8.0SMDJ45CA

TVS Diodes Surface Mount – 8000W 5000W > 8.0SMDJ 5.0SMDJ series 8.0SMDJ Series RoHS Pb e3 Description Uni-directional Bi-directional The 8.0SMDJ series is designed specifically to protect sensitive electronic equipment from voltage transients induced by lightning and other transient voltage events. Features Agency Recognitions AGENCY AGENCY FILE NUMBER E230531 Maximum Ratings and Thermal Characteristics (TA=25OC unless otherwise noted) Parameter Peak Pulse Power Dissipation at TL=25OC by 10/1000μs Waveform (Fig.2)(Note 1), (Note 2) Symbol Value Unit PPPM 8000 W Power Dissipation on Infinite Heat Sink at TL=50OC PD 6.5 W Peak Forward Surge Current, 8.3ms Single Half Sine Wave (Note 3) IFSM 300 A Maximum Instantaneous Forward Voltage at 100A for Unidirectional Only VF 5.0 V Operating Temperature Range TJ -65 to 150 °C Storage Temperature Range TSTG -65 to 175 °C Typical Thermal Resistance Junction to Lead RθJL 15 °C/W Typical Thermal Resistance Junction to Ambient RθJA 75 °C/W • For surface mounted applications to optimize board space • Low profile package • Typical failure mode is short from over-specified voltage or current • Whisker test is conducted based on JEDEC JESD201A per its table 4a and 4c • IEC-61000-4-2 ESD 30kV(Air), 30kV (Contact) • ESD protection of data lines in accordance with IEC 61000-4-2 • EFT protection of data lines in accordance with IEC 61000-4-4 • Built-in strain relief • Glass passivated chip junction • 8kW peak pulse power capability at 10/1000μs waveform, repetition rate (duty cycles):0.01% • Fast response time: typically less than 1.0ps from 0V to VBR min • Excellent clamping capability • compact size with high power density in DO214AB Package • Low incremental surge resistance • Typical IR less than 5μA when VBR min>22V • High temperature reflow soldering guaranteed: 260°C/40sec • VBR @ TJ= VBR@25°C x (1+αT x (TJ - 25)) (αT:Temperature Coefficient, typical value is 0.1%) • UL Recognized compound meeting flammability rating V-0 • Meet MSL level1, per J-STD-020, LF maximun peak of 260°C • Matte tin lead–free plated • Halogen free and RoHS compliant • Pb-free E3 means 2nd level interconnect is Pb-free and the terminal finish material is tin(Sn) (IPC/ JEDEC J-STD-609A.01) Notes: 1. Non-repetitive current pulse , per Fig. 4 and derated above TJ (initial) =25OC per Fig. 3. 2. Mounted on copper pad area of 0.31x0.31” (8.0 x 8.0mm) to each terminal. 3. Measured on 8.3ms single half sine wave or equivalent square wave for unidirectional component only,duty cycle=4 per minute maximum. Applications Functional Diagram TVS components are ideal for the protection of I/O Interfaces, VCC bus and other vulnerable circuits used in Telecom, Computer, Industrial and Consumer electronic applications. Bi-directional Cathode Anode Uni-directional ©2019 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 06/10/19 TVS Diodes Surface Mount – 8000W 5000W > 8.0SMDJ 5.0SMDJ series Electrical Characteristics (T =25°C unless otherwise noted) A Part Number (Uni) Part Number (Bi) 8.0SMDJ12A 8.0SMDJ13A 8.0SMDJ14A 8.0SMDJ15A 8.0SMDJ16A 8.0SMDJ17A 8.0SMDJ18A 8.0SMDJ20A 8.0SMDJ22A 8.0SMDJ24A 8.0SMDJ26A 8.0SMDJ28A 8.0SMDJ30A 8.0SMDJ33A 8.0SMDJ36A 8.0SMDJ40A 8.0SMDJ43A 8.0SMDJ45A 8.0SMDJ48A 8.0SMDJ51A 8.0SMDJ54A 8.0SMDJ58A 8.0SMDJ60A 8.0SMDJ64A 8.0SMDJ70A 8.0SMDJ75A 8.0SMDJ78A 8.0SMDJ85A 8.0SMDJ90A 8.0SMDJ100A 8.0SMDJ110A 8.0SMDJ12CA 8.0SMDJ13CA 8.0SMDJ14CA 8.0SMDJ15CA 8.0SMDJ16CA 8.0SMDJ17CA 8.0SMDJ18CA 8.0SMDJ20CA 8.0SMDJ22CA 8.0SMDJ24CA 8.0SMDJ26CA 8.0SMDJ28CA 8.0SMDJ30CA 8.0SMDJ33CA 8.0SMDJ36CA 8.0SMDJ40CA 8.0SMDJ43CA 8.0SMDJ45CA 8.0SMDJ48CA 8.0SMDJ51CA 8.0SMDJ54CA 8.0SMDJ58CA 8.0SMDJ60CA 8.0SMDJ64CA 8.0SMDJ70CA 8.0SMDJ75CA 8.0SMDJ78CA 8.0SMDJ85CA 8.0SMDJ90CA 8.0SMDJ100CA 8.0SMDJ110CA UNI BI Reverse Stand off Voltage VR (Volts) 8PEP 8PEQ 8PER 8PES 8PET 8PEU 8PEV 8PEW 8PEX 8PEZ 8PFE 8PFG 8PFK 8PFM 8PFP 8PFR 8PFT 8PFV 8PFX 8PFZ 8PGE 8PGG 8PGK 8PGM 8PGP 8PGR 8PGT 8PGV 8PGX 8PGZ 8PHE 8BEP 8BEQ 8BER 8BES 8BET 8BEU 8BEV 8BEW 8BEX 8BEZ 8BFE 8BFG 8BFK 8BFM 8BFP 8BFR 8BFT 8BFV 8BFX 8BFZ 8BGE 8BGG 8BGK 8BGM 8BGB 8BGR 8BGT 8BGV 8BGX 8BGZ 8BHE 12 13 14 15 16 17 18 20 22 24 26 28 30 33 36 40 43 45 48 51 54 58 60 64 70 75 78 85 90 100 110 Marking Maximum Maximum Test Clamping Maximum Clamping Maximum Maximum Agency Peak Pulse Peak Pulse Reverse Current Voltage VC Voltage VC Approval Current Ipp Current Ipp Leakage IR @ Ipp @ Ipp IT (10/1000μs) (8/20μs) @ VR (10/1000μs) (8/20μs) MAX (mA) (A) (A) (µA) (V) (V) Breakdown Voltage VBR (Volts) @ IT MIN 13.3 14.4 15.6 16.7 17.8 18.9 20.0 22.2 24.4 26.7 28.9 31.1 33.3 36.7 40.0 44.4 47.8 50.0 53.3 56.7 60.0 64.4 66.7 71.1 77.8 83.3 86.7 94.4 100.0 111.0 122.0 14.7 15.9 17.2 18.5 19.7 20.9 22.1 24.5 26.9 29.5 31.9 34.4 36.8 40.6 44.2 49.1 52.8 55.3 58.9 62.7 66.3 71.2 73.7 78.6 86.0 92.1 95.8 104.0 111.0 123.0 135.0 10 10 10 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 19.9 21.5 23.2 24.4 26.0 27.6 29.2 32.4 35.5 38.9 42.1 45.4 48.4 53.3 58.1 64.5 69.4 72.7 77.4 82.4 87.1 93.6 96.8 103.0 113.0 121.0 126.0 137.0 146.0 162.0 177.0 402.1 372.1 344.9 327.9 307.7 290.0 274.0 247.0 225.4 205.7 190.1 176.2 165.3 150.1 137.8 124.1 115.3 110.1 103.4 97.1 92.0 85.5 82.7 77.7 71.0 66.2 63.5 58.4 55.0 49.4 45.2 25.7 27.8 30.0 31.5 33.6 35.7 37.7 41.9 45.9 50.3 54.4 58.7 62.5 68.9 75.1 83.3 89.7 93.9 100.0 106.5 112.5 120.9 125.1 133.1 146.0 156.3 162.8 177.0 188.6 209.3 228.7 2613.7 2418.7 2241.9 2131.4 2000.1 1885.0 1781.0 1605.5 1464.8 1336.8 1235.7 1145.4 1074.5 975.7 895.7 806.7 749.5 715.7 671.8 631.2 598.0 555.8 537.2 504.9 461.5 430.3 412.8 379.6 357.5 321.1 293.8 800 500 200 100 50 20 10 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X For bidirectional type having VR of 20 volts and less, the IR limit is double. ©2019 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 06/10/19 TVS Diodes Surface Mount – 5000W 8000W > 5.0SMDJ 8.0SMDJ series I-V Curve Characteristics Uni-directional I I Bi-directional Ipp Vc VBR VR IR VF IT IT IR Vc VBR VR V IR IT V Ipp Ipp PPPM VR VBR VC IR VF VR VBR Vc Peak Pulse Power Dissipation -- Max power dissipation Stand-off Voltage -- Maximum voltage that can be applied to the TVS without operation Breakdown Voltage -- Maximum voltage that flows though the TVS at a specified test current (IT) Clamping Voltage -- Peak voltage measured across the TVS at a specified IPPM (peak impulse current) Reverse Leakage Current -- Current measured at VR Forward Voltage Drop for Uni-directional Ratings and Characteristic Curves (T =25°C unless otherwise noted) A Figure 1 - TVS Transients Clamping Waveform Figure 2 - Peak Pulse Power Rating 1000 PPPM-Peak Pulse Power (KW) Voltage Transients Voltage or Current Voltage Across TVS Current Through TVS TJ initial = Tamb 8kW at 10/1000µs, 25°C 100 10 1 0.001 Time 0.01 0.1 1 10 td-Pulse Width (ms) continues on next page. ©2019 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 06/10/19 TVS Diodes Surface Mount – 8000W 5000W > 8.0SMDJ 5.0SMDJ series Ratings and Characteristic Curves (T =25°C unless otherwise noted) (Continued) A Figure 3 - Peak Pulse Power Derating Curve Figure 4 - Pulse Waveform 150 80 60 40 20 0 0 25 50 75 100 125 150 TJ - Initial Junction Temperature (ºC) Transient Thermal Impedance (°C/W) Cj(pF) 2 50 10/1000µsec. Waveform as defined by R.E.A td 1.0 0 2.0 3.0 4.0 Figure 6 - Typical Transient Thermal Impedance Bi-direconal V=0V 1000 Uni/Bi-direconal V=VR 100 10 100 ( ) t-Time (ms) Uni-direconal V=0V 10 Half Value IPPM IPPM 0 100000 1 TJ=25°C Pulse Width(td) is defined as the point where the peak current decays to 50% of IPPM Peak Value IPPM 100 175 Figure 5 - Typical Junction Capacitance 10000 tr=10µsec IPPM- Peak Pulse Current, % IRSM Peak Pulse Power (PPP) or Current (IPP) Derating in Percentage % 100 1000 100 10 1 0.1 0.01 0.001 0.0001 0.001 0.01 VBR - Reverse Breakdown Voltage(V) 0.1 1 10 100 1000 TP - Pulse Duraon (s) Figure 7 - Maximum Non-Repetitive Peak Forward Surge Current Uni-Directional Only Figure 8 - Peak Forward Voltage Drop vs Peak Forward Current (Typical Values) 100.0 300 VF - Peak Forward Current(A) IFSM - Peak Forward Surve Current(A) 350 250 200 150 100 50 0 1 10 Number of cycle at 60 Hz 100 10.0 1.0 0.1 0.01 0 1 2 3 4 5 6 7 8 VF - Peak Forward Voltage(V) ©2019 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 06/10/19 TVS Diodes Surface Mount – 8000W 5000W > 8.0SMDJ 5.0SMDJ series Soldering Parameters Pre Heat Lead–free assembly - Temperature Min (Ts(min)) 150°C - Temperature Max (Ts(max)) 200°C - Time (min to max) (ts) 60 – 180 secs Ramp-up Average ramp up rate (Liquidus Temp (TA) to peak 3°C/second max TS(max) to TA - Ramp-up Rate 3°C/second max Reflow - Temperature (TL) (Liquidus) 217°C - Time (min to max) (tL) 60 – 150 seconds Peak Temperature (TP) 260 Time within 5°C of actual peak Temperature (tp) 20 – 40 seconds Ramp-down Rate 6°C/second max Time 25°C to peak Temperature (TP) 8 minutes Max. Do not exceed 260°C +0/-5 tp TP TL Temperature (T) Reflow Condition tL Ts(max) Ramp-down Ts(min) ts Preheat 25˚C t 25˚C to Peak °C Physical Specifications Weight 0.011 ounce ,0.3 grams Case JEDEC DO214AB. Molded plastic body over glass passivated junction Polarity Color band denotes positive end (cathode) except Bidirectional. Terminal Matte Tin-plated leads, Solderable per JESD22-B102 Critical Zone TL to TP Time (t) Environmental Specifications High Temp. Storage JESD22-A103 HTRB JESD22-A108 Temperature Cycling JESD22-A104 MSL JEDEC-J-STD-020, Level 1 H3TRB JESD22-A101 RSH JESD22-A111 Dimensions DO-214AB (SMC J-Bend) Cathode Band (for Uni-directional products only) C A B H D F E G J K L I Solder Pads (all dimensions in mm) Dimensions Inches Min Millimeters Max Min Max A 0.114 0.126 2.900 3.200 B 0.260 0.280 6.600 7.110 C 0.220 0.245 5.590 6.220 D 0.079 0.103 2.060 2.620 E 0.030 0.060 0.760 1.520 F - 0.008 - 0.203 G 0.305 0.320 7.750 8.130 H 0.006 0.012 0.152 0.305 I 0.129 - 3.300 - J 0.094 - 2.400 - K - 0.165 - 4.200 L 0.094 - 2.400 - ©2019 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 06/10/19 TVS Diodes Surface Mount – 8000W 5000W > 8.0SMDJ 5.0SMDJ series Part Numbering System Part Marking System 8.0SMDJ XXX C A Cathode Band F (for Uni-directional products only) 5% VBR VOLTAGE TOLERANCE BI-DIRECTIONAL VR VOLTAGE XXX SERIES YMXXX Littelfuse Logo Marking Code Trace Code Marking Y:Year Code M: Month Code XXX: Lot Code Packaging Options Component Package Part number Packaging Option Quantity Packaging Specification 8.0SMDJxxxXX DO-214AB 3000 Tape & Reel - 16mm tape/13” reel EIA STD RS-481 8.0SMDJxxxXX-T7 DO-214AB 500 Tape & Reel – 16mm tape/7” reel EIA STD RS-481 Tape and Reel Specification 0.157 (4.0) 0.63 (16.0) Cathode 0.315 (8.0) Optional 7” 7.0 (187) 13” 13.0 (330) 0.80 (20.2) Arbor Hole Dia. 0.65 (16.4) 0.059 DIA (1.5) Cover tape Dimensions are in inches (and millimeters). Direction of Feed Disclaimer Notice - Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of and test each product selected for their own applications. Littelfuse products are not designed for, and may not be used in, all applications. Read complete Disclaimer Notice at http://www.littelfuse.com/disclaimer-electronics. ©2019 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 06/10/19