AQ4023-01FTG

TVS Diode Arrays (SPA®® Diodes) Lightning Surge Protection- AQ4023 SP4023 Series Series AQ4023 Series 1.3pF, 12A Discrete TVS Diode RoHS Pb GREEN Description The AQ4023 Series integrates low capacitance steering diodes with one or two avalanche breakdown diodes for unidirectional or bidirectional protection, respectively, to protect against ESD and lightning induced surge events. These components can safely absorb up to 12A per IEC 61000-4-5 2nd edition (tp=8/20μs) without performance degradation and a minimum ±30kV ESD per IEC 610004-2 International Standard. The low loading capacitance and high surge capability make it ideal for protecting telecommunication ports such as xDSL and other high voltage, high speed legacy interfaces. Pinout Features Pin 1 • ESD, IEC 61000-4-2, ±30kV contact, ±30kV air • Unidirectional and bidirectional configuration • EFT, IEC 61000-4-4, 40A (5/50ns) • Small SOD323 package fits 0805 footprints • Lightning, IEC 610004-5 2nd edition, 12A (tP=8/20μs) • AEC-Q101 qualified • Low capacitance of 1.3pF (@ VR=0V) • Halogen free, lead free and RoHS compliant • Moisture Sensitivity Level(MSL -1) • Low leakage current Pin 2 Cathode polarity for unidirectional only Functional Block Diagram Applications 1 1 • xDSL Interfaces • Medical Equipment • RS-232 • RS-485 • Computers and Peripherals • Power Ports • CAN Bus protection • Security Equipment • Automotive applications • Instrumentation 2 2 Unidirectional SP4023-01FTG SP4021-01FTG AQ4023-01FTG Bidirectional SP4023-01FTG-C SP4021-01FTG-C AQ4023-01FTG-C Life Support Note: Not Intended for Use in Life Support or Life Saving Applications The products shown herein are not designed for use in life sustaining or life saving applications unless otherwise expressly indicated. ©2018 Littelfuse, Inc. Specifications are subject to change without notice. Revision: 03/07/18 TVS Diode Arrays (SPA®® Diodes) Lightning Surge Protection- AQ4023 SP4023 Series Absolute Maximum Ratings Symbol Parameter Value IPP Peak Current (tp=8/20μs) PPk Peak Pulse Power (tp=8/20μs) TOP TSTOR Units 12 A 450 W Operating Temperature -40 to 150 °C Storage Temperature -55 to 150 °C Notes: CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the component. This is a stress only rating and operation of the component at these or any other conditions above those indicated in the operational sections of this specification is not implied. Electrical Characteristics (TOP=25ºC) Parameter Symbol Test Conditions Min Reverse Standoff Voltage VRWM IR≤1μA with Pin 1 to Pin 2 Breakdown Voltage VBD IT=1mA with Pin 1 to Pin 2 Leakage Current ILEAK VR=15V with Pin 1 to Pin 2 Typ VC Dynamic Resistance2 RDYN ESD Withstand Voltage1 VESD Diode Capacitance1 CD Units 15 V 16 V 0.1 IPP=1A, tp=8/20µs, Fwd Clamp Voltage1 Max μA 23 V IPP=2A, tp=8/20µs, Fwd 24 V IPP=10A, tp=8/20µs, Fwd 35 V IPP=12A, tp=8/20µs, Fwd 37.5 V TLP tp=100ns, Pin 1 to Pin 2 0.55 Ω IEC 61000-4-2 (Contact Discharge) ±30 kV IEC 61000-4-2 (Air Discharge) ±30 kV Reverse Bias=0V, f=1MHz, Pin 1 to Pin 2 1.3 2 pF Note: 1Parameter is guaranteed by design and/or component characterization. 2 Transmission Line Pulse (TLP) test setting : Std.TDR(50Ω),tp=100ns, tr=0.2ns ITLP and VTLP averaging window: start 1=70ns to end t2=80ns 8/20μs Pulse Waveform Capacitance vs. Reverse Bias (Pin 1 to Pin 2) 110% 3.0 100% 2.5 90% Capacitance (pF) Percent of IPP 80% 70% 60% 50% 40% 30% 1.5 1.0 0.5 20% 10% 0% 2.0 0.0 0.0 5.0 10.0 15.0 Time (μs) ©2018 Littelfuse, Inc. Specifications are subject to change without notice. Revision: 03/07/18 20.0 25.0 30.0 0 1.5 3 4.5 6 7.5 9 Bias Voltage (V) 10.5 12 13.5 15 TVS Diode Arrays (SPA®® Diodes) Lightning Surge Protection- SP4023 AQ4023 Series Series Clamping Voltage vs. Peak Pulse Current (Pin 1 to Pin 2) Transmission Line Pulsing (TLP) Plot (Pin 1 to Pin2) 25 45.0 40.0 20 30.0 TLP Current (A) Clamp Voltage (VC ) 35.0 25.0 20.0 15.0 15 10 10.0 5 5.0 0.0 1 2 3 4 5 6 7 8 9 10 11 0 12 0 Peak Pulse Current -I PP (A) 10 20 30 40 50 TLP Volts (V) Soldering Parameters Pre Heat Pb – Free assembly - Temperature Min (Ts(min)) 150°C - Temperature Max (Ts(max)) 200°C - Time (min to max) (ts) 60 – 180 secs Average ramp up rate (Liquidus) Temp (TL) to peak 3°C/second max TS(max) to TL - Ramp-up Rate 3°C/second max Reflow - Temperature (TL) (Liquidus) - Temperature (tL) tP TP Temperature Reflow Condition TL TS(max) tL Ramp-do Ramp-down Preheat TS(min) tS 217°C 60 – 150 seconds Peak Temperature (TP) 260+0/-5 °C Time within 5°C of actual peak Temperature (tp) 20 – 40 seconds Ramp-down Rate 6°C/second max Time 25°C to peak Temperature (TP) 8 minutes Max. Do not exceed 260°C 25 time to peak temperature Revision: 03/07/18 Time Product Characteristics Lead Plating Matte tin Lead Material Copper Alloy Lead Coplanarity 0.0004 inches (0.102mm) Substrate material Silicon Body Material Molded Compound Flammability UL Recognized compound meeting flammability rating V-0 Notes : 1. All dimensions are in millimeters 2. Dimensions include solder plating. 3. Dimensions are exclusive of mold flash & metal burr. ©2018 Littelfuse, Inc. Specifications are subject to change without notice. Critical Zone TL to TP Ramp-up TVS Diode Arrays (SPA®® Diodes) AQ4023 Series Series Lightning Surge Protection- SP4023 Part Marking System Part Numbering System AQ 4023 – 01 F T G – C AQ4023-01FTG SP4023-01FTG Blank = Unidirectional C= Bidirectional Automotive Grade TVS Diode Arrays (SPA® Diodes) 15 Series Number of Channels 2 1 G= Green T= Tape & Reel AQ4023-01FTG-C SP4023-01FTG-C Package F: SOD323 Ordering Information 15C 1 2 Part Number Package Marking Min. Order Qty. AQ4023-01FTG SOD323 15 3000 AQ4023-01FTG-C SOD323 15C 3000 Package Dimensions -SOD323 E A2 A1 SOD323 D b Symbol A L1 Recommended Solder Pad 1.79 0.49 c 0.45 0.2 E1 1.14 Millimeters Inches Min Max Min Max A 0.80 1.00 0.031 0.039 A1 0.00 0.10 0.000 0.004 A2 0.80 0.90 0.031 0.035 b 0.25 0.35 0.010 0.014 c 0.08 0.15 0.003 0.006 D 1.20 1.40 0.047 0.055 E 1.60 1.80 0.063 0.071 E1 2.50 2.70 0.098 0.106 L1 0.25 0.40 0.010 0.016 2.28 2.77 Unit: mm Embossed Carrier Tape & Reel Specification — SOD323 Symbol ,Ref. ,Ref. Component Orientation in Tape 8mm TAPE AND REEL Millimeters A0 1.46+/-0.10 B0 2.90+/-0.10 W 8.0+0.3/-0.10 D0 1.50+0.10 D1 0.45min/1.15max E1 1.75+/-0.10 E2 - F 3.50+/-0.10 P0 4.00+/-0.10 P 4.00+/-0.10 P1 2.00+/-0.05 K0 1.25+/-0.10 T 0.254+/-0.02 ,Ref. Pin1 Disclaimer Notice - Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of and test each product selected for their own applications. Littelfuse products are not designed for, and may not be used in, all applications. Read complete Disclaimer Notice at http://www.littelfuse.com/disclaimer-electronics. ©2018 Littelfuse, Inc. Specifications are subject to change without notice. Revision: 03/07/18