2016L260/24MR

PolySwitch® Resettable PPTC Datasheet 2016L Series Surface Mount RoHS Description The 2016L Series PTC provides surface mount overcurrent protection for low voltage (≤60V) applications where resettable protection is desired. Features ■ RoHS compliant, lead-free and halogen-free ■ High voltage ■ Low-profile ■ Fast response to fault currents Applications ■ Low voltage telecom equipment protection ■ IEEE 1394 port protection ■ Powered ethernet port protection (IEEE 802.3 af) Additional Information ■ Automotive electronic control module protection Agency Approvals Agency Resources Accessories Agency File Number E183209 Samples R50119118 Electrical Characteristics I trip (A) V max (Vdc) I max (A) P d typ. (W) Maximum Time To Trip Resistance Agency Approvals Part Number Marking I hold (A) 2016L030 LF030 0.30 0.60 60 20 1.40 1.5 2016L050 LF050 0.55 1.10 60 20 1.40 2.5 2016L075/60 LF075 0.75 1.50 60 20 1.40 8.0 0.5 0.130 0.900 X X 2016L100 LF100 1.10 2.20 15 40 1.40 8.0 0.5 0.100 0.400 X X 2016L100/33 LF100-33 1.10 2.20 33 40 1.40 8.0 0.5 0.100 0.400 X X 2016L150 LF150 1.50 3.00 15 40 1.40 8.0 1.0 0.070 0.180 X X 2016L150/33 LF150-33 1.50 3.00 33 40 2.0 8.00 1.00 0.070 0.180 X X 2016L200 LF200 2.00 4.20 6 40 1.40 8.0 3.0 0.048 0.100 X X 2016L260/24 LF260-24 2.60 5.00 24 40 1.6 8.00 5.00 0.025 0.075 X X 2016L300/16 LF300 3.00 5.00 16 40 1.6 8.00 10.00 0.015 0.048 X X 2016L500 LF500 5.00 10.00 6 100 2.0 25.00 2.00 0.005 0.025 X X Current (A) R min (Ω) R 1max (Ω) 3.0 0.500 2.300 X X 5.0 0.200 1.000 X X Time (Sec.) I hold = Hold current: maximum current device will pass without tripping in 20°C still air. R typ = Typical resistance of device in initial (un-soldered) state. I trip = Trip current: minimum current at which the device will trip in 20°C still air. R 1max = Maximum resistance of device at 20°C measured one hour after tripping or reflow soldering of 260°C for 20 sec. V max = Maximum voltage device can withstand without damage at rated current (I max) Caution: Operation beyond the specified rating may result in damage and possible arcing and flame. I max = Maximum fault current device can withstand without damage at rated voltage (Vmax) * Agency Approval is Pending P d = Power dissipated from device when in the tripped state at 20°C still air. R min = Minimum resistance of device in initial (un-soldered) state. ■ Exposure to silicon-based oils, solvents, electrolytes, acids, and similar materials can adversely affect the performance of these PPTC devices Warning ■ Users shall independently assess the suitability of these devices for each of their applications ■ These devices undergo thermal expansion under fault conditions, and thus shall be provided with adequate space and be protected against mechanical stresses ■ Operation of these devices beyond the stated maximum ratings could result in damage to the devices and lead to electrical arcing and/or fire ■ Circuits with inductance may generate a voltage (L di/dt) above the rated voltage of the PPTC device. ■ These devices are intended to protect against the effects of temporary over-current or over-temperature conditions and are not intended to perform as protective devices where such conditions are expected to be repetitive or prolonged in duration 1 © 2021 Littelfuse, Inc. Specifications are subject to change without notice. Revised: GD. 10/29/21 PolySwitch® Resettable PPTC Datasheet 2016L Series Surface Mount Temperature Rerating Ambient Operation Temperature -40°C -20°C 0°C 20°C 2016L030 0.45 0.40 0.35 0.30 0.25 0.23 0.20 0.18 0.14 2016L050 0.93 0.95 0.65 0.55 0.42 0.38 0.33 0.30 0.23 2016L075/60 1.05 1.06 0.85 0.75 0.60 0.55 0.45 0.40 0.30 Part Number 40°C 50°C 60°C 70°C 85°C Hold Current (A) 2016L100 1.66 1.47 1.29 1.10 0.91 0.83 0.73 0.64 0.50 2016L100/33 1.66 1.47 1.29 1.10 0.91 0.83 0.73 0.64 0.50 2016L150 2.26 2.00 1.76 1.50 1.24 1.13 1.00 0.87 0.68 2016L150/33 2.26 2.00 1.76 1.50 1.24 1.13 1.00 0.87 0.68 2016L200 2.80 2.50 2.19 2.00 1.84 1.74 1.50 1.34 1.14 2016L260/24 3.82 3.46 3.06 2.60 2.24 2.03 1.82 1.60 1.26 2016L300/16 4.40 3.96 3.52 3.00 2.65 2.43 2.20 1.96 1.59 2016L500 7.29 6.57 5.86 5.00 4.38 4.02 3.66 3.26 2.66 Temperature Rerating Curve Average Time Current Curves 1.50A/33 2.60A/24 3.00A/16 5.00A 150% Percentage of Rated Current 0.30A 0.50A 0.75A/60 1.00A 1.00A/33 1.50A 2.00A 170% Time in Seconds 100 10 130% 110% 90% 70% 50% 30% 10% -40 1 -30 -20 -10 0 10 20 30 40 Temperature (°C) 50 60 70 80 85 Note: Typical Temperature rerating curve, refer to table for derating data 0.1 0.01 0.1 1 10 Current in Amperes The average time current curves and Temperature Rerating curve performance is affected by a number or variables, and these curves provided as guidance only. Customer must verify the performance in their application. 2 © 2021 Littelfuse, Inc. Specifications are subject to change without notice. Revised: GD. 10/29/21 PolySwitch® Resettable PPTC Datasheet 2016L Series Surface Mount Soldering Parameters Pb-Free Assembly Average Ramp-Up Rate (TS(max) to TP) 3°C/second max Pre Heat: Temperature Min (Ts(min)) 150°C Temperature Max (Ts(max)) 200°C Time (Min to Max) (ts) 60 – 180 secs Temperature (TL) Time Maintained Above: Temperature (t ) L 217°C Peak / Classification Temperature (TP) 260 Time within 5°C of actual peak Temperature (tp) 20 – 40 seconds Ramp-down Rate 6°C/second max Time 25°C to peak Temperature (TP) 8 minutes Max. °C Critical Zone tL to tP Ramp-up TL TS(max) 60 – 150 seconds +0/-5 tP TP Temperature Profile Feature tL Ramp-do Ramp-down Preheat TS(min) 25 tS time to peak temperature Time -- All temperature refer to topside of the package, measured on the package body surface -- If reflow temperature exceeds the recommended profile, devices may not meet the performance requirements -- Recommended reflow methods: IR, vapor phase oven, hot air oven, N2 environment for lead -- Recommended maximum paste thickness is 0.25mm(0.010inch) -- Devices can be cleaned usingstandard industry methods and solvents -- Devices can be reworked using the standard industry practices Physical Specifications Environmental Specifications Terminal Material Solder-Plated Copper (Solder Material: Matte Tin(Sn)) Operating Temperature -40°C to +85°C Lead Solderability Meets EIA Specification RS186-9E, ANSI/ J-STD-002 Category 3. Maximum Device Surface Temperature in Tripped State 125°C Passive Aging +85°C, 1000 hours -/+5% typical resistance change Humidity Aging +85°C, 85%,R.H.,1000 hours -/+5% typical resistance change Thermal Shock MIL–STD–202, Method 107 +85°C/-40°C 20 times -30% typical resistance change Solvent Resistance MIL–STD–202, Method 215 No change Vibration MIL–STD–883, Method 2007, Condition A No change Moisture Sensitivity Level Level 1, J–STD–020 3 © 2021 Littelfuse, Inc. Specifications are subject to change without notice. Revised: GD. 10/29/21 PolySwitch® Resettable PPTC Datasheet 2016L Series Surface Mount Dimensions (mm) C A Top View 100 Bottom View 100 100 -33 B D E A Part Number Inches Min Max 3.40 mm (.133”) Pad Layout 4.60 mm (.181”) 1.50 mm (.059”) B mm Min Max Inches Min 2016L030 2016L050 2016L075/60 2016L100 2016L100/33 0.19 0.21 4.72 5.44 0.15 2016L150 2016L150/33 2016L200 2016L260/24 2016L300/16 2016L500 Max 0.17 MARKING CODE VARIES WITH AMPERAGE AND VOLTAGE RATING SEE ELECTRICAL CHARACTERISTICS CHART SHOWN ARE: - 1.1A/15V RATING (LEFT) - 1.1A/33V RATING (RIGHT) Side View C mm Min 3.7 Max D Inches mm Inches Min Max Min Max Min 0.03 0.05 0.05 4.43 0.02 0.03 0.03 4.43 0.03 4.43 0.02 0.05 0.08 0.08 0.03 0.05 0.06 0.06 0.03 0.75 1.20 1.20 0.50 0.75 0.75 0.80 0.50 1.25 2.00 2.00 0.75 1.25 1.55 0.01 1.60 0.75 4.43 0.03 0.06 0.80 1.60 E mm Max Min Max 0.06 0.3 1.5 Inches Min Max mm Min Max 0.01 0.03 0.25 0.65 Part Ordering Number System 2016 L xxx /xx D R - A SERIES -A: Automotive grade Blank: Standard version PACKAGING STYLE R: Tape & Reel QUANTITY CODE: D=1500 M=1000 P=2000 SPECIAL VOLTAGE RATING ITEM (Not applicable to all parts. Refer to Electrical Characteristics Table for additional information) I HOLD HOLD CURRENT CODE (Refer to Electrical Characteristics Table) L: LITTELFUSE SURFACE MOUNT PPTC DEVICE SIZE CODE (0.20 x 0.16 inch) Packaging Part Number Ordering Number Halogen Free I hold (A) I hold Code 2016L030 2016L050 2016L075/060 2016L100 2016L100/33 2016L150 2016L150/33 2016L200 2016L260/24 2016L300/16 2016L500 2016L030DR 2016L050MR 2016L075/60MR 2016L100PR 2016L100/33DR 2016L150DR 2016L150/33DR 2016L200PR 2016L260/24MR 2016L300/16MR 2016L500DR Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes 0.30 0.55 0.75 1.10 1.10 1.50 1.50 2.00 2.60 3.00 5.00 030 050 075 110 110 150 150 200 260 300 500 Voltage Option /60 /33 /33 /24 /16 /6 4 Packaging Option Quantity Tape and Reel Tape and Reel Tape and Reel Tape and Reel Tape and Reel Tape and Reel Tape and Reel Tape and Reel Tape and Reel Tape and Reel Tape and Reel 1500 1000 1000 2000 1500 1500 1,500 2000 1,000 1,000 1,500 Quantity & Packaging Codes DR MR MR PR DR DR DR PR MR MR DR © 2021 Littelfuse, Inc. Specifications are subject to change without notice. Revised: GD. 10/29/21 PolySwitch® Resettable PPTC Datasheet 2016L Series Surface Mount Tape and Reel Specifications TAPE SPECIFICATIONS: EIA-481-1 (mm) 2016L100 2016L200 2016L030 2016L100/33 2016L150 2016L150/33 2016L500 2016L050 2016L075/60 2016L260/24 2016L300/16 W 12.0+/- 0.30 12.0+/- 0.30 12.0+/- 0.30 C Ø178.0+/-1.0 REEL DIMENSIONS: EIA-481-1 (mm) F 5.50+/- 0.05 5.50+/- 0.05 5.50+/- 0.05 D Ø60.2+/-0.5 E1 1.75+/- 0.10 1.75+/- 0.10 1.75+/- 0.10 H 16.0+/- 0.5 D0 1.55+/- 0.05 1.55+/- 0.05 1.55+/- 0.05 W 13.2+/- 1.5 D1 1.50 (MIN) 1.50+/-0.10 1.50+/-0.10 P0 4.0+/- 0.10 4.0+/- 0.10 4.0+/- 0.10 P1 8.0+/- 0.10 8.0+/- 0.10 8.0+/- 0.10 P2 2.0+/- 0.05 2.0+/- 0.05 2.0+/- 0.05 A0 4.40+/- 0.10 4.48+/- 0.10 4.45+/- 0.10 B0 5.50+/- 0.10 5.40+/- 0.10 5.48+/- 0.10 T 0.25+/- 0.10 0.25+/- 0.10 0.25+/- 0.10 KO 0.75+/-0.10 1.36+/- 0.10 1.86+/- 0.10 Leader Min. 390 390 390 Trailer Min. 160 160 160 Tape and Reel Diagram D0 P0 P1 E1 P2 H F W D T A0 C D1 K0 B0 W Disclaimer Notice - Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of and test each product selected for their own applications. Littelfuse products are not designed for, and may not be used in, all applications. Read complete Disclaimer Notice at www.littelfuse.com/disclaimer-electronics. 5 © 2021 Littelfuse, Inc. Specifications are subject to change without notice. Revised: GD. 10/29/21