80813000440

Radial Lead Fuses TE5® > Fast Acting 450V Fuse > 808 Series 808 Series TE5® Fast-Acting 450V Fuse RoHS Pb PS E Description The 450V TE5® Fast-acting Fuse is designed to enable compliance with the RoHS Directive. This product is fully compatible with lead-free solder alloy and is UL Recognized for protecting components or internal circuits against overcurrent conditions at high DC voltages. Features Agency Approvals Agency Agency File Number Ampere Range PS E NBK240118-E67006 2.00A - 5.00A E67006 2.00A - 5.00A • Reduced PCB space requirements • Direct solderable or plug-in versions • Low internal resistance • Halogen-free, lead-free, and RoHS-compliant • Shock safe casing • Vibration resistant • Antimony-free • Ideal for high voltage DC applications • Very high breaking capacity of 10kA at rated DC voltage • Recognized to UL/CSA/ NMX 248-1 and UL/CSA/ NMX 248-14 • Conforms to DENAN’s Appendix 3 Applications • DC/DC Converter • Transformer-less AC/DC Circuit Additional Information • Data Centers • Telecom/Datacom Central Offices Electrical Characteristics Datasheet Resources Samples % of Ampere Rating Opening Time 100% 4 Hours, Minimum 200% 10 Seconds, Maximum Electrical Characteristics Ampere Rating (A) Amp Code 2.00 2.50 3.00 Max Voltage Rating (V) Interrupting Rating1 AC DC 1200 250 450 1250 250 450 1300 250 350 3.15 1315 250 350 4.00 1400 250 250 5.00 1500 250 250 Nominal Cold Resistance2 (Ohms) Nominal Melting I2t 10xIN (A2sec) Max Voltage Drop 1.0xIN (mV) Agency Approval PS E 200A@250VAC 300A to 10kA@450VDC 0.069 0.0610 342 x x 0.054 0.0898 300 x x 200A@250VAC 300A to 10kA@350VDC 0.042 0.2007 276 x x 0.038 0.2191 270 x x 200A@250VAC 300A to 10kA@250VDC 0.027 0.5445 240 x x 0.022 1.1584 215 x x Notes: 1. This fuse is not recommended for use in DC circuits where the available prospective short-circuit current is less than 300A at rated voltage. 2. Cold resistance measured at less than 10% of rated current at 23°C. 3. An operating current of 80% or less of rated current is recommended, with further derating required at elevated ambient temperature. 4. Have special electrical characteristic needs? Contact Littelfuse to learn more about application specific options. © 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised: GD. 10/14/20 Radial Lead Fuses TE5® > Fast Acting 450V Fuse > 808 Series Temperature Re-rating Curve Average Time Current Curves 2.00A 2.50A 3.00A 3.15A 4.00A 5.00A 140 1000 120 80 100 23°C 60 40 10 20 0 -80 -60 -40 -20 0 20 40 60 80 100 120 140 AMBIENT TEMPERATURE (°C) Note: 1. Rerating depicted in this curve is in addition to the standard derating of 20% for continuous operation. TIME IN SECONDS PERCENT OF RATING 100 1 0.1 0.01 0.001 1 10 100 1000 CURRENT IN AMPERES Soldering Parameters - Wave Soldering 300 Recommended Process Parameters: 260 Wave Parameter 240 220 Lead-Free Recommendation Preheat: 200 180 (Depends on Flux Activation Temperature) 160 140 120 100 80 60 100°C Temperature Maximum: Preheat Time: 150°C 60-180 seconds Solder Pot Temperature: 20 240 230 220 210 200 190 180 170 160 150 140 130 110 120 90 100 80 70 60 50 40 30 20 0 0 (Typical Industry Recommendation) Temperature Minimum: 40 10 Temperature ( ) - Measured on bottom side of board 280 Solder Dwell Time: 260°C Maximum 2-5 seconds Time (Seconds) Preheat Time Cooling Time Dwell Time Recommended Hand-Solder Parameters: Solder Iron Temperature: 350°C +/- 5°C Heating Time: 5 seconds max. Note: These devices are not recommended for IR or Convection Reflow process. © 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised: GD. 10/14/20 Radial Lead Fuses TE5® > Fast Acting 450V Fuse > 808 Series Product Characteristics Materials Base/Cap: Black Thermoplastic Polyphenylene Sulfide, UL 94 V-0 Round Pins: Copper, Sn-plated Operating Temperature -65ºC to +125ºC (Consider re-rating) Product Marking Body: Brand Logo, Current Rating Rated Voltage, Characteristic “F” Moisture Resistance 10 cycles, 65°C at 90-98% R.H. over 150 minutes, 180 minutes holding time, Reduce temperature to 23 – 35°C over 150 minutes, 8 hours holding time Solderability 260ºC, ≤ 3s. (Wave) 350ºC, ≤ 1s. (Soldering Iron) Vibration Resistance Thermal Shock 50 cycles, 15 minutes at –65°C/15 minutes at 125°C (MIL-STD-202, Method 107) 24 cycles at 5 min. each (IEC60068-2-6) 10-60Hz at 0.75mm amplitude 60-2000Hz at 10G’s acceleration Dimensions Part Numbering System 4.65 8.9 max. 8.9 808 xxxx 0000 L Ø 0.6 0.5 min Series Amp Code 4.0±1.0 Holes in PCB Long Leads (L=18.8mm) Short Leads (L=4.3mm) 7.5±0.3 1 +0.1 1 +0.1 5.08 Refer to Amp Code column of Electrical Characteristics Table 0.6 4.0±0.5 Packaging Code 0000 0440 0075 Holes in PCB Tape/Ammopack Short leads - Bulk 7.5mm pitch - Bulk (1,000 pcs) (1,000 pcs) (1,000 pcs) 7.5mm Pitch Packaging Packaging Option Packaging Specification Quantity Quantity & Packaging Code Taping Width 808 Series Tape & Ammopack N/A 1,000 0000 N/A Short Leads N/A 1,000 0440 N/A 7.5 mm Pitch N/A 1,000 0075 N/A Disclaimer Notice - Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of and test each product selected for their own applications. Littelfuse products are not designed for, and may not be used in, all applications. Read complete Disclaimer Notice at: www.littelfuse.com/disclaimer-electronics. © 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised: GD. 10/14/20