3425L300/36MR

PolySwitch® Resettable PPTC Datasheet Surface Mount PPTC 3425L Series RoHS Pb Description Littelfuse 3425L Series PPTC provides surface mount overcurrent protection for high voltage applications where resettable protection is desired. Features & Benefits ■ Compatible with high-volume electronics assembly ■ RoHS compliant and lead-free ■ Halogen-free ■ Higher voltage ratings allow use in new applications ■ High voltage ■ Low profile ■ Fast response to fault current Applications Additional Information ■ Servers and computing equipment ■ Telecom equipment protection ■ Portable electronics ■ Robotic appliances ■ Automotive electronic control module protection Resources Accessories Samples Agency Approvals Agency Agency Number E183209 R50119118 Electrical Characteristics Part Number Marking Ihold Itrip Vmax Imax Pd typ (A) (A) (Vdc) (A) (W) Maximum Time to Trip Resistance Current Time Rmin R1max (A) (Sec.) (Ω) (Ω) Agency Approvals 3425L200/60 LF200-60 2.00 4.00 60.00 20.00 2.50 8.00 10.00 0.040 0.200 X X 3425L260/60 LF260-60 2.60 5.20 60.00 20.00 2.50 8.00 10.00 0.020 0.120 X X 3425L300/36 LF300 3.00 6.00 36.00 20.00 2.50 8.00 20.00 0.010 0.060 X X Notes: Rmin = Minimum resistance of device in initial (un-soldered) state. Ihold = Hold current: maximum current device will pass without tripping in 20 °C still air Itrip = Trip current: minimum current at which the device will trip in 20 °C still air Rtyp = Typical resistance of device in initial (un-soldered) state. Vmax = Maximum voltage device can withstand without damage at rated current (Imax) R1max = Maximum resistance of device at 20 °C measured one hour after tripping or reflow soldering of 260 °C for 20 sec. Imax = Maximum fault current device can withstand without damage at rated voltage (Vmax) Caution: Operation beyond the specified rating may result in damage and possible arcing and flame. Pd = Power dissipated from device when in the tripped state at 20 °C still air 1 © 2023 Littelfuse, Inc. Specifications are subject to change without notice. Revised: GD. 05/16/23 PolySwitch® Resettable PPTC Datasheet Surface Mount PPTC 3425L Series Temperature Rerating Ambient Operation Temperature -40 ºC -20 ºC 0 ºC 20 ºC 3425L200/60 3.07 2.73 2.39 2.00 1.71 1.54 1.37 1.20 0.95 3425L260/60 4.01 3.56 3.12 2.60 2.22 2.00 1.77 1.55 1.21 3425L300/36 4.43 3.98 3.52 3.00 2.61 2.39 2.16 1.93 1.59 Part Number 40 ºC 50 ºC 60 ºC 70 ºC 85 ºC Hold Current (A) Note: Notes: The temperature rerating data is only for reference, please contact Littelfuse technical support for detail temperature rerating information. Temperature Rerating Curve Average Time Current Curves 100.00 150 3245L260/60 3245L300/36 3245L200/60 10.00 Time in Seconds Percentage of Rated Current 200 100 1.00 50 0 -40 0 40 80 0.10 120 1 10 100 Current in Amperes Temperature (ºC) Note: Typical Temperature rerating curve, refer to table for rerating data. Note: The average time current curves and Temperature Rerating curve performance is affected by a number or variables, and these curves provided as guidance only. Customer must verify the performance in their application. Soldering Perameters Pb-Free Assembly Average Ramp-Up Rate (TS(max) to TP) 3°C/second max Pre Heat: Time Maintained Above: Temperature Min (Ts(min)) 150°C Temperature Max (Ts(max)) 200°C Time (Min to Max) (ts) 60 – 180 secs Temperature (TL) 217°C Temperature (tL) 60 – 150 seconds Peak / Classification Temperature (TP) 260 °C Time within 5°C of actual peak Temperature (tp) 20 – 40 seconds Ramp-down Rate 6°C/second max Time 25°C to peak Temperature (TP) 8 minutes Max. tP TP Critical Zone TL to TP Ramp-up Temperature Profile Feature TL T S(max) tL Ramp-dow Ramp-down Preheat T S(min) tS 25 time to peak temperature Time Physical Specifications Terminal Material Lead Solderability Solder-Plated Copper (Solder Material: Matte Tin(Sn)) Meets EIA Specification RS186-9E, ANSI/J-STD-002 Category 3. 2 © 2023 Littelfuse, Inc. Specifications are subject to change without notice. Revised: GD. 05/16/23 PolySwitch® Resettable PPTC Datasheet Surface Mount PPTC 3425L Series Dimensions (mm) C A Top View 300 Bottom View 300 200 .60 B D E Inches 6.60mm (.26”) 2.50mm (.098”) A Part Number 5.30mm (.209”) Pad Layout B mm MARKING CODE VARIES WITH AMPERAGE AND VOLTAGE RATING SEE ELECTRICAL CHARACTERISTICS CHART SHOWN ARE: - 3.0 A / 36 V RATING (LEFT) - 2.0 A / 60 V RATING (RIGHT) Side View Inches C mm D Inches mm Inches E mm Inches mm Min Max Min Max Min Max Min Max Min Max Min Max Min Max Min Max Min Max Min 3425L200/60 0.33 0.35 8.30 9.00 0.24 0.26 6.00 6.70 0.04 0.07 1.00 1.80 0.01 0.10 0.30 2.50 0.01 0.03 0.25 0.65 3425L260/60 0.33 0.35 8.30 9.00 0.24 0.26 6.00 6.70 0.06 0.12 1.50 3.00 0.01 0.10 0.30 2.50 0.01 0.03 0.25 0.65 3425L300/36 0.33 0.35 8.30 9.00 0.24 0.26 6.00 6.70 0.03 0.06 0.70 1.40 0.01 0.10 0.30 2.50 0.01 0.03 0.25 0.65 Environmental Specifications Operating Temperature -40 °C to +85 °C Maximum Device Surface Temperature in Tripped State 125 °C Part Numbering System 3425 L 200/ 60 M R -A Humidity Aging Thermal Shock Solvent Resistance Vibration Moisture Sensitivity Level -A: Automotive grade Blank: Standard version Packaging Style R = Tape & Reel Series Size +85 °C, 1000 hours -/+5% typical resistance change +85 °C, 85%,R.H.,1000 hours -/+5% typical resistance change MIL–STD–202, Method 107G +85 °C / -40 °C 20 times -30% typical resistance change MIL–STD–202, Method 215 No change MIL–STD–883C, Method 2007.1, Condition A; No change Passive Aging Max L: Littelfuse Surface Mount PPTC IHOLD Hold Current Code (Refer to Electrical Characteristics Table) Quantity Code M: 1000; U: 500 Pieces /XX: Special Voltage Rating (Not applicable to all parts. Refer to Electrical Characteristics Table) Level 1, J–STD–020C Packaging Part Number Ordering Number Halogen Free I hold (A) I hold Code Voltage Option Packaging Option Quantity Quantity & Packaging Codes 3425L200/60 3425L200/60MR Yes 2.00 200 /60 Tape and Reel 1000 MR 3425L260/60 3425L260/60UR Yes 2.60 260 /60 Tape and Reel 500 UR 3425L300/36 3425L300/36MR Tape and Reel 1000 MR Yes 3.00 300 /36 3 © 2023 Littelfuse, Inc. Specifications are subject to change without notice. Revised: GD. 05/16/23 PolySwitch® Resettable PPTC Datasheet Surface Mount PPTC 3425L Series Tape and Reel Specifications TAPE SPECIFICATIONS: EIA-481-1 (mm) W REEL DIMENSIONS: EIA-481-1 (mm) 3425L200/60 3425L300/36 3425L260/60 16.0+/- 0.30 16.0+/- 0.30 C Ø180.0+/- 3.0 F 7.50+/- 0.10 7.50+/- 0.10 D Ø60+/−0.5 E1 1.75+/- 0.10 1.75+/- 0.10 H 19.5+/- 1.0 D0 1.50+ 0.10 1.50+0.10 W 17+/- 0.2 D1 1.50 (MIN) 1.50 (MIN) P0 4.0+/- 0.10 4.0+/- 0.10 P1 8.0+/- 0.10 8.0+/- 0.10 P2 2.0+/- 0.10 2.0+/- 0.10 A0 6.70+/- 0.10 6.70+/- 0.10 B0 9.50+/- 0.10 9.50+/- 0.10 T 0.30+/- 0.05 0.30+/- 0.05 KO 1.55+/-0.10 2.20+/-0.10 Leader Min. 390 390 Trailer Min. 160 160 Tape and Reel Diagram D0 P0 P1 E1 P2 H F W D T A0 C D1 K0 B0 W Warning ■ Users should independently evaluate the suitability of and test each product selected for their own application. ■ Operation beyond the maximum ratings or improper use may result in device damage and possible electrical arcing and flame. ■ These devices are intended for protection against damage caused by occasional overcurrent or overtemperature fault conditions and should not be used when repeated fault conditions or prolonged trip events are anticipated. ■ Contamination of the PPTC material with certain silicone-based oils or some aggressive solvents can adversely impact the performance of the devices. ■ Device performance can be impacted negatively if devices are handled in a manner inconsistent with recommended electronic, thermal, and mechanical procedures for electronic components. ■ PPTC devices are not recommended for installation in applications where the device is constrained such that its PTC properties are inhibited, for example in rigid potting materials or in rigid housings, which lack adequate clearance to accommodate device expansion. ■ Operation in circuits with a large inductance can generate a circuit voltage (Ldi/dt) above the rated voltage of the device. Disclaimer Notice - Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of and test each product selected for their own applications. Littelfuse products are not designed for, and may not be used in, all applications. Read complete Disclaimer Notice at http://www.littelfuse.com/disclaimer-electronics. 4 © 2023 Littelfuse, Inc. Specifications are subject to change without notice. Revised: GD. 05/16/23