061806.3MXP

Axial Lead & Cartridge Fuses 5×20 mm > Time-Lag > 618 Series 618 Series, 5×20 mm, Time-Lag Fuse RoHS Pb Description 5×20mm Time-Lag glass body cartridge fuse designed to IEC specification. Features • Designed to International (IEC ) Standards for use globally • Meets the IEC 60127-2, Sheet 3 specification for Time-Lag fuses Agency Approvals Agency Agency File Number • Available in cartridge and axial lead form • RoHS compliant and lead-free Applications Ampere Range 2005010207170553 0.125A-6.3A Used as supplementary protection in appliance or utilization equipment to provide individual protection for components or internal circuits. E10480 0.125A-10A Additional Information 29862 0.125A-10A 40013496 N/A * Approval for Cartridge versions only 0.125A – 10A 0.125A-10A Datasheet Resources Samples Electrical Characteristics % of Ampere Rating 150% 210% 275% 400% 1000% Ampere Rating Opening Time 0.125A-6.3A 60 minutes, Minimum 8A-10A 30 minutes, Minimum 0.125A-6.3A 120 sec., Maximum 8A-10A 120 sec., Maximum 0.125A-6.3A 600 ms., Min.; 10 sec. Max. 8A-10A 600 ms., Min.; 10 sec. Max. 0.125A-6.3A 150 ms., Min.; 3 sec. Max. 8A-10A 150 ms., Min.; 3 sec. Max. 0.125A-6.3A 20 ms., Min.; 300 ms. Max. 8A-10A 20 ms., Min.; 300 ms. Max. © 2015 Littelfuse, Inc. Application testing is strongly recommended. Specifications are subject to change without notice. Revised: 06/22/15 Axial Lead & Cartridge Fuses 5×20 mm > Time-Lag > 618 Series Electrical Characteristics Agency Approvals Amp Rating (A) Voltage Rating (V) .125 0.125 250 4.2000 0.1465 1900 1.6 x x x x x .160 0.16 250 3.7000 0.14400 1500 1.6 x x x x x .200 0.2 250 1.6000 0.3410 1300 1.6 x x x x x .250 0.25 250 1.0495 0.5405 1100 1.6 x x x x x .315 0.315 250 0.8475 1.1100 1000 1.6 x x x x x .400 0.4 250 0.5350 1.3250 900 1.6 x x x x x .500 0.5 250 0.3700 2.8250 300 1.6 x x x x x .630 0.63 250 0.2750 4.6750 250 1.6 x x x x x .800 0.8 250 0.0813 3.370 150 1.6 x x x x x 001. 1 250 0.0613 6.730 150 1.6 x x x x x 1.25 1.25 250 0.0446 12.650 150 1.6 x x x x x 01.6 1.6 250 0.0336 23.350 150 1.6 x x x x x 002. 2 250 0.0293 14.450 150 1.6 x x x x x 02.5 2.5 250 0.0219 23.250 120 1.6 x x x x x 3.15 3.15 250 0.0173 38.150 100 1.6 x x x x x 004. 4 250 40 A @ 250 VAC 0.0129 69.10 100 1.6 x x x x x 005. 5 250 50 A @ 250 VAC 0.0104 111.00 100 1.6 x x x x x 06.3 6.3 250 63 A @ 250 VAC 0.0076 198.50 100 1.6 x x x x x 008. 8 250 80 A @ 250 VAC 0.0059 341.50 100 4 x x x x 010. 10 250 100 A @ 250 VAC 0.0045 568.00 100 4 x x x x Interrupting Rating 35 A @ 250 VAC Nominal Cold Resistance (Ohms) Maximum Maximum Voltage Drop at Power Rated Current Dissipation At (mV) 1.5ln(W) Amp Code Average Time Current Curves 0.125A 0.160A 0.200A 0.250A 0.315A 0.400A 0.500A 0.630A 0.800A 1A 1.25A 1.6A 2A 2.5A 3.15A 4A 5A 6.3A 8A 10A Temperature Re-rating Curve Nominal Melting I2t (A2 sec) 10000 1000 TIME IN SECONDS 100 10 1 0.1 Note: Rerating depicted in this curve is in addition to the standard derating of 25% for continuous operation. 0.01 0.01 0.1 1 10 CURRENT IN AMPERES © 2015 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 06/22/15 100 Axial Lead & Cartridge Fuses 5×20 mm > Time-Lag > 618 Series Soldering Parameters - Wave Soldering Recommended Process Parameters: 280 Wave Parameter 260 240 Lead-Free Recommendation Preheat: 220 (Depends on Flux Activation Temperature) 200 180 160 140 120 100 80 60 (Typical Industry Recommendation) Temperature Minimum: 100°C Temperature Maximum: Preheat Time: 150°C 60-180 seconds Solder Pot Temperature: 260°C Maximum Solder Dwell Time: 2-5 seconds 40 Time (Seconds) Cooling Time Preheat Time Dwell Time 240 230 220 210 200 190 180 170 160 150 140 130 120 110 90 100 80 70 60 50 40 30 0 0 20 20 10 Temperature (°C) - Measured on bottom side of board 300 Recommended Hand-Solder Parameters: Solder Iron Temperature: 350°C +/- 5°C Heating Time: 5 seconds max. Note: These devices are not recommended for IR or Convection Reflow process. Product Characteristics Material Body: Glass Cap: Nickel–plated Brass Leads: Tin–plated Copper Terminal Strength MIL-STD-202, Method 211, Test Condition A Solderability MIL-STD-202 method 208 Product Marking Cap1: Brand logo, current and voltage ratings Cap2: Agency approval marks Packaging Available in Bulk (M=1000 pcs/pkg) or on Tape/Reel (MRET1=1000 pcs/ reel) Operating Temperature –55ºC to +125ºC Thermal Shock MIL-STD-202, Method 107, Test Condition B (5 cycles, –65°C to +125°C) Vibration MIL-STD-202, Method 201 Humidity Salt Spray MIL-STD-202, Method 103, Test Condition A (High RH (95%) and elevated temperature (40°C) for 240 hours) MIL-STD-202, Method 101, Test Condition B © 2015 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 06/22/15 Axial Lead & Cartridge Fuses 5×20 mm > Time-Lag > 618 Series Dimensions Part Numbering System 0618 xxxx M X E P 20+0.5 Series 5.2+0.1 -0.2 0618 000P 5.1+0.6 Amp Code Refer to Amp Code column of Electrical Characteristics Table 5.1+0.6 Quantity Code M = 1000 0618.125 XEP to 0618010. XEP 40±1.0 5.5±0.3 21.5±1.0 Packaging Code X = Filler Option Codes 0.65±0.05* Blank : Cartidge Type Fuse E : Axial Lead Fuse All dimensions in mm Lead-free Notes: * Ratings above 6.3A have 0.8±0.05 diameter lead. Packaging Packaging Option Packaging Specification Quantity Quantity & Packaging Code Taping Width N/A N/A EIA 296-E N/A N/A N/A 1000 1000 1000 1000 1000 100 MX MXE MRET1 MXG MXB HX N/A N/A T1=53mm (2.087”) N/A N/A N/A 618 Series Bulk Bulk Reel and Tape Bulk Bulk Bulk © 2015 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 06/22/15