FDA215S

FDA215 MOSFET Driver INTEGRATED CIRCUITS DIVISION Parameter Typical Open Circuit Voltage Typical Short Circuit Current Input Control Current Rating 5.5 2.5 5 Units V A mA Features • Optically Isolated, Input to Output • Dual Independent, Floating Outputs for Parallel, Series, or Isolated Configuration • 5mA Control Current • May Be Configured for AC and DC Switching • Replacement of Discrete Components • VDE Compatible • Solid State Reliability • No EMI/RFI Generation • Surface Mount and Tape & Reel Version Available • Flammability Rating UL 94 V-0 Applications • MOSFET Driver • Programmable Control • Process Control • Instrumentation • Telecommunications Description The FDA215 is a dual photovoltac MOSFET driver that uses a pair of optically coupled LEDs to drive two photodiode arrays. When the input current is applied to the LED, the light emitted activates the photodiode array, and generates a voltage at the output. The photodiode arrays are capable of generating a floating source voltage and current sufficient to drive high power MOSFET transistors. The optical coupling provides a high level of input to output isolation. The FDA215 is well suited for use in discrete solid state relay designs and other isolated switching applications. Approvals • EN/IEC 60950-1 Certified Component: Certificate available on our website Ordering Information Part # FDA215 FDA215S FDA215STR Description 8-Pin DIP (50/tube) 8-Pin Surface Mount (50/tube) 8-Pin Surface Mount (1000/reel) Pin Configuration 1 Input 2 3 Input 4 DS-FDA215-R07 www.ixysic.com + – PV – 8 Output + 7 + – PV – + 6 Output 5 1 INTEGRATED CIRCUITS DIVISION FDA215 Absolute Maximum Ratings @ 25ºC Parameter Reverse Input Voltage Input Control Current Peak (10ms) Input Power Dissipation 1 Total Power Dissipation 2 Capacitance, Input to Output Isolation Voltage, Input to Output Operational Temperature Storage Temperature 1 Derate linearly 1.33 mW / ºC 2 Derate linearly 6.67 mW / ºC Ratings 5 100 1 150 500 1 3750 -40 to +85 -40 to +125 Units V mA A mW mW pF Vrms °C °C Absolute Maximum Ratings are stress ratings. Stresses in excess of these ratings can cause permanent damage to the device. Functional operation of the device at conditions beyond those indicated in the operational sections of this data sheet is not implied. Typical values are characteristic of the device at +25°C, and are the result of engineering evaluations. They are provided for information purposes only, and are not part of the manufacturing testing requirements. Electrical Characteristics @ 25ºC Parameter Output Characteristics Open Circuit Voltage Short Circuit Current Switching Speeds Turn-On Turn-Off Offstate Clamping Resistance Input Characteristics Input Control Current Input Voltage Drop Reverse Input Current Common Characteristics Capacitance, Input to Output 2 Conditions Symbol Min Typ Max Units IF=5mA IF=5mA IF=25mA VOC 5.5 2.5 3.5 8 9 20 V ISC 3 1 2.5 VL=1V ton toff RCL 100 250 5 5 3300 IF=5mA VR=5V IF VF IR 0.9 - 1.2 - 5 1.5 10 mA V µA VIO=0V, f=1MHz CIO - 3 - pF IF=5mA, CLOAD=200pF www.ixysic.com A ms  R07 INTEGRATED CIRCUITS DIVISION FDA215 PERFORMANCE DATA* LED Forward Voltage vs. Forward Current (Room Temperature) LED Forward Voltage Drop vs. Temperature 1.5 1.5 1.4 1.3 1.2 IF=5mA 1.1 740 1.4 1.3 1.2 1.1 -20 0 20 40 60 Temperature (ºC) 80 700 700 Turn-On Time (Ps) 800 600 85ºC 25ºC 0ºC -40ºC 300 200 20 30 40 50 60 IF=20mA 200 10 15 20 25 30 35 40 45 50 55 LED Current (mA) IF=50mA -20 0 20 40 60 Temperature (ºC) 80 -40ºC 0ºC 25ºC 85ºC 300 200 0 10 20 30 40 LED Current (mA) 50 200 150 100 50 0 0.250 0.200 0.150 -20 0 20 40 60 Temperature (ºC) 80 100 0 6 IF=5mA 5 4 20 40 60 Temperature (ºC) 80 100 4000 6000 Capacitance (pF) 8000 10000 Output Current vs. Output Voltage IF=10mA 15 10 IF=5mA 5 2.5 2.0 1.5 -40ºC 0ºC 25ºC 85ºC 1.0 0.5 0.0 0 0 2000 3.0 Load Current (mA) IF=10mA 7 10000 12000 0.225 Short Circuit Current vs. Temperature Short Circuit Current (PA) 8 4000 6000 8000 Capacitance (pF) IF=50mA IF=20mA IF=10mA IF=5mA 0.275 20 9 2000 0.175 0 -40 60 10 -20 4 0.300 IF=50mA IF=20mA IF=10mA IF=5mA Open Circuit Voltage vs. Temperature -40 6 Turn-Off Time vs. Capacitance (VOUT=1V) 100 0 8 100 Turn-Off Time (ms) Turn-Off Time (Ps) 600 100 2 250 800 700 80 IF=5mA IF=10mA IF=20mA IF=50mA 10 Turn-Off Time vs. Temperature (VOUT=1V, COUT=200pF) 900 20 40 60 Temperature (ºC) 0 -40 Turn-Off Time vs. LED Current (VOUT=1V, C=200pF) 400 0 12 IF=10mA 300 0 500 -20 Turn-On Time vs. Capacitance (VOUT=5V) 14 400 0 Open Circuit Voltage (V) -40 IF=5mA 500 100 5 10 600 100 0 640 Turn-On Time vs. Temperature (VOUT=5V, COUT=200pF) 900 400 660 LED Forward Current (mA) 800 500 680 600 0 100 Turn-On Time vs. LED Current (VOUT=5V, C=200pF) 900 700 Turn-On Time (ms) -40 720 620 1.0 1.0 Turn-On Time (Ps) 760 On-Resistance (:) IF=50mA IF=20mA IF=10mA LED Forward Voltage (V) LED Forward Voltage (V) 1.6 Turn-Off Time (Ps) On-Resistance vs. Temperature (VLOAD=1V, Internal to Photovoltaic Driver) -40 -20 0 20 40 60 Temperature (ºC) 80 100 0 1 2 3 4 Load Voltage (V) 5 6 *Unless otherwise noted, data presented in these graphs is typical of device operation at 25ºC. For guaranteed parameters not indicated in the written specifications, please contact our application department. R07 www.ixysic.com 3 INTEGRATED CIRCUITS DIVISION FDA215 Manufacturing Information Moisture Sensitivity All plastic encapsulated semiconductor packages are susceptible to moisture ingression. IXYS Integrated Circuits classifies its plastic encapsulated devices for moisture sensitivity according to the latest version of the joint industry standard, IPC/JEDEC J-STD-020, in force at the time of product evaluation. We test all of our products to the maximum conditions set forth in the standard, and guarantee proper operation of our devices when handled according to the limitations and information in that standard as well as to any limitations set forth in the information or standards referenced below. Failure to adhere to the warnings or limitations as established by the listed specifications could result in reduced product performance, reduction of operable life, and/or reduction of overall reliability. This product carries a Moisture Sensitivity Level (MSL) classification as shown below, and should be handled according to the requirements of the latest version of the joint industry standard IPC/JEDEC J-STD-033. Device Moisture Sensitivity Level (MSL) Classification FDA215 / FDA215S MSL 1 ESD Sensitivity This product is ESD Sensitive, and should be handled according to the industry standard JESD-625. Soldering Profile Provided in the table below is the Classification Temperature (TC) of this product and the maximum dwell time the body temperature of this device may be (TC - 5)ºC or greater. The classification temperature sets the Maximum Body Temperature allowed for this device during lead-free reflow processes. For through-hole devices, and any other processes, the guidelines of J-STD-020 must be observed. Device Classification Temperature (Tc) Dwell Time (tp) Max Reflow Cycles FDA215S FDA215 250ºC 250ºC 30 seconds 30 seconds 3 1 Board Wash IXYS Integrated Circuits recommends the use of no-clean flux formulations. Board washing to reduce or remove flux residue following the solder reflow process is acceptable provided proper precautions are taken to prevent damage to the device. These precautions include, but are not limited to: using a low pressure wash and providing a follow up bake cycle sufficient to remove any moisture trapped within the device due to the washing process. Due to the variability of the wash parameters used to clean the board, determination of the bake temperature and duration necessary to remove the moisture trapped within the package is the responsibility of the user (assembler). Cleaning or drying methods that employ ultrasonic energy may damage the device and should not be used. Additionally, the device must not be exposed to flux or solvents that are Chlorine- or Fluorine-based. 4 www.ixysic.com R07 INTEGRATED CIRCUITS DIVISION FDA215 MECHANICAL DIMENSIONS FDA215S 9.652 ± 0.381 (0.380 ± 0.015) 2.540 ± 0.127 (0.100 ± 0.005) 0.635 ± 0.127 (0.025 ± 0.005) 3.302 ± 0.051 (0.130 ± 0.002) 9.525 ± 0.254 (0.375 ± 0.010) 6.350 ± 0.127 (0.250 ± 0.005) Pin 1 0.457 ± 0.076 (0.018 ± 0.003) PCB Land Pattern 2.54 (0.10) 8.90 (0.3503) 1.65 (0.0649) 7.620 ± 0.254 (0.300 ± 0.010) 0.254 ± 0.0127 (0.010 ± 0.0005) 0.65 (0.0255) 4.445 ± 0.127 (0.175 ± 0.005) Dimensions mm (inches) 0.813 ± 0.102 (0.032 ± 0.004) FDA215STR Tape & Reel 330.2 DIA. (13.00 DIA.) Top Cover Tape Thickness 0.102 MAX. (0.004 MAX.) K0 =4.90 (0.193) Ao=10.30 (0.406) K1 =4.20 (0.165) Embossed Carrier Embossment R07 W=16.00 (0.63) Bo=10.30 (0.406) P1=12.00 (0.472) User Direction of Feed Dimensions mm (inches) NOTES: 1. Dimensions carry tolerances of EIA Standard 481-2 2. Tape complies with all “Notes” for constant dimensions listed on page 5 of EIA-481-2 www.ixysic.com 5 INTEGRATED CIRCUITS DIVISION FDA215 FDA215 2.540 ± 0.127 (0.100 ± 0.005) 9.652 ± 0.381 (0.380 ± 0.015) 8-0.800 DIA. (8-0.031 DIA.) 2.540 ± 0.127 (0.100 ± 0.005) 9.144 ± 0.508 (0.360 ± 0.020) 6.350 ± 0.127 (0.250 ± 0.005) Pin 1 PCB Hole Pattern 7.620 ± 0.254 (0.300 ± 0.010) 0.457 ± 0.076 (0.018 ± 0.003) 4.064 TYP (0.160) 3.302 ± 0.051 (0.130 ± 0.002) 7.239 TYP. (0.285) 7.620 ± 0.127 (0.300 ± 0.005) 0.254 ± 0.0127 (0.010 ± 0.0005) 7.620 ± 0.127 (0.300 ± 0.005) Dimensions mm (inches) 0.813 ± 0.102 (0.032 ± 0.004) For additional information please visit our website at: www.ixysic.com IXYS Integrated Circuits makes no representations or warranties with respect to the accuracy or completeness of the contents of this publication and reserves the right to make changes to specifications and product descriptions at any time without notice. Neither circuit patent licenses nor indemnity are expressed or implied. Except as set forth in IXYS Integrated Circuits' Standard Terms and Conditions of Sale, IXYS Integrated Circuits assumes no liability whatsoever, and disclaims any express or implied warranty, relating to its products including, but not limited to, the implied warranty of merchantability, fitness for a particular purpose, or infringement of any intellectual property right. The products described in this document are not designed, intended, authorized or warranted for use as components in systems intended for surgical implant into the body, or in other applications intended to support or sustain life, or where malfunction of IXYS Integrated Circuits' product may result in direct physical harm, injury, or death to a person or severe property or environmental damage. IXYS Integrated Circuits reserves the right to discontinue or make changes to its products at any time without notice. 6 Specification: DS-FDA215-R07 ©Copyright 2018, IXYS Integrated Circuits OptoMOS® is a registered trademark of IXYS Integrated Circuits All rights reserved. Printed in USA. 6/21/2018 The information below supercedes any previously presented material. For additional information please visit our website at: https://www.littelfuse.com Disclaimer Notice - Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of and test each product selected for their own applications. Littelfuse products are not designed for, and may not be used in, all applications. Read complete Disclaimer Notice at www.littelfuse.com/disclaimer-electronics.