970207000066 SU05001-2013 E10480 29862 *Approval for Cartridge versions only • RoHS compliant and lead-free Ampere Range 1A-5A 6.3A-10A 12.5A 16A 1A-5A 6.3A-10A 12.5A 16A 0.05A-10A Used as supplementary protection in appliance or utilization equipment to provide individual protection for components or internal circuits. Electrical Characteristics for Series % of Ampere Rating 150% 1A – 10A 210% 0.05A – 16A 1706869 0.05A - 10A, 16A 40013834 0.05A – 6.3A *8A, *10A 40016442 *12.5A KM41462 1A – 6.3A J50248090 8A – 16A N/A 0.05A – 16A 275% 400% 1000% Ampere Rating Opening Time 0.05A – 4A 60 minutes, Minimum 5A – 6.3A 60 minutes, Minimum 8A – 16A 30 minutes, Minimum 0.05A – 4A 30 minutes, Maximum 5A – 6.3A 30 minutes, Maximum 8A – 16A 30 minutes, Maximum 0.05A – 4A 0.01 sec.., Min.; 2 sec. Max. 5A – 6.3A 0.01 sec.., Min.; 3 sec. Max. 8A – 16A 0.04 sec., Min.; 20 sec. Max. 0.05A – 4A 0.003 sec., Min.; 0.3 sec. Max. 5A – 6.3A 0.003 sec., Min.; 0.3 sec. Max. 8A – 16A 0.01 sec.., Min.; 1.0 sec. Max. 0.05A – 4A 0.02 seconds, Maximum 5A – 6.3A 0.02 seconds, Maximum 8A – 16A 0.03 seconds, Maximum Additional Information Datasheet Resources Samples Accessories For recommended fuse accessories for this product series, see ‘Recommended Accessories’ section. © 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised:GD.10/14/20 Axial Lead & Cartridge Fuses 5×20 mm > Fast-Acting > 216 Series Electrical Characteristics Specifications by Item Nominal Amp Voltage Nominal Amp Interrupting Cold Rating Rating Melting + Code Rating Resistance 2 (A) (V) I t (A2 sec) (Ohms) 0.050 0.063 0.080 0.100 0.125 0.160 0.200 0.250 0.315 0.500 0.630 0.800 001.0 1.25 01.6 002.0 02.5 3.15 004.0 005.0 06.3 008.0 010.0 12.5 0.05 0.063 0.08 0.1 0.125 0.16 0.2 0.25 0.315 0.5 0.63 0.8 1 1.25 1.6 2 2.5 3.15 4 5 6.3 8 10 12.5 250 250 250 250 250 250 250 250 250 250 250 250 250 250 250 250 250 250 250 250 250 250 250 250 016. 16 250 1500A@ 250Vac 750A@ 250Vac Agency Approvals Maximum Maximum Voltage Power Drop at Dissapation Rated at 1.5ln Current (W) (mV) PS E 15.9000 10.4500 7.8850 5.7925 3.6750 5.3490 3.3500 2.3500 1.8500 0.8660 0.4650 0.2950 0.2370 0.1530 0.1112 0.0764 0.0584 0.0368 0.0247 0.0183 0.0137 0.0123 0.0079 0.0057 0.00019 0.00079 0.00084 0.00450 0.00546 0.00326 0.00439 0.01350 0.02320 0.16500 0.05940 0.14600 0.18000 0.48000 1.00500 1.87000 3.67200 6.70000 14.99500 27.46000 56.43000 64.31500 154.34000 175.00000 10000 8800 7600 7000 5000 4300 3500 2800 2500 1800 1500 1200 1000 800 600 500 400 350 300 250 200 200 200 200 1.6 1.6 1.6 1.6 1.6 1.6 1.6 2.5 2.5 2.5 2.5 2.5 2.5 4 4 4 4 4 4 4 4 4 4 N/A** x x x x x x x x x - x x x x x x x x x x x - x x x x x x x x x x x x x x x x x x x x x x x - x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x - x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x* x* - x* x x x x x x x x x x x x x x x 0.0040 462.50000 200 N/A** - - - x*** x x x - - x*** x * - Approval for cartidge versions only. ** - Please contact Littelfuse for details on these parameters I2t test at 10x rated current *** - 1500A@250Vac for 16A + Interrupting Rating may differ based on Agency Approval. See Agency Approval certificate for more details. 0.050A 0.063A 0.080A 0.100A 0.125A 0.160A 0.200A 0.250A 0.315A 0.500A 0.630A 0.800A 1A 1.25A 1.6A 2A 2.5A 3.15A 4A 5A 6.3A 8A 10A 12.5A 16A Average Time Current Curves 10000 1000 100 TIME IN SECONDS Temperature Re-rating Curve 10 1 0.1 0.01 0.001 0.01 0.1 1 10 100 1000 CURRENT IN AMPERES © 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised:GD.10/14/20 Axial Lead & Cartridge Fuses 5×20 mm > Fast-Acting > 216 Series Soldering Parameters - Wave Soldering Recommended Process Parameters: 280 Wave Parameter Lead-Free Recommendation 260 Preheat: 240 200 Temperature Minimum: (Typical Industry Recommendation) 100°C 180 Temperature Maximum: 150°C 160 Preheat Time: 60-180 seconds (Depends on Flux Activation Temperature) 220 140 120 Solder Pot Temperature: 260°C Maximum 100 Solder Dwell Time: 2-5 seconds 80 Recommended Hand-Solder Parameters: Solder Iron Temperature: 350°C +/- 5°C Heating Time: 5 seconds max. 60 40 240 230 220 210 200 190 180 170 160 150 140 130 120 110 90 100 80 70 60 50 40 30 0 0 20 20 10 Temperature (°C) - Measured on bottom side of board 300 Note: These devices are not recommended for IR or Convection Reflow process. Time (Seconds) Cooling Time Preheat Time Dwell Time Product Characteristics –55ºC to +125ºC MIL-STD-202, Method 107, Test Condition B: (5 cycles –65°C to +125°C) MIL-STD-202, Method 201 MIL-STD-202, Method 103, Test Condition A. high RH (95%) and elevated temperature (40°C) for 240 hours. MIL-STD-202, Method 101, Test Condition B Operating Temperature Material Body: Ceramic Cap: Nickel–plated brass Leads: Tin–plated Copper Filler (160mA-16A): Sand Terminal Strength MIL-STD-202, Method 211, Test Condition A Solderability MIL-STD-202 Method 208 Humidity Product Marking Cap 1: Brand logo, current and voLage rating Cap 2: Agency approval markings Salt Spray Packaging Available in Bulk (M=1000 pcs/pkg) or on Tape/Reel (MRET1=1000 pcs/reel) Thermal Shock Dimensions Vibration Part Numbering System 0216 xxxx M X E P 20±0.5 0216 000XP 5.2 5.1±0.6 +0.1 −0.2 Series 5.1±0.6 Amp Code 0216.050XEP to 0216.800XEP 40±1.0 0216001.XEP to 0216016.XEP 40±1.0 21.5±1.0 5.6±0.4 Refer to Amp Code column of Electrical Characteristics Table Quantity Code 0.65±0.05 M = 1000 21.5±1.0 5.5±0.3 Packaging Code X = Filler Option Codes Blank : Cartidge Type Fuse E : Axial Leaded Fuse SEE NOTES All dimensions in mm Lead-free Notes: 1. 0.05A-6.3A have 0.65±0.05 diameter lead. 2. 8A-16A have 0.8±0.05 diameter lead. © 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised:GD.10/14/20 Axial Lead & Cartridge Fuses 5×20 mm > Fast-Acting > 216 Series Packaging Packaging Option Packaging Specification Quantity Quantity & Packaging Code Taping Width N/A 216 Series Bulk N/A 1000 MX Bulk N/A 1000 MXE N/A Reel and Tape EIA 296-E 1000 MRET1 T1=53mm (2.087”) Bulk N/A 1000 MXG N/A Bulk N/A 1000 MXB N/A Bulk N/A 100 HX N/A Recommended Accessories Accessory Type Holder Block Clip Series Description Max Application Voltage Max Application Amperage 345_ISF Panel Mount Shock-Safe Fuseholder 10 345 Shock-Safe Fuseholder with PC Mount, Solder Mount and Panel Mount options 20 830 PC Mount Shock-Safe Miniature Fuseholder 16 520 Metric OMNI-BLOK® Fuse Block 646 PC Mount Miniature Fuse Block 10 250 6.3 658 Surface Mount Miniature Fuse Block 10 520_W PC Mount Miniature Fuse Clip 6.3 111 PC Board Mount Fuse Clip 10 445 PC Board Mount Fuse Clip 10 Notes: 1. Do not use in applications above rating. 2. Please refer to fuseholder data sheet for specific re-rating information. 3. Please contact Littelfuse for applications greater than the max voltage and amperage shown. Disclaimer Notice - Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of and test each product selected for their own applications. Littelfuse products are not designed for, and may not be used in, all applications. Read complete Disclaimer Notice at: www.littelfuse.com/disclaimer-electronics. © 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised:GD.10/14/20