15KPA75A-B

TVS Diode Axial Leaded – 15000W > 15KPA series 15KPA Series RoHS Pb e3 Descriptions The 15KPA Series is designed specifically to protect sensitive electronic equipment from voltage transients induced by lightning and other transient voltage events. Uni-directional Features Bi-directional Agency Approvals Agency Agency File Number E230531 Maximum Ratings and Thermal Characteristics (TA=25OC unless otherwise noted) Parameter Symbol Value Unit Peak Pulse Power Dissipation by 10/1000μs Test Waveform (Fig.2)(Note 1) PPPM 15 kW Steady State Power Dissipation on Infinite Heat Sink at TL=75ºC PD 8.0 W Peak Forward Surge Current, 8.3ms Single Half Sine Wave Unidirectional Only (Note 2) IFSM 400 A TJ , TSTG -55 to 175 °C Typical Thermal Resistance Junction to Lead RƟJL 8.0 °C/W Typical Thermal Resistance Junction to Ambient RƟJA 40 °C/W Operating Junction and Storage Temperature Range Notes: 1. Non-repetitive current pulse , per Fig. 4 and derated above TJ (initial) =25OC per Fig. 3. 2. Measured on 8.3ms single half sine wave or equivalent square wave, duty cycle=4 per minute maximum. • Glass passivated chip junction in P600 package • 15kW peak pulse capability at 10/1000μs waveform, repetition rate (duty cycles):0.01% • Fast response time: typically less than 1.0ps from 0 Volts to BV min • Excellent clamping capability • Typical failure mode is short from over-specified voltage or current • Whisker test is conducted based on JEDEC JESD201A per its table 4a and 4c • IEC 61000-4-2 ESD 30kV(Air), 30kV (Contact) • ESD protection of data lines in accordance with IEC 61000-4-2 • EFT protection of data lines in accordance with IEC 61000-4-4 • Low incremental surge resistance • Typical IR less than 2μA when VBR min>36V • High temperature to reflow soldering guaranteed: 260°C/40sec / 0.375”, (9.5mm) lead length, 5 lbs., (2.3kg) tension • VBR @ TJ= VBR@25°C x (1+αT x (TJ - 25)) (αT:Temperature Coefficient, typical value is 0.1%) • UL Recognized compound meeting flammability rating V-0 • Matte tin lead–free plated • Halogen free and RoHS compliant • Pb-free E3 means 2nd level interconnect is Pbfree and the terminal finish material is tin(Sn) (IPC/ JEDEC J-STD-609A.01) • Recognized to UL 497B Applications TVS componants are ideal for the protection of I/O interfaces, VCC bus and other vulnerable circuits used in telecom, computer, industrial and consumer electronic applications. Additional Infomarion Functional Diagram Bi-directional Cathode Datasheet Resources Samples Anode Uni-directional © 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 08/27/20 TVS Diode Axial Leaded – 15000W > 15KPA series Electrical Characteristics (T =25°C unless otherwise noted) A Part Number (Uni) Part Number (Bi) Reverse Stand off Voltage VR (Volts) Breakdown Voltage VBR (Volts) @ IT Test Current IT MIN MAX (mA) Maximum Peak Pulse Current Ipp (A) Maximum Reverse Leakage IR @ VR (µ A) Maximum Clamping Voltage VC @ IPP (V) Agency Recognition 15KPA17A 15KPA17CA 17 18.99 20.79 50 515.4 5000 29.3 15KPA18A 15KPA18CA 18 20.11 22.01 50 488.7 5000 30.9 X X 15KPA20A 15KPA20CA 20 22.34 24.46 20 440.2 1500 34.3 X 15KPA22A 15KPA22CA 22 24.57 26.91 10 407.0 500 37.1 X 15KPA24A 15KPA24CA 24 26.81 29.35 5 371.0 150 40.7 X X 15KPA26A 15KPA26CA 26 29.04 31.80 5 343.2 50 44.0 15KPA28A 15KPA28CA 28 31.28 34.24 5 317.9 25 47.5 X 15KPA30A 15KPA30CA 30 33.51 36.70 5 297.8 15 50.7 X 15KPA33A 15KPA33CA 33 36.9 40.4 5 276.1 2 54.7 X 15KPA36A 15KPA36CA 36 40.2 44.0 5 252.5 2 59.8 X 15KPA40A 15KPA40CA 40 44.7 48.9 5 229.5 2 65.8 X 15KPA43A 15KPA43CA 43 48.0 52.6 5 216.3 2 69.8 X 15KPA45A 15KPA45CA 45 50.3 55.0 5 207.4 2 72.8 X 15KPA48A 15KPA48CA 48 53.6 58.7 5 194.3 2 77.7 X 15KPA51A 15KPA51CA 51 57.0 62.4 5 182.1 2 82.9 X 15KPA54A 15KPA54CA 54 60.3 66.0 5 172.2 2 87.7 X 15KPA58A 15KPA58CA 58 64.8 70.9 5 161.0 2 93.8 X 15KPA60A 15KPA60CA 60 67.0 73.4 5 155.0 2 97.4 X 15KPA64A 15KPA64CA 64 71.5 78.3 5 144.9 2 104.2 X 15KPA70A 15KPA70CA 70 78.2 85.6 5 132.9 2 113.6 X 15KPA75A 15KPA75CA 75 83.8 91.7 5 123.8 2 122.0 X 15KPA78A 15KPA78CA 78 87.1 95.4 5 119.7 2 126.1 X 15KPA85A 15KPA85CA 85 94.9 104.0 5 109.7 2 137.6 X 15KPA90A 15KPA90CA 90 100.5 110.1 5 103.7 2 145.6 X 15KPA100A 15KPA100CA 100 111.7 122.3 5 93.6 2 161.3 X 15KPA110A 15KPA110CA 110 122.9 134.5 5 84.5 2 178.6 X 15KPA120A 15KPA120CA 120 134.0 146.8 5 78.5 2 192.3 X 15KPA130A 15KPA130CA 130 145.2 159.0 5 72.5 2 208.3 X 15KPA150A 15KPA150CA 150 167.6 183.5 5 62.4 2 241.9 X 15KPA160A 15KPA160CA 160 178.7 195.7 5 58.4 2 258.6 X 15KPA170A 15KPA170CA 170 189.9 207.9 5 55.4 2 272.7 X X 15KPA180A 15KPA180CA 180 201.1 220.1 5 52.3 2 288.5 15KPA200A 15KPA200CA 200 223.4 244.6 5 47.3 2 319.1 X 15KPA220A 15KPA220CA 220 245.7 269.1 5 42.4 2 356.0 X X 15KPA240A 15KPA240CA 240 268.1 293.5 5 39.3 2 384.6 15KPA260A 15KPA260CA 260 290.4 318.0 5 36.2 2 416.7 X 15KPA280A 15KPA280CA 280 312.8 342.4 5 33.2 2 454.5 X For bidirectional type having VR of 30 volts and less, the IR limit is double. For parts without A, the VBR is ±10% and Vc is 5% higher than with A parts, the parts without A are currently available, but not recommended for new designs. The parts with A are preferred. © 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 08/27/20 TVS Diode Axial Leaded – 15000W > 15KPA series I-V Curve Characteristics Bi-directional Uni-directional Ipp Vc VBR VR Vc VBR VR V IR VF IT IT IR IR IT V Ipp Ipp PPPM VR VBR VC IR VF VR VBR Vc Peak Pulse Power Dissipation -- Max power dissipation Stand-off Voltage -- Maximum voltage that can be applied to the TVS without operation Breakdown Voltage -- Maximum voltage that flows though the TVS at a specified test current (IT) Clamping Voltage -- Peak voltage measured across the TVS at a specified Ippm (peak impulse current) Reverse Leakage Current -- Current measured at VR Forward Voltage Drop for Uni-directional Ratings and Characteristic Curves (T =25°C unless otherwise noted) A Figure 1 - TVS Transients Clamping Waveform Figure 2 - Peak Pulse Power Rating Curve Voltage Transients 1000 PPPM-Peak Pulse Power (kW) TJ initial = Tamb Voltage or Current Voltage Across TVS Current Through TVS 15kW at 10/1000µs, 25°C 100 10 1 Time 0.001 0.01 0.1 1 10 td-Pulse Width (ms) © 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 08/27/20 TVS Diode Axial Leaded – 15000W > 15KPA series Ratings and Characteristic Curves (T =25°C unless otherwise noted) (Continued) A Figure 4 - Test Pulse Waveform 150 100 75 50 25 0 tr=10µsec IPPM- Peak Pulse Current, % IRSM Peak Pulse Power (PPP) or Current (IPP) Derating in Percentage % Figure 3 - Peak Pulse Power Derating Curve 0 25 50 75 100 125 150 175 Half Value IPPM IPPM ( ) 2 50 200 0 10/1000µsec. Waveform as defined by R.E.A td 1.0 0 2.0 3.0 4.0 t-Time (ms) Figure 5 - Typical Junction Capacitance Figure 6 - Typical Transient Thermal Impedance 100 100000 10000 Transient Thermal Impedance (°C/W) Uni-direconal V=0V Cj (pF) Peak Value IPPM 100 TJ - Initial Junction Temperature (ºC) Bi-direconal V=0V 1000 Uni-direconal V=VR 100 Bi-direconal V=VR 10 1 0 50 100 150 200 250 300 350 10 1 0.1 0.01 0.1 1 VBR - Reverse Breakdown Voltage (V) 10 100 1000 TP - Pulse Duration (s) Figure 7 - Maximum Non-Repetitive Peak Forward Surge Current Uni-Directional Only Figure 8 - Peak Forward Voltage Drop vs Peak Forward Current (Typical Values) 1000 2 stacked-die 100 900 I F - Peak Forward Current(A) IFSM - Peak Forward Surve Current (A) TJ=25°C Pulse Width(td) is defined as the point where the peak current decays to 50% of IPPM 800 700 600 500 400 300 200 100 3 stacked-die 10 1 0.1 0 1 10 Number of Cycles at 60 Hz 100 0.0 2.0 4.0 6.0 8.0 10.0 12.0 VF - Peak Forward Voltage(V) © 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 08/27/20 TVS Diode Axial Leaded – 15000W > 15KPA series Soldering Parameters Lead–free assembly Pre Heat - Temperature Min (Ts(min)) 150°C - Temperature Max (Ts(max)) 200°C - Time (min to max) (ts) 60 – 180 secs Average ramp up rate (Liquidus Temp (TA) to peak Reflow Ramp-up 3°C/second max 3°C/second max TS(max) to TA - Ramp-up Rate tp TP - Temperature (TA) (Liquidus) 217°C - Time (min to max) (ts) 60 – 150 seconds Peak Temperature (TP) 260+0/-5 °C Time within 5°C of actual peak Temperature (tp) 20 – 40 seconds Ramp-down Rate 6°C/second max Time 25°C to peak Temperature (TP) 8 minutes Max. Do not exceed 260°C TL Temperature (T) Reflow Condition tL Ts(max) Ramp-down Ts(min) ts Preheat 25˚C t 25˚C to Peak Time (t) Flow/Wave Soldering (Solder Dipping) Peak Temperature : 265OC Dipping Time : 10 seconds Soldering : 1 time Environmental Specifications Physical Specifications Weight 0.07oz., 2.5g High Temp. Storage JESD22-A103 Case P600 molded plastic body over passivated junction. HTRB JESD22-A108 Polarity Color band denotes the cathode except Bipolar. Matte Tin axial leads, solderable per JESD22-B102. Temperature Cycling JESD22-A104 H3TRB JESD22-A101 RSH JESD22-B106 Terminal Critical Zone TL to TP Dimensions D Dimensions Cathode Band (for uni-directional products only) C A A B Inches Millimeters Min Max Min A 1.000 - 25.40 Max - B 0.340 0.360 8.60 9.10 C 0.048 0.054 1.22 1.36 D 0.340 0.360 8.60 9.10 P600 © 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 08/27/20 TVS Diode Axial Leaded – 15000W > 15KPA series Part Numbering System Part Marking System 15KPA xxx XX X Cathode Band F (for uni-directional products only) Option Code: BLANK Reel Tape -B Bulk Packaging YYWW Littelfuse Logo Type Code: A Uni-Directional (5% VBR Voltage Tolerance) CA Bi-Directional (5% VBR Voltage Tolerance) Trace Code Marking YY:Year Code WW: Week Code 15KPAXXX VR Voltage Product Type Series Code Packing Options 15KPAxxxXX Component Package P600 15KPAxxxXX-B P600 Part Number 800 Packaging Option Tape & Reel 100 Bulk Quantity Packaging Specification EIA STD RS-296 Littelfuse Spec. Tape and Reel Specification Off Center either side 0.028(0.7) 2.56 (65.0) 0.236 (6.0) 0.047 (1.2) 0.394+/-0.020 (10.0+/-0.5) 13.0 (330.2) 2.063+0.079/-0.039 (53.0+2.0/-1.0) Dimensions are in inches/mm 3.0 (76.2) 0.68 (17.27) 2.75 (69.85) Recess Depth Max. 0.75 (19.05) Direction of Feed Disclaimer Notice - Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of and test each product selected for their own applications. Littelfuse products are not designed for, and may not be used in, all applications. Read complete Disclaimer Notice at www.littelfuse.com/disclaimer-electronics. © 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 08/27/20