AQ1003-01LTG

TVS Diode Array (SPA® Diodes) General Purpose ESD Protection - AQ1003-01LTG Series AQ1003-01LTG, 30pF 30kV Unidirectional Discrete TVS RoHS Pb GREEN Description This discrete TVS diode is fabricated in a proprietary silicon avalanche technology that protects electronic equipment I/O pins from destructive electrostatic discharges (ESDs). These robust TVSs can withstand repetitive contact or air ESD discharge events at ± 30 kV levels without suffering any performance degradation. This exceeds the ESD contact and air discharge test requirements of IEC 610004-2. Additionally, the TVS can withstand an 8/20 surge current event as defined in IEC 61000-4-5 2nd Edition up to 7A and still provide low voltage clamping levels. Features Pinout Pin 1 • ESD, IEC 61000-4-2, ±30kV contact, ±30kV air • PPAP capable • EFT, IEC 61000-4-4, 40A (5/50ns) • Moisture Sensitivity Level (MSL -1) • Lightning, 7A (8/20μs as defined in IEC 61000-4-5 2nd Edition) • Halogen free, Lead free and RoHS compliant • Low leakage current of 100nA (MAX) at 5V • AEC-Q101 qualified • ESD, ISO 10605, 330pF 330Ω, ±25kV contact, ±30kV air Pin 2 Functional Block Diagram Applications 1 • Mobile phones • Digital cameras • Smart phones • Portable medical components • PDAs • Portable navigation components • Automotive applications Application Example 2 Outside World Low - speed port I/O port Controller B1 B2 B3 B4 (4) AQ1003-01LTG Signal Ground Life Support Note: Not Intended for Use in Life Support or Life Saving Applications The products shown herein are not designed for use in life sustaining or life saving applications unless otherwise expressly indicated. © 2019 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 09/16/19 TVS Diode Array (SPA® Diodes) AQ1003-01LTG General Purpose ESD Protection - AQ1003-01LTG Series Absolute Maximum Ratings Symbol Parameter Value Units IPP Peak Pulse Current (tp=8/20μs) 7.0 A TOP Operating Temperature -40 to 150 °C TSTOR Storage Temperature -55 to 150 °C CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the component. This is a stress only rating and operation of the component at conditions above the ratings indicated in this absolute maximum ratings section or in the operational sections of this specification is not implied. Electrical Characteristics (TOP=25ºC) Parameter Symbol Reverse Standoff Voltage Test Conditions VRWM IR=1μA Breakdown Voltage VBR IR=1mA Reverse Leakage Current ILEAK Clamp Voltage1 RDYN ESD Withstand Voltage1 VESD Diode Capacitance Max 5.0 V 6.0 7.0 8.5 V VR=5V CI/O-GND 1 Typ Units 100 nA 8.5 11 V Ipp=7A tp=8/20µs, I/O to GND 11.5 14 TLP, tp=100ns, I/O to GND 0.23 Ipp=1A tp=8/20µs, I/O to GND VC Dynamic Resistance2 Min V Ω IEC 61000-4-2 (Contact Discharge) ±30 kV IEC 61000-4-2 (Air Discharge) ±30 kV Reverse Bias=0V, f=1MHz 30 35 pF Note: 1 Parameter is guaranteed by design and/or component characterization. 2 Transmission Line Pulse (TLP) with 100ns width, 2ns rise time, and average window t1=70ns to t2= 90ns Clamping Voltage vs. IPP for 8/20μs waveshape 40 14 35 12 Clamp Voltage (VC) Capacitance (pF) Capacitance vs. Reverse Bias 30 25 20 15 10 8 6 4 2 5 0 10 0 0 1 2 3 Bias Voltage (V) 4 5 1 2 3 4 5 6 7 Peak Pulse Current-IPP (A) © 2019 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 09/16/19 TVS Diode Array (SPA® Diodes) General Purpose ESD Protection - AQ1003-01LTG Series Negative Transmission Line Pulsing(TLP) Plot 20 0 15 -5 TLP Current (A) TLP Current (A) Positive Transmission Line Pulsing(TLP) Plot 10 5 -10 -15 0 0 5 10 -20 15 -10 -8 -6 -4 -2 0 TLP Voltage (V) TLP Voltage (V) 8/20μs Pulse Waveform 110% 100% 90% Percent of IPP 80% 70% 60% 50% 40% 30% 20% 10% 0% 0.0 5.0 10.0 15.0 20.0 25.0 30.0 Time (μs) Soldering Parameters Pre Heat Pb – Free assembly - Temperature Min (Ts(min)) 150°C - Temperature Max (Ts(max)) 200°C - Time (min to max) (ts) 60 – 180 secs Reflow 3°C/second max - Temperature (TL) (Liquidus) 217°C - Temperature (tL) 60 – 150 seconds Peak Temperature (TP) 260 Time within 5°C of actual peak Temperature (tp) 20 – 40 seconds Ramp-down Rate 6°C/second max Time 25°C to peak Temperature (TP) 8 minutes Max. Do not exceed 260°C +0/-5 Critical Zone TL to TP Ramp-up Average ramp up rate (Liquidus) Temp (TL) to peak 3°C/second max TS(max) to TL - Ramp-up Rate tP TP °C Temperature Reflow Condition TL T S(max) tL Ramp-dow Ramp-down Preheat T S(min) tS 25 time to peak temperature Time © 2019 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 09/16/19 TVS Diode Array (SPA® Diodes) General Purpose ESD Protection - AQ1003-01LTG Series ISO10605 (C:330pF, R:330Ω) contact discharge plot at +8KV ISO10605 (C:330pF, R:330Ω) contact discharge plot at -8KV IEC61000−4−2 +8 kV Contact ESD Clamping Voltage IEC61000−4−2 -8 kV Contact ESD Clamping Voltage Part Numbering System Product Characteristics AQ 1003 – 01 L T G Automotive Grade TVS Diode Arrays (SPA® Diodes) G= Green T= Tape & Reel Series Number of Channels Matte Tin Lead Material Copper Alloy Substrate Material Silicon Body Material Molded Compound Flammability UL Recognized compound meeting flammability rating V-0 Package L: SOD-523 Part Marking System 1 Lead Plating Ordering Information AD Part Number Package Min. Order Qty. AQ1003-01LTG SOD-523 5000 2 A = Part Code D = Date Code © 2019 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 09/16/19 TVS Diode Array (SPA® Diodes) General Purpose ESD Protection - AQ1003-01LTG Series Package Dimensions — SOD-523 E2 E Symbol 2 b D 1 Millimeters Max Min Max A 0.51 0.77 0.020 0.030 A1 0.50 0.70 0.020 0.028 b 0.25 0.35 0.010 0.014 c 0.08 0.15 0.003 0.006 D 0.70 0.90 0.028 0.035 E 1.10 1.30 0.043 0.051 E1 1.50 1.70 0.059 0.067 E1 Top View 0.20 REF E2 θ L 0.01 Ɵ 0.001 REF 0.07 0.000 7O REF 0.003 7O REF θ L c A A1 Inches Min Side View Side View 0.60mm 0.50mm 1.40mm Recommended Soldering pad layout Drawing#: L01-B Embossed Carrier Tape & Reel Specification — SOD-523 Symbol ,Ref. ,Ref. Millimeters Inches Min Max Min Max A0 0.91 1.01 0.036 0.040 B0 1.89 1.99 0.074 0.078 D0 1.50 1.60 0.059 0.063 D1 0.40 0.60 0.016 0.024 E1 1.65 1.85 0.065 0.073 F 3.40 3.60 0.134 0.142 P0 3.90 4.10 0.154 0.161 P 1.90 2.10 0.075 0.083 P1 1.95 2.05 0.077 0.081 K0 0.68 0.78 0.027 0.031 T 0.17 0.23 0.007 0.009 W 7.90 8.30 0.311 0.327 Component Orientation in Tape ,Ref. 8mm TAPE AND REEL Pin1 1 (cathode) Pin Disclaimer Notice - Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of and test each product selected for their own applications. Littelfuse products are not designed for, and may not be used in, all applications. Read complete Disclaimer Notice at http://www.littelfuse.com/disclaimer-electronics. © 2019 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 09/16/19