AQ24CANFD-02HTG

TVS Diode Arrays (SPA®® Diodes) General Purpose ESD Protection - AQ24CANFD SM24CANA AQ24CANFD 200W TVS Diode Array RoHS Pb GREEN Description The AQ24CANFD is designed to protect automotive Controller Area Network (CAN) lines from damage due to electrostatic discharge (ESD), electrical fast transient (EFT), and other overvoltage transients. The AQ24CANFD can absorb repetitive ESD strikes above the maximum level specified in the IEC 61000-4-2 international standard without performance degradation and can safely withstand 3A surge (8/20 waveshape as defined in IEC 61000-4-5 2nd edition) at a very low clamping voltages. Pinout and Functional Block Diagram 2 Features 1 • ESD, IEC 61000-4-2, ±21kV contact, ±21kV air • Low clamping voltage • EFT, IEC 61000-4-4, 50A (5/50ns) • AEC-Q101 qualified • Low leakage current • Moisture Sensitivity Level (MSL -1) • Lightning, 3A (8/20 as defined in IEC 61000-4-5 2nd edition) • Halogen free, lead free and RoHS compliant • PPAP capable Applications 3 • CAN Bus Protection • ADAS Control Units • Automotive Applications • PowerTrain Control Units • Electronic Control Units • Factory Automation • Body Control Units • Lightning Control (DALI) Application Example SPLIT CANH R T/2 CAN BUS Transceiver CAN BUS R T/2 CANL Common Mode Choke (optional) CG AQ24CANFD-02HTG Life Support Note: Not Intended for Use in Life Support or Life Saving Applications The products shown herein are not designed for use in life sustaining or life saving applications unless otherwise expressly indicated. ©2018 Littelfuse, Inc. Specifications are subject to change without notice. Revision: 01/25/18 TVS Diode Arrays (SPA®® Diodes) General Purpose ESD Protection - AQ24CANFD SM24CANA Absolute Maximum Ratings Value Units PPk Symbol Peak Pulse Power (tp=8/20μs) Parameter 200 W IPP Peak Pulse Current (tp=8/20μs) 3.0 A TOP Operating Temperature -40 to 150 °C TSTOR Storage Temperature -55 to 150 °C Notes: CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the component. This is a stress only rating and operation of the component at these or any other conditions above those indicated in the operational sections of this specification is not implied. Electrical Characteristics (TOP=25ºC) Parameter Symbol Reverse Standoff Voltage Test Conditions Min Typ 26.7 28.0 Max Units 24.0 V μA VRWM IR≤1μA, Pin1 or Pin2 to Pin3 Breakdown Voltage VBR IR=1mA, Pin1 or Pin2 to Pin3 Leakage Current ILEAK VR=24V 0.02 0.5 IPP=1A, tp=8/20µs, Pin 1 or Pin 2 to Pin 3 32.7 40.0 V IPP=3A, tp=8/20µs, Pin 1 or Pin 2 to Pin 3 41.2 50.0 V TLP, tp=100ns, I/O to GND 0.5 Clamp Voltage1 VC Dynamic Resistance2 RDYN ESD Withstand Voltage1 VESD Ω IEC 61000-4-2 (Contact Discharge) ±21 kV IEC 61000-4-2 (Air Discharge) ±21 kV 14.0 pF Reverse Bias=0V, f=1MHz; Pin 1 or Pin2 to Pin 3 CI/O-GND Diode Capacitance1 V 11.5 Note: 1 Parameter is guaranteed by design and/or component characterization. 2 Transmission Line Pulse (TLP) with 100ns width, 2ns rise time, and average window t1=70ns to t2= 90ns 8/20μs Pulse Waveform Clamping Voltage vs IPP 110% 50 100% Clamp Voltage (VC ) 90% Percent of IPP 80% 70% 60% 50% 40% 30% 20% 10% 0% 40 30 20 10 0 0.0 5.0 10.0 15.0 Time (μs) ©2018 Littelfuse, Inc. Specifications are subject to change without notice. Revision: 01/25/18 20.0 25.0 30.0 1 1.5 2 Peak Pulse Current- I PP (A) 2.5 3 TVS Diode Arrays (SPA®® Diodes) General Purpose ESD Protection - AQ24CANFD SM24CANA Capacitance vs. Reverse Bias Transmission Line Pulsing(TLP) Plot 20 12.0 TLP Current (A) Capacitance (pF) 15 8.0 4.0 10 5 0.0 0 4 8 12 16 20 24 0 Bias Voltage (V) 0 5 10 15 20 25 30 35 40 45 50 TLP Voltage (V) IEC 61000 -4-2 +8 kV Contact ESD Clamping Voltage IEC 61000 -4-2 -8 kV Contact ESD Clamping Voltage Soldering Parameters Pre Heat Pb – Free assembly 150°C - Temperature Max (Ts(max)) 200°C - Time (min to max) (ts) 60 – 180 secs Average ramp up rate (Liquidus) Temp (TL) to peak 3°C/second max TS(max) to TL - Ramp-up Rate 3°C/second max Reflow - Temperature (TL) (Liquidus) 217°C - Temperature (tL) 60 – 150 seconds Peak Temperature (TP) 260 Time within 5°C of actual peak Temperature (tp) 20 – 40 seconds Ramp-down Rate 6°C/second max Time 25°C to peak Temperature (TP) 8 minutes Max. Do not exceed 260°C ©2018 Littelfuse, Inc. Specifications are subject to change without notice. Revision: 01/25/18 +0/-5 tP TP - Temperature Min (Ts(min)) °C Temperature Reflow Condition Critical Zone TL to TP Ramp-up TL TS(max) tL Ramp-do Ramp-down Preheat TS(min) 25 tS time to peak temperature Time TVS Diode Arrays (SPA®® Diodes) General Purpose ESD Protection - SM24CANA AQ24CANFD Part Marking System Part Numbering System TVS Diode Arrays (SPA® Automotive Grade Diodes) ABVD AQ 24 CAN FD – 02 H T G G= Green T= Tape & Reel Working Voltage Package H: SOT23-3 CAN BUS Number of Channels Wattage FD: Flexible Datarate AB : Part code V : Assembly code D : Date code Product Characteristics Ordering Information Lead Plating Matte Tin Lead Material Copper Alloy Lead Coplanarity 0.004 inches(0.102mm) Substrate material Silicon Part Number Package Marking Min. Order Qty. Body Material Molded Compound AQ24CANFD-02HTG SOT23-3 ABVD 3000 Flammability UL Recognized compound meeting flammability rating V-0. Notes : 1. All dimensions are in millimeters 2. Dimensions include solder plating. 3. Dimensions are exclusive of mold flash & metal burr. Package Dimensions — SOT23-3 D Pin1 A1 A A2 E1 E Symbol Bottom View bx3 e e1 (L1) b1 (L1) c Detail A c1 L2 (gauge plane) Top View B θ L B b L Detail A Side View 2.90 0.80 1.30 0.60 1.10 2.30 Recommended soldering pad layout (unit :mm) ©2018 Littelfuse, Inc. Specifications are subject to change without notice. Revision: 01/25/18 Section B-B A A1 A2 b b1 c c1 D E E1 e e1 L L1 L2 θ Millimeters Nom Max 1.17 0.15 0.95 1.02 0.50 0.40 0.45 0.20 0.10 0.16 2.90 3.04 2.35 2.60 1.30 1.40 0.95 BSC 1.90 BSC 0.28 0.44 0.60 0.54 REF 0.25 BSC 0° 8° Min 0.89 0.01 0.88 0.30 0.30 0.08 0.08 2.80 2.10 1.20 Min 0.035 0.000 0.035 0.012 0.012 0.003 0.003 0.110 0.083 0.047 0.011 0° Inches Nom 0.037 0.016 0.004 0.114 0.093 0.051 0.037BSC 0.075BSC 0.017 0.021 REF 0.010 BSC - Max 0.046 0.006 0.040 0.020 0.018 0.008 0.006 0.120 0.102 0.055 0.024 8° TVS Diode Arrays (SPA®® Diodes) General Purpose ESD Protection - SM24CANA AQ24CANFD Embossed Carrier Tape & Reel Specification — SOT23-3 Symbol 8mm TAPE AND REEL GENERAL INFORMATION 1. 3000 PIECES PER REEL. 2. ORDER IN MULTIPLES OF FULL REELS ONLY. 3. MEETS EIA-481 REVISION "A" SPECIFICATIONS. ACCESS HOLE 14.4mm SOT23-3 (8mm POCKET PITCH) 13mm 180mm Millimetres Inches Min Max Min Max E 1.65 1.85 0.065 0.073 F 3.40 3.60 0.134 0.142 P2 1.90 2.10 0.075 0.083 0.063 D 1.40 1.60 0.055 P0 3.90 4.10 0.154 0.161 W 7.70 8.30 0.303 0.327 P 3.90 4.10 0.154 0.161 A0 3.05 3.25 0.120 0.128 B0 2.67 2.87 0.105 0.113 K0 1.12 1.32 0.044 0.052 t 0.22 0.24 0.009 0.009 60mm USER DIRECTION OF FEED PIN 1 8.4mm COVER TAPE Disclaimer Notice - Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of and test each product selected for their own applications. Littelfuse products are not designed for, and may not be used in, all applications. Read complete Disclaimer Notice at http://www.littelfuse.com/disclaimer-electronics. ©2018 Littelfuse, Inc. Specifications are subject to change without notice. Revision: 01/25/18