A2106ZC

Four-port Balanced Three-chip Protector Four-port Balanced Three-chip Protector This hybrid Single In-line Package (SIP) protects four twisted pairs from overcurrent and overvoltage conditions. Comprised of twelve discrete DO-214AA SIDACtor devices and eight TeleLink surface mount fuses, it is ideal for densely populated line cards that cannot afford PCB inefficiencies or the use of series power resistors. Surge current ratings up to 500 A are available. Tip 5 2 Z1 13 Ring 1 Ring 6 9 18 Ring 19 Z10 11 14 F3 F1 Gnd Z7 Z4 4 Z12 Z11 Z8 Gnd 8 20 17 Z9 Z5 Gnd 3 F8 Tip 15 12 Z6 Z2 Ring Tip 10 7 Z3 Gnd F6 F4 F2 Tip 16 F5 F7 Electrical Parameters VDRM Volts Part Number * VS Volts Pins 2-3, 4-3, 7-8, 9-8, 12-13, 14-13, 17-18, 19-18 VDRM Volts VS Volts CO pF Pins 2-4, 7-9, 12-14, 17-19 VT Volts IDRM µAmps IS mAmps IT Amps IH mAmps Pins 1-3 P1553Z_ 130 180 130 180 8 5 800 2.2 150 40 P1803Z_ 150 210 150 210 8 5 800 2.2 150 40 P2103Z_ 170 250 170 250 8 5 800 2.2 150 40 P2353Z_ 200 270 200 270 8 5 800 2.2 150 40 P2703Z_ 230 300 230 300 8 5 800 2.2 150 30 P3203Z_ 270 350 270 350 8 5 800 2.2 150 30 P3403Z_ 300 400 300 400 8 5 800 2.2 150 30 A2106Z_3 ** 170 250 50 80 8 5 800 2.2 120 40 A5030Z_ 3 ** 400 550 270 340 8 5 800 2.2 150 30 * For individual “ZA,” “ZB,” and “ZC” surge ratings, see table below. ** Asymmetrical General Notes: • All measurements are made at an ambient temperature of 25 °C. IPP applies to -40 °C through +85 °C temperature range. • IPP is a repetitive surge rating and is guaranteed for the life of the product. • Listed SIDACtor devices are bi-directional. All electrical parameters and surge ratings apply to forward and reverse polarities. • VDRM is measured at IDRM. • VS is measured at 100 V/µs. • Special voltage (VS and VDRM) and holding current (IH) requirements are available upon request. • Off-state capacitance is measured between Pins 4-3 and Pins 2-3 at 1 MHz with a 2 V bias and is a typical value for “ZA” product. “ZB” and “ZC” capacitance is approximately 10 pF higher. • Device is designed to meet balance requirements of GTS 8700 and GR 974. Surge Ratings Series IPP 2x10 µs Amps IPP 8x20 µs Amps A 150 150 90 50 45 20 500 B 250 250 150 100 80 30 500 C 500 400 200 150 100 50 500 http://www.teccor.com +1 972-580-7777 IPP 10x160 µs Amps IPP 10x560 µs Amps 2 - 42 IPP 10x1000 µs Amps ITSM 60 Hz Amps di/dt Amps/µs © 2004 Teccor Electronics SIDACtor® Data Book and Design Guide Four-port Balanced Three-chip Protector Thermal Considerations Package Symbol SIP TJ Operating Junction Temperature Range Parameter -40 to +150 Value °C TS Storage Temperature Range -65 to +150 °C 90 °C/W Thermal Resistance: Junction to Ambient Data Sheets RθJA Unit +I IPP – Peak Pulse Current – %IPP +I IIT T IISS IIHH IIDRM DRM -V -V +V +V V VTT V VDRM DRM VVS S Peak Value 100 tr = rise time to peak value td = decay time to half value Waveform = tr x td 50 Half Value 0 0 tr td t – Time (µs) -I -I V-I Characteristics tr x td Pulse Waveform 6 4 IH 8 25 ˚C 2 IH (TC = 25 ˚C) 10 Ratio of Percent of VS Change – % 14 12 0 -4 2.0 1.8 1.6 1.4 1.2 25 ˚C 1.0 0.8 0.6 0.4 -40 -20 0 20 40 60 80 100 120 140 160 -6 -8 Case Temperature (TC) – ˚C -40 -20 0 20 40 60 80 100 120 140 160 Junction Temperature (TJ) – ˚C Normalized VS Change versus Junction Temperature © 2004 Teccor Electronics SIDACtor® Data Book and Design Guide Normalized DC Holding Current versus Case Temperature 2 - 43 http://www.teccor.com +1 972-580-7777