BDB Series
Standard Profile DIP Switches
NEW
Features/Benefits
•
Traditional full profile DIP switch
•
Extended actuator for easy actuation
•
Special sealed construction allows for
H
DIP
solder washing without the need for
tape seal
• RoHS compatible and compliant
• New generation price competitive
Specifications
(except 11 position).
SOLDERABILITY: Per MIL-STD-202F method 208D, or EIA RS-186E
method 9 (1 hour steam aging).
CONTACT RATING:
Carry: 100 mA max. @ 50 V DC.
Switch: 100 mA max. @ 5 V DC or 25 mA max. @ 25 V DC.
MECHANICAL AND ELECTRICAL LIFE: 10,000 make-and-break
cycles at full load, each circuit.
CONTACT RESISTANCE: Below 50 milliohms typ. initial
numerous applications
VIBRATION: No contact opening greater than 10 microseconds and no
contact closure when exposed to vibration .06 in DA or 5g, whichever is less, from 10 to 55 Hz, and 10g from 55 to 500 Hz.
SWITCH FUNCTION: SPST - 2 thru 12 position available
Typical Applications
•
Address switch for industrial controls
•
Logic switching for computers and peripherals
•
Function controlling for
Materials
@ 2-4 V DC 100mA.
INSULATION RESISTANCE: 109 ohms min.
ON
PACKAGING: Switches supplied in rigid dispensing tubes in full-tube
quantities only: this may effect order quantity. Number of switches
per tube varies with model. Switch position 1 denotes pin number
1. All switch actuators in ‘OFF’ position, standard.
2. Option for “ON” is available on volume demand.
HOUSING: PA46, color red (UL94V-0)
BDB
DIELECTRIC STRENGTH: 300 V RMS min. @ sea level between
adjacent terminals.
1 2 adjacent
3 4 5 terminals.
6 7 8
CAPACITANCE: 5pF max. between
COVER: Glass filed polyester (PBT) (UL94V-0)
ACTUATOR: Glass filed polyester (PBT) (UL94V-0)
CONTACTS: Gold plate phosphor bronze
STORAGE & OPERATING TEMPERATURE: -40°C to 85°C.
TERMINALS: Gold plate over nickel plated brass
SHOCK: Withstands 20g 11 ms sawtooth waveform with no contact opening greater than 10 microseconds.
Note: Specifications and materials listed above are for switches with standard options.
For information on specific and custom switches, consult Customer Service Center.
Vertical Full Profile DIP
QUANTITY
PER TUBE
PART NUMBER
NO.POS.
DIM. ‘A’ DIM. ‘B’
ON
BDB
1 2 3 4 5 6 7 8
BDB08
BDB02
BDB03
BDB04
BDB05
DATE CODE: YEAR+WEEK
BDB06
YEAR: The letter «A» means 2009,
«B»
means 2010..., «J» means 2018, and so on
BDB07
WEEK: «01» means the first week «01»
means the second week, and BDB08
so on
BDB09
BDB10
BDB12
2
.280 (7,11)
.100 (2,54)
70
3
.380 (9,65)
.200 (5,08)
51
4
.480 (12,19)
.300 (7,62)
40
5
.580 (14,73)
.400 (10,16)
33
6
.680 (17,27)
.500 (12,75)
28
7
.780 (19,81)
.600 (15,24)
24
8
.880 (22,35)
.700 (17,78)
21
9
.980 (24,89)
.800 (20,32)
19
10
1.080 (27,43)
.900 (22,.86)
17
12
1.280 (32,51)
1.100 (27,94)
14
Schematic
SPST
DATE CODE: YEAR+WEEK
YEAR: The letter «A» means 2009, «B»
means 2010..., «J» means 2018, and so on
WEEK: «01» means the first week «01»
means the second week, and so on
Dimensions are shown: Inch (mm)
Specifications and dimensions subject to change
16 may 2019
H–22
www.ckswitches.com
BDB Series
Standard Profile DIP Switches
NEW
Installation, Soldering and Cleaning
All BDB Series Standard Profile DIP Switches can be hand soldered or machine soldered without the use of boot, caps,
tapes or special attention. Closed base washable models have unique design, allowing solvent cleaners and water / detergent solutions to flush and clean the electrical contacts of the contaminants and fluxes. For best results, follow these
directions :
Dimensions are shown: Inch (mm)
Specifications and dimensions subject to change
16 may 2019
H–23
www.ckswitches.com
DIP
1) Wave soldering recommended at 500° F (260°C) solder temperature.
2) Hand solder using 30 watt small tip iron controlled at 500° F (260°C), 10 seconds max./terminal.
3) The bottom is sealed with resin to prevent flux penetration during wave soldering.
4) All switch actuators must be in ‘OFF’ position during soldering and cleaning processes.
5) If there is still a presence of flux, clean the flux using forced rinse, high agitation or triple bath cleaning method. Do not
mask or cover the switch in any way during cleaning.
H
很抱歉,暂时无法提供与“BDB05”相匹配的价格&库存,您可以联系我们找货
免费人工找货