30R160UPR

Resettable PPTC Datasheet 30R Series Radial Leaded RoHS Description The 30R Series radial leaded device is designed to provide overcurrent protection for low voltage (≤30V) applications where space is not a concern and resettable protection is preferred. Features ■ Cured, flame retardant epoxy polymer insulating material meets UL 94V-0 requirements ■ Fast time–to-trip ■ RoHS compliant, Lead-Free and Halogen-Free* Applications ■ General electronics ■ USB hubs, ports and peripherals Additional Information ■ Computers & peripherals ■ Automotive applications ■ Motor protection Agency Approvals Resources Accessories Agency Samples Agency File Number E183209 R50119318 Electrical Characteristics Pd Part Number I hold (A) I trip (A) V max (Vdc) I max (A) typ. (W) 30R090U 30R110U 30R135U 30R160U 30R185U 30R250U 30R300U 30R400U 30R500U 30R600U 30R700U 30R800U 30R900U 0.90 1.10 1.35 1.60 1.85 2.50 3.00 4.00 5.00 6.00 7.00 8.00 9.00 1.80 2.20 2.70 3.20 3.70 5.00 6.00 8.00 10.00 12.00 14.00 16.00 18.00 30 30 30 30 30 30 30 30 30 30 30 30 30 40 40 40 40 40 40 40 40 40 40 40 40 40 0.6 0.7 0.8 0.9 1.0 1.2 2.0 2.5 3.0 3.5 3.8 4.0 4.2 Caution: Operation beyond the specified rating may result in damage and possible arcing and flame. I hold = Hold current: maximum current device will pass without tripping in 20°C still air. I trip = Trip current: minimum current at which the device will trip in 20°C still air. Vint = Maximum voltage the device can withstand without damage at rated current (I max) Vop = The device regular operation voltage I max = Maximum fault current device can withstand without damage at rated voltage (Vmax) P d = Power dissipated from device when in the tripped state at 20°C still air. Maximum Time To Trip Current Time (A) (Sec.) 4.50 5.50 6.75 8.00 9.25 12.50 15.00 20.00 25.00 30.00 35.00 40.00 40.00 5.90 6.60 7.30 8.00 8.70 10.30 10.80 12.70 14.50 16.00 17.50 18.80 20.00 Resistance R min R 1max (Ω) (Ω) 0.070 0.050 0.040 0.030 0.030 0.020 0.020 0.010 0.010 0.005 0.005 0.005 0.005 Agency Approvals 0.220 0.170 0.130 0.110 0.090 0.070 0.080 0.050 0.050 0.040 0.030 0.020 0.020 X X X X X X X X X X X X X X X X X X X X X X X X X X R min = Minimum resistance of device in initial (un-soldered) state. R typ = Typical resistance of device in initial (un-soldered) state. R 1max = Maximum resistance of device at 20°C measured one hour after tripping. * Effective February 11, 2010 onward, all 600R PTC products will be manufactured Halogen Free (HF). Existing Non-Halogen Free 600R PTC products may continue to be sold, until supplies are depleted. This change will have no effect on 600R product specifications or performance. Warning • Users shall independently assess the suitability of these devices for each of their applications • Operation of these devices beyond the stated maximum ratings could result in damage to the devices and lead to electrical arcing and/or fire • These devices are intended to protect against the effects of temporary over-current or over-temperature conditions and are not intended to perform as protective devices where such conditions are expected to be repetitive or prolonged in duration • Exposure to silicon-based oils, solvents, electrolytes, acids, and similar materials can adversely affect the performance of these PPTC devices • These devices undergo thermal expansion under fault conditions, and thus shall be provided with adequate space and be protected against mechanical stresses • Circuits with inductance may generate a voltage (L di/dt) above the rated voltage of the PPTC device. 1 © 2021 Littelfuse, Inc. Specifications are subject to change without notice. Revised: GD. 05/07/21 Resettable PPTC Datasheet 30R Series Radial Leaded Temperature Rerating Ambient Operation Temperature -40°C -20°C 0°C 20°C 1.31 1.60 1.96 2.32 2.68 3.63 4.35 5.80 7.25 8.70 10.15 11.60 13.05 1.17 1.43 1.76 2.08 2.41 3.25 3.90 5.20 6.50 7.80 9.10 10.40 11.70 1.04 1.27 1.55 1.84 2.13 2.88 3.45 4.60 5.75 6.90 8.05 9.20 10.35 0.90 1.10 1.35 1.60 1.85 2.50 3.00 4.00 5.00 6.00 7.00 8.00 9.00 40°C Part Number 30R090U 30R110U 30R135U 30R160U 30R185U 30R250U 30R300U 30R400U 30R500U 30R600U 30R700U 30R800U 30R900U 50°C 60°C 70°C 85°C 0.69 0.85 1.04 1.23 1.42 1.93 2.31 3.08 3.85 4.62 5.39 6.16 6.93 0.61 0.75 0.92 1.09 1.26 1.70 2.04 2.72 3.40 4.08 4.76 5.44 6.12 0.55 0.67 0.82 0.98 1.13 1.53 1.83 2.44 3.05 3.66 4.27 4.88 5.49 0.47 0.57 0.70 0.83 0.96 1.30 1.56 2.08 2.60 3.12 3.64 4.16 4.68 Hold Current (A) 0.75 0.91 1.12 1.33 1.54 2.08 2.49 3.32 4.15 4.98 5.81 6.64 7.47 Temperature Rerating Curve Average Time Current Curves 100000 170% 150% Percentage of Rated Current 10000 Time in Seconds 1000 C H KL M A B DE F G I J 100 130% 110% 90% 70% 50% 30% 10% 10 -40 -30 -20 1 -10 0 10 20 30 40 Temperature (°C) 50 60 70 80 Note: Typical Temperature rerating curve, refer to table for derating data 0.1 0.01 0.1 1 10 100 Current in Amperes The average time current curves and Temperature Rerating curve performance is affected by a number or variables, and these curves provided as guidance only. Customer must verify the performance in their application. 2 © 2021 Littelfuse, Inc. Specifications are subject to change without notice. Revised: GD. 05/07/21 Resettable PPTC Datasheet 30R Series Radial Leaded Soldering Parameters - Wave Soldering Soldering Zone Cooling Zone Refer to the condition recommended by the flux manufacturer. Max. ramping rate should not exceed 4°C/Sec. Max. solder temperature should not exceed 260°C. Time within 5°C of actual Max. solder temperature within 3 - 5 seconds. Total time from 25°C room to Max. solder temperature within 5 minutes including PreHeating time. Cooling by natural convection in air. Max. ramping down rate should not exceed 6°C/ Sec. Soldering 260 Cooling 220 Temperature (°C) Pre-Heating Zone 190 160 0 Preheating 60 min. 5 max. Time(s) Physical Specifications Lead Material Soldering Characteristics Insulating Material Device Labeling Environmental Specifications 0.90-1.85A: Tin-plated Copper clad steel 2.50-9.00A: Tin-plated Copper Solderability per MIL–STD–202, Method 208 Cured, flame retardant epoxy polymer meets UL94V-0 requirements. Marked with ‘LF’, voltage, current rating, and date code. Operating Temperature Maximum Device Surface Temperature in Tripped State Passive Aging Humidity Aging Thermal Shock Solvent Resistance Moisture Resistance Level 3 -40°C to +85°C 125°C +85°C, 1000 hours -/+5% typical resistance change +85°C, 85% R.H., 1000 hours -/+5% typical resistance change +85°C to -40°C 10 times -/+5% typical resistance change MIL–STD–202, Method 215 No change Level 1, J–STD–020 © 2021 Littelfuse, Inc. Specifications are subject to change without notice. Revised: GD. 05/07/21 Resettable PPTC Datasheet 30R Series Radial Leaded Dimensions & Part Marking System E A Single Sided Marking Littelfuse Trademark 30 Voltage Rating Current Rating Date Code (Contact Littelfuse for additional information) 110U XXXX B D C A F B C D E F Physical Characteristics Part Number Inches mm Inches mm Inches mm Inches mm Inches mm Inches mm Max. Max. Max. Max. Typ. Typ. Min. Min. Max. Max. Typ. Typ. Inches mm 30R090U 30R110U 30R135U 30R160U 30R185U 30R250U 30R300U 30R400U 30R500U 30R600U 30R700U 30R800U 30R900U 0.29 0.29 0.35 0.35 0.40 0.45 0.45 0.55 0.55 0.65 0.75 0.85 0.95 7.40 7.40 8.90 8.90 10.20 11.40 11.40 14.00 14.00 16.50 19.10 21.60 24.10 0.48 0.56 0.53 0.60 0.62 0.72 0.76 0.87 1.01 1.06 1.13 1.22 1.24 12.20 14.20 13.50 15.20 15.70 18.30 19.20 22.00 25.60 26.80 28.60 31.10 31.60 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.40 0.40 0.40 0.40 0.40 5.10 5.10 5.10 5.10 5.10 5.10 5.10 5.10 10.20 10.20 10.20 10.20 10.20 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 7.60 7.60 7.60 7.60 7.60 7.60 7.60 7.60 7.60 7.60 7.60 7.60 7.60 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 3.00 3.00 3.00 3.00 3.00 3.00 3.00 3.00 3.00 3.00 3.00 3.00 3.00 0.039 0.039 0.039 0.039 0.039 0.039 0.047 0.047 0.047 0.047 0.047 0.047 0.047 1.0 1.0 1.0 1.0 1.0 1.0 1.2 1.2 1.2 1.2 1.2 1.2 1.2 0.02 0.02 0.02 0.02 0.02 0.02 0.03 0.03 0.03 0.03 0.03 0.03 0.03 0.51 0.51 0.51 0.51 0.51 0.51 0.81 0.81 0.81 0.81 0.81 0.81 0.81 Lead (dia) Material Sn/CuFe Sn/CuFe Sn/CuFe Sn/CuFe Sn/CuFe Sn/Cu Sn/Cu Sn/Cu Sn/Cu Sn/Cu Sn/Cu Sn/Cu Sn/Cu Part Ordering Number System 30 R 250 U P R Packaging Style Blank: Bulk R: Tape & Ammo Series Quantity Code: F=200 H=100 M=1000 P=2000 U=500 Type: U (30vdc) IHold Current Code (See Table Below) R: Radial Voltage Rating (Vdc) 4 © 2021 Littelfuse, Inc. Specifications are subject to change without notice. Revised: GD. 05/07/21 Resettable PPTC Datasheet 30R Series Radial Leaded Packaging Part Number 30R090U 30R110U 30R135U 30R160U 30R185U 30R250U 30R300U 30R400U 30R500U 30R600U 30R700U 30R800U 30R900U I hold (A) Ordering Number 30R090UU 30R090UPR 30R110UU 30R110UPR 30R135UU 30R135UPR 30R160UU 30R160UPR 30R185UU 30R185UPR 30R250UU 30R250UPR 30R300UU 30R300UPR 30R400UF 30R400UMR 30R500UF 30R500UMR 30R600UF 30R600UMR 30R700UMR 30R800UH 30R900UH 30R900UMR I hold Code 0.90 090 1.10 110 1.35 135 1.60 160 1.85 185 2.50 250 3.00 300 4.00 400 5.00 500 6.00 600 7.00 8.00 9.00 9.00 700 800 900 900 Packaging Option Quantity Quantity & Packaging Codes Bulk Tape and Ammo Bulk Tape and Ammo Bulk Tape and Ammo Bulk Tape and Ammo Bulk Tape and Ammo Bulk Tape and Ammo Bulk Tape and Ammo Bulk Tape and Ammo Bulk Tape and Ammo Bulk Tape and Ammo Tape and Ammo Bulk Bulk Tape and Ammo 500 2000 500 2000 500 2000 500 2000 500 2000 500 2000 500 2000 200 1000 200 1000 200 1000 1000 100 100 1000 U PR U PR U PR U PR U PR U PR U PR F MR F MR F MR MR H H MR Tape and Ammo Diagram ∆h Figure 1 ∆h ∆h ∆p Reference plane A1 H1 H1 C 1 H C2 F A L H0 B W4 W5 W I2 L1 P0 D0 Direction of unreeling Cross section A - B t Reel Upper side Direction of unreeling 5 Tape © 2021 Littelfuse, Inc. Specifications are subject to change without notice. Revised: GD. 05/07/21 Resettable PPTC Datasheet 30R Series Radial Leaded Tape and Ammo Specifications Devices taped using EIA468-B/IE286-2 standards. See table below and Figure 1 for details. Dimension Carrier tape width EIA Mark IEC Mark W Dimensions Dim. (mm) Tol. (mm) W 18 -0.5 / +1.0 Hold down tape width: W4 W0 11 min. Top distance between tape edges W6 W2 3 max. Sprocket hole position W5 W1 9 -0.5 / +0.75 Sprocket hole diameter* D0 D0 4 -0.32 / +0.2 Abscissa to plane(straight lead) H H 18.5 -/+ 3.0 Abscissa to plane(kinked lead) H0 H0 16 -/+ 0.5 Abscissa to top: 30R090-30R185 H1 H1 32.2 max. - - 45.0 max. C1 - 42.5 max. Abscissa to top: 30R250-30R900 Overall width w/o lead protrusion: 30R09030R185 Overall width w/o lead protrusion: 30R25030R900 Overall width w/ lead protrusion: 30R090-30R185 - - 56 max. C2 - 43.2 max. Overall width w/ lead protrusion: 30R250-30R900 - - 57 max. Lead protrusion L1 l1 1.0 max. Protrusion of cut out L L 11 max. Protrusion beyond hold–down tape l2 l2 Not specified - Sprocket hole pitch: 30R090-30R300 P0 P0 12.7 -/+ 0.3 Sprocket hole pitch on: 30R400-30R900 P0 P0 25.4 -/+ 0.5 Device pitch: 30R090-30R300 - - 12.7 - Device pitch: 30R400-30R900 - - 25.4 - Pitch tolerance - - 20 consecutive. -/+ 1 Tape thickness t t 0.9 max. Tape thickness with splice: 30R090-30R250 t1 - 1.5 max. Tape thickness with splice: 30R300-30R900 t1 - 2.0 max. - - 0 -/+ 0.3 Body lateral deviation Δh Δh 0 -/+ 1.0 Body tape plane deviation Δp Δp 0 -/+ 1.3 Ordinate to adjacent component lead* P1 P1 3.81 -/+ 0.7 Ordinate to adjacent component lead* - - 7.62 -/+ 0.7 Splice sprocket hole alignment Lead spacing: 30R090–30R400 F F 5.08 -/+ 0.8 Lead spacing: 30R500-30R900 F F 10.18 -/+ 0.8 Note: *Differs from EIA Specification Warning • Users shall independently assess the suitability of these devices for each of their applications • Operation of these devices beyond the stated maximum ratings could result in damage to the devices and lead to electrical arcing and/or fire • These devices are intended to protect against the effects of temporary over-current or over-temperature conditions and are not intended to perform as protective devices where such conditions are expected to be repetitive or prolonged in duration • Exposure to silicon-based oils, solvents, electrolytes, acids, and similar materials can adversely affect the performance of these PPTC devices • These devices undergo thermal expansion under fault conditions, and thus shall be provided with adequate space and be protected against mechanical stresses • Circuits with inductance may generate a voltage (L di/dt) above the rated voltage of the PPTC device. Disclaimer Notice - Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of and test each product selected for their own applications. Littelfuse products are not designed for, and may not be used in, all applications. Read complete Disclaimer Notice at www.littelfuse.com/disclaimer-electronics. 6 © 2021 Littelfuse, Inc. Specifications are subject to change without notice. Revised: GD. 05/07/21