A5030UC3RP

Balanced Three-chip SIDACtor Device Balanced Three-chip SIDACtor Device 1 6 2 5 3 4 This balanced protector is a surface mount alternative to the modified TO-220 package. Based on a six-pin surface mount SOIC package, it uses Littelfuse’s patented “Y” (US Patent 4,905,119) configuration. It is available in surge current ratings up to 500 A. SIDACtor devices are used to enable equipment to meet various regulatory requirements including GR 1089, ITU K.20, K.21, and K.45, IEC 60950, UL 60950, and TIA-968-A (formerly known as FCC Part 68). Electrical Parameters Part Number * VDRM Volts VS Volts VDRM Volts Pins 1-3, 1-4 VS Volts Pins 3-4 VT Volts IDRM µAmps IS mAmps IT Amps IH mAmps CO pF P1553U_ 130 180 130 180 8 5 800 2.2 150 80 P1803U_ 150 210 150 210 8 5 800 2.2 150 80 P2103U_ 170 250 170 250 8 5 800 2.2 150 80 P2353U_ 200 270 200 270 8 5 800 2.2 150 80 P2703U_ 230 300 230 300 8 5 800 2.2 150 60 P3203U_ 270 350 270 350 8 5 800 2.2 150 60 P3403U_ 300 400 300 400 8 5 800 2.2 150 60 P5103U_ 420 600 420 600 8 5 800 2.2 150 60 A2106U_3 ** 170 250 50 80 8 5 800 2.2 120 80 A5030U_3 ** 400 550 270 340 8 5 800 2.2 150 60 * For individual “UA”, “UB”, and “UC” surge ratings, see table below. ** Asymmetrical General Notes: • All measurements are made at an ambient temperature of 25 °C. IPP applies to -40 °C through +85 °C temperature range. • IPP is a repetitive surge rating and is guaranteed for the life of the product. • Listed SIDACtor devices are bi-directional. All electrical parameters and surge ratings apply to forward and reverse polarities. • VDRM is measured at IDRM. • VS is measured at 100 V/µs. • Special voltage (VS and VDRM) and holding current (IH) requirements are available upon request. • Off-state capacitance (CO) is measured between Pins 1-3 and 1-4 at 1 MHz with a 2 V bias and is a typical value for “UA”, “UB”, and “UC” products. • Device is designed to meet balance requirements of GTS 8700 and GR 974. Surge Ratings Series IPP 2x10 µs Amps IPP 8x20 µs Amps A 150 150 90 50 45 20 500 B 250 250 150 100 80 30 500 C 500 400 200 150 100 50 500 http://www.littelfuse.com +1 972-580-7777 IPP 10x160 µs Amps IPP 10x560 µs Amps 2 - 20 IPP 10x1000 µs Amps ITSM 60 Hz Amps di/dt Amps/µs © 2004 Littelfuse, Inc. SIDACtor® Data Book and Design Guide Balanced Three-chip SIDACtor Device Thermal Considerations Package Symbol Modified MS-013 TJ Operating Junction Temperature Range -40 to +125 °C TS Storage Temperature Range -65 to +150 °C 60 °C/W 6 5 RθJA 4 Parameter Value Thermal Resistance: Junction to Ambient Unit 1 3 IPP – Peak Pulse Current – %IPP +I +I IITT ISS IH IDRM -V -V +V +V V VTT V VDRM DRM V VS S Peak Value 100 tr = rise time to peak value td = decay time to half value Waveform = tr x td 50 Half Value 0 0 tr td t – Time (µs) -I -I V-I Characteristics tr x td Pulse Wave-form IH 8 6 25 ˚C 4 2 IH (TC = 25 ˚C) 10 Ratio of Percent of VS Change – % 14 12 0 -4 2.0 1.8 1.6 1.4 25 ˚C 1.2 1.0 0.8 0.6 0.4 -40 -20 0 -6 -8 -40 -20 0 20 40 60 80 100 120 140 160 Case Temperature (TC) – ˚C 20 40 60 80 100 120 140 160 Junction Temperature (TJ) – ˚C Normalized VS Change versus Junction Temperature © 2004 Littelfuse, Inc. SIDACtor® Data Book and Design Guide Normalized DC Holding Current versus Case Temperature 2 - 21 http://www.littelfuse.com +1 972-580-7777 Data Sheets 2