2N6565RP

Teccor® brand Thyristors 0.8 Amp Sensitive SCRs EC103xx & SxSx Series Description Excellent unidirectional switches for phase control applications such as heating and motor speed controls. Sensitive gate SCRs are easily triggered with microAmps of current as furnished by sense coils, proximity switches, and microprocessors. Features & Benefits t

3P)4
DPNQMJBOU t

(MBTT
o
QBTTJWBUFE
junctions Main Features t

7PMUBHF
DBQBCJMJUZ
VQ
to 600 V t

4VSHF
DBQBCJMJUZ
VQ
UP
20 A Applications Symbol IT(RMS) VDRM /VRRM IGT Value Unit 0.8 A 400 to 600 V 12 to 500 μA Typical applications are capacitive discharge systems for strobe lights and gas engine ignition. Also controls for power tools, home/brown goods and white goods appliances. Schematic Symbol A K G Absolute Maximum Ratings — Sensitive SCRs Parameter Test Conditions Value Unit IT(RMS) Symbol RMS on-state current TC = 75°C 0.8 A IT(AV) Average on-state current TC = 75°C 0.51 A single half cycle; f = 50Hz; TJ (initial) = 25°C 16 single half cycle; f = 60Hz; TJ (initial) = 25°C 20 I2t Value for fusing tp = 8.3 ms 1.6 A2s Critical rate of rise of on-state current f = 60 Hz ; TJ = 110°C 50 A/μs Peak gate current TJ = 110°C 1 A Average gate power dissipation TJ = 110°C 0.1 W Storage temperature range -40 to 150 °C Operating junction temperature range -40 to 110 °C ITSM I 2t di/dt IGM PG(AV) Tstg TJ EC103xx & SxSx Series Peak non-repetitive surge current 189 A ©2013 Littelfuse, Inc Specifications are subject to change without notice. Revised: 09/23/13 Teccor® brand Thyristors 0.8 Amp Sensitive SCRs Electrical Characteristics (TJ = 25°C, unless otherwise specified) Value Symbol IGT VGT Test Conditions MAX. VD = 6V; RL = 100  dv/dt VD = VDRM; RGK = 1kΩ SxS1 EC103X1 SxS2 EC103X2 12 50 MAX. 400V 600V VGD VD = VDRM; RL = 3.3 k; TJ = 110°C MIN. IT = 20mA (initial), RGK = 1k MAX. tq (1) MAX. tgt IG = 2 x IGT; PW = 15μs; IT = 1.6A SxS3 EC103X3 Unit 200 500 μA 0.8 MIN. IH SxS / 2N6565 EC103X V 20 25 30 40 10 10 15 20 0.2 0.25 V 5 60 TYP. V/μs 2 5 8 mA 50 45 μs 20 30 μs (1) IT=1A; tp=50μs; dv/dt=5V/μs; di/dt=-5A/μs Static Characteristics Symbol Test Conditions IT = 1.2A; tp = 380 μs VTM Value Unit 1.7 V MAX. TJ = 25°C IDRM / IRRM VDRM = VRRM RGK = 1k 1 TJ = 100°C 50 MAX. TJ = 110°C μA 100 Thermal Resistances Symbol Parameter R(J-C) Junction to case (AC) R(J-A) Junction to ambient Value EC103xy/2N6565 75 SxSy 60* EC103xy/2N6565 160 Unit °C/W °C/W Notes: x = voltage, y = sensitivity * = Mounted on 1 cm2 copper (two-ounce) foil surface EC103xx & SxSx Series 190 ©2013 Littelfuse, Inc Specifications are subject to change without notice. Revised: 09/23/13 Teccor® brand Thyristors 0.8 Amp Sensitive SCRs Figure 1: Normalized DC Gate Trigger Current vs. Junction Temperature Figure 2: Normalized DC Gate Trigger Voltage vs. Junction Temperature 2.0 Ratio of VGT / VGT (TJ = 25ºC) Ratio of IGT/IGT (TJ = 25°C) 4.0 3.0 2.0 1.0 1.5 1.0 0.5 0.0 0.0 -40 -15 10 35 60 85 -40 110 -15 10 Junction Temperature (TJ) -- (°C) Figure 3: Normalized DC Holding Current vs. Junction Temperature 85 110 10 Instantaneous On-state Current (iT) – Amps 2.5 Ratio of IH / IH (TJ = 25°C) 60 Figure 4: On-State Current vs. On-State Voltage (Typical) 3.0 2.0 1.5 1.0 0.5 0.0 TJ = 25°C 8 6 4 2 0 -40 -15 10 35 60 85 0.7 110 0.8 Junction Temperature (TJ) -- (°C) 0.9 1.0 1.1 1.2 1.3 1.4 1.5 1.6 Instantaneous On-state Voltage (vT) – Volts Figure 5: Power Dissipation (Typical) vs. RMS On-State Current Figure 6: Maximum Allowable Case Temperature vs. RMS On-State Current 0.7 115 Maximum Allowable Case Temperature (TC) - °C Average On-State Power Dissipation [PD(AV)] - (Watts) 35 Junction Temperature (TJ) -- (°C) 0.6 105 0.5 95 0.4 0.3 85 0.2 75 0.1 CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 180° 65 0.0 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.0 0.8 EC103xx & SxSx Series 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 RMS On-State Current [IT(RMS)] - Amps RMS On-State Current [IT(RMS)] - Amps 191 ©2013 Littelfuse, Inc Specifications are subject to change without notice. Revised: 09/23/13 Teccor® brand Thyristors 0.8 Amp Sensitive SCRs Figure 7: Maximum Allowable Case Temperature vs. Average On-State Current Figure 8: Maximum Allowable Ambient Temperature vs. RMS On-State Current 120 Maximum Allowable Ambient Temperature (TA) - °C Maximum Allowable Case Temperature (TC) - °C 115 CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 180° FREE AIR RATING 100 105 80 95 60 85 40 75 20 CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 180° 65 0.0 0.1 0.2 0.3 0.4 0.5 0 0.0 0.6 0.1 0.2 Average On-State Current [IT(AVE)] - Amps Figure 9: Maximum Allowable Ambient Temperature vs. Average On-State Current 0.4 0.5 0.6 0.7 0.8 0.9 1.0 Figure 10: Peak Capacitor Discharge Current 120 180 CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 180° FREE AIR RATING 100 Peak Discharge Current (ITM) -Amps Maximum Allowable Ambient Temperature (TA) - °C 0.3 RMS On-State Current [IT(RMS)] - Amps 80 60 40 20 160 140 1 Hz 120 12 Hz 100 60 Hz 80 60 ITRM 40 20 tW 0 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0 0.7 1 10 100 Pulse Current Duration (tW) - μs Average On-State Current [IT(AVE)] - Amps Figure 11: Peak Repetitive Sinusoidal Pulse Current Peak Discharge Current (ITM) - Amps 180 160 140 120 1 Hz 100 80 12 Hz 60 ITM 40 60 Hz 20 tW 0 1 10 100 Pulse Current Duration (tW) - μs EC103xx & SxSx Series 192 ©2013 Littelfuse, Inc Specifications are subject to change without notice. Revised: 09/23/13 Teccor® brand Thyristors 0.8 Amp Sensitive SCRs Figure 12: Surge Peak On-State Current vs. Number of Cycles Peak Surge (Non-repetitive) On-state Current (ITSM) – Amps 100.0 SUPPLY FREQUENCY: 60 Hz Sinusoidal LOAD: Resistive RMS On-State Current: [IT(RMS)]: Maximum Rated Value at Specified Case Temperature Notes: 1. Gate control may be lost during and immediately following surge current interval. 2. Overload may not be repeated until junction temperature has returned to steady-state rated value. 10.0 1.0 0.1 1 10 100 1000 Surge Current Duration -- Full Cycles Figure 13: Simple Test Circuit for Gate Trigger Voltage and Current Note: V1 — 0 V to 10 V dc meter VGT — 0 V to 1 V dc meter IG — 0 mA to 1 mA dc milliammeter R1 — 1 k potentiometer Reset Normally-closed Pushbutton To measure gate trigger voltage and current, raise gate voltage (VGT) until meter reading V1 drops from 6 V to 1 V. Gate trigger voltage is the reading on VGT just prior to V1 dropping. Gate trigger current IGT Can be computed from the relationship 100 + D.U.T. 6VDC IGT – V1 IN4001 IG 1k (1%) 100 R1 VGT IGT = IG- ____ Amps 1000 VGT where IG is reading (in amperes) on meter just prior to V1 dropping Note: IGT may turn out to be a negative quantity (trigger current flows out from gate lead). If negative current occurs, IGT value is not a valid reading. Remove 1 k resistor and use IG as the more correct IGT value. This will occur on 12 μA gate products. EC103xx & SxSx Series 193 ©2013 Littelfuse, Inc Specifications are subject to change without notice. Revised: 09/23/13 Teccor® brand Thyristors 0.8 Amp Sensitive SCRs Soldering Parameters Reflow Condition 1C
o
'SFF
BTTFNCMZ Pre Heat 150°C - Temperature Max (Ts(max)) 200°C - Time (min to max) (ts) 
o

TFDT Average ramp up rate (Liquidus Temp) (TL) to peak 5°C/second max TS(max) to TL - Ramp-up Rate 5°C/second max Reflow - Temperature (TL) (Liquidus) 217°C - Temperature (tL) 
o

TFDPOET Peak Temperature (TP) 260+0/-5 °C Time within 5°C of actual peak Temperature (tp) 
o

TFDPOET Ramp-down Rate 5°C/second max Time 25°C to peak Temperature (TP) 8 minutes Max. Do not exceed 280°C Temperature - Temperature Min (Ts(min)) Body Material Lead Material Ramp-up TL tL TS(max) Preheat TS(min) 25 time to peak temperature Time Environmental Specifications Test 100% Matte Tin-plated/Pb-free Solder Dipped AC Blocking UL recognized epoxy meeting flammability classification 94V-0 Temperature Cycling Copper Alloy Temperature/ Humidity Design Considerations High Temp Storage Careful selection of the correct device for the application’s operating parameters and environment will go a long way toward extending the operating life of the Thyristor. Good design practice should limit the maximum continuous current through the main terminals to 75% of the device rating. Other ways to ensure long life for a power discrete semiconductor are proper heat sinking and selection of voltage ratings for worst case conditions. Overheating, overvoltage (including dv/dt), and surge currents are the main killers of semiconductors. Correct mounting, soldering, and forming of the leads also help protect against component damage. Low-Temp Storage EC103xx & SxSx Series Ramp-do Ramp-down tS Physical Specifications Terminal Finish tP TP Thermal Shock Autoclave 194 Specifications and Conditions MIL-STD-750, M-1040, Cond A Applied Peak AC voltage @ 110°C for 1008 hours MIL-STD-750, M-1051, 100 cycles; -40°C to +150°C; 15-min dwell-time EIA / JEDEC, JESD22-A101 1008 hours; 320V - DC: 85°C; 85% rel humidity MIL-STD-750, M-1031, 1008 hours; 150°C 1008 hours; -40°C MIL-STD-750, M-1056 10 cycles; 0°C to 100°C; 5-min dwelltime at each temperature; 10 sec (max) transfer time between temperature EIA / JEDEC, JESD22-A102 168 hours (121°C at 2 ATMs) and 100% R/H Resistance to Solder Heat MIL-STD-750 Method 2031 Solderability ANSI/J-STD-002, category 3, Test A Lead Bend MIL-STD-750, M-2036 Cond E ©2013 Littelfuse, Inc Specifications are subject to change without notice. Revised: 09/23/13 Teccor® brand Thyristors 0.8 Amp Sensitive SCRs Dimensions – TO-92 (E Package) TC Measuring Point Inches Dimension A B Cathode Anode Gate E Min Max Min Max A 0.176 0.196 4.47 4.98 B 0.500 - 12.70 - D 0.095 0.105 2.41 2.67 E 0.150 - 3.81 - F 0.046 0.054 1.16 1.37 G 0.135 0.145 3.43 3.68 H 0.088 0.096 2.23 2.44 J 0.176 0.186 4.47 4.73 K 0.088 0.096 2.23 2.44 L 0.013 0.019 0.33 0.48 M 0.013 0.017 0.33 0.43 All leads insulated from case. Case is electrically nonconductive. G H M Millimeters F L D K J Dimensions — Compak (C Package) TC / TL Temperature Measurement Point Dimension B D M N P A C Cathode Anode H F L E J 0.079 (2.0) K 0.079 (2.0) G 0.079 (2.0) 0.040 (1.0) 0.030 (0.76) 0.110 (2.8) Dimensions are in inches (and millimeters). Pad Outline EC103xx & SxSx Series 195 Inches Millimeters Min Max Min Max A 0.130 0.156 3.30 3.95 B 0.201 0.220 5.10 5.60 Gate C 0.077 0.087 1.95 2.20 D 0.159 0.181 4.05 4.60 E 0.030 0.063 0.75 1.60 F 0.075 0.096 1.90 2.45 G 0.002 0.008 0.05 0.20 H 0.077 0.104 1.95 2.65 J 0.043 0.053 1.09 1.35 K 0.006 0.016 0.15 0.41 L 0.030 0.055 0.76 1.40 M 0.022 0.028 0.56 0.71 N 0.027 0.033 0.69 0.84 P 0.052 0.058 1.32 1.47 ©2013 Littelfuse, Inc Specifications are subject to change without notice. Revised: 09/23/13 Teccor® brand Thyristors 0.8 Amp Sensitive SCRs Product Selector Voltage Part Number 400V 600V X X EC103 x 1 EC103 x 2 800V 1000V Gate Sensitivity Type Package 12μA Sensitive SCR TO-92 X X 50μA Sensitive SCR TO-92 X / 2N6565 X 200μA Sensitive SCR TO-92 EC103 x 3 X X 500μA Sensitive SCR TO-92 S x S1 X X 12μA Sensitive SCR Compak S x S2 X X 50μA Sensitive SCR Compak SxS X X 200μA Sensitive SCR Compak S x S3 X X 500μA Sensitive SCR Compak EC103 x Note: x = Voltage Packing Options Part Number Marking Weight EC103xy / 2N6565 Packing Mode Base Quantity EC103xy / 2N6565 0.19 g Bulk 2000 EC103xyRP EC103xy 0.19 g Reel Pack 2000 EC103xyAP EC103xy 0.19 g Ammo Pack 2000 SxSy 0.08 g Embossed Carrier 2500 SxSyRP Note: x = Voltage, y = sensitivity TO-92 (3-lead) Reel Pack (RP) Radial Leaded Specifications Meets all EIA-468-C Standards 1.6 (41.0) 0.236 (6.0) 0.708 (18.0) 0.02 (0.5) 0.098 (2.5) MAX 1.26 (32.0) 0.354 (9.0) 0.5 (12.7) Cathode 0.1 (2.54) 0.2 (5.08) Anode Gate 0.157 DIA (4.0) 14.17(360.0) Flat up 1.97 (50.0) Direction of Feed EC103xx & SxSx Series 196 Dimensions are in inches (and millimeters). ©2013 Littelfuse, Inc Specifications are subject to change without notice. Revised: 09/23/13 Teccor® brand Thyristors 0.8 Amp Sensitive SCRs TO-92 (3-lead) Ammo Pack (AP) Radial Leaded Specifications Meets all EIA-468-C Standards 0.236 (6.0) 1.62 (41.2) 0.708 (18.0) 0.02 (0.5) 0.098 (2.5) MAX 1.27 (32.2) 0.354 (9.0) 0.157 (4.0) DIA Anode Cathode 0.2 (5.08) Gate 0.1 (2.54) 0.5 (12.7) Flat down n of Directio Feed 25 Devices per fold 1.85 (47.0) 12.2 (310.0) 1.85 (47.0) Dimensions are in inches (and millimeters). 13.3 (338.0) Compak Embossed Carrier Reel Pack (RP) Specifications Meets all EIA-481-1 Standards 0.157 (4.0) 0.47 (12.0) Anode 0.36 (9.2) 8.0 0.315 (8.0) 0.512 (13.0) Arbor Hole Dia. Gate Cathode 0.059 DIA (1.5) Cover tape 12.99 (330.0) Dimensions are in inches (and millimeters). 0.49 (12.4) Direction of Feed EC103xx & SxSx Series 197 ©2013 Littelfuse, Inc Specifications are subject to change without notice. Revised: 09/23/13 Teccor® brand Thyristors 0.8 Amp Sensitive SCRs Part Numbering System (TO-92) Part Marking System EC 103 D 1 75 TO-92 (E Package) EC103D1 DEVICE TYPE EC: TO-92 SCR 2N: JEDEC Lead Form Dimension xx: Lead Form Option YMLXX ® CURRENT RATING 103: 0.8A (TO-92) Date Code Marking SENSITIVITY & TYPE 1: 12 μ A 2: 50 μ A [blank]: 200 μ A 3: 500 μ A VOLTAGE RATING D: 400V M: 600V (JEDEC) 6565: 400V Y:Year Code M: Month Code L: Location Code XX: Lot Serial Code Part Numbering System (Compak) S 6 DEVICE TYPE S: Compak SCR VOLTAGE RATING 4: 400V 6: 600V Part Marking System (Compak) S 1 Compak (C Package) SENSITIVITY & TYPE 1: 12 μ A 2: 50 μ A [blank]: 200 μ A 3: 500 μ A S6S1 ® Date Code Marking Y:Year Code M: Month Code XXX: Lot Trace Code CURRENT RATING S: 0.8A (Compak) EC103xx & SxSx Series YMXXX 198 ©2013 Littelfuse, Inc Specifications are subject to change without notice. Revised: 09/23/13 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Littelfuse: 2N6565RP