HQ6025KH5TP

Teccor® brand Thyristors 25 Amp High Temperature Alternistor Triacs HQ6025xH5 Series RoHS Description The HQ6025xH5 is a 25 Amp bi-directional Alternistor Triac that is designed for AC switching and phase control applications that require a higher temperature environment. Alternistor type devices only operate in quadrants I, II, & and are used in circuits requiring high dv/dt capability. Features & Benefits • 150°C maximum junction temperature • Voltage capability up to 600 V • RoHS-compliant • Surge capability up to 300 A • Glass – passivated junctions Agency Approval Agency Applications Excellent for high-temperature environments applications where available heat-sinking is minimal such as heating and white goods. Agency File Number E71639* Internally constructed isolated packages are offered for ease of heat sinking with highest isolation voltage. * - L and K Packages Only Main Features Symbol Additional Information Value Unit IT(RMS) 25 A VDRM / VRRM 600 V IGT 50 mA Datasheet Resources Samples Schematic Symbol MT2 MT1 G © 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised: BO.12/11/20 Teccor® brand Thyristors 25 Amp High Temperature Alternistor Triacs Absolute Maximum Ratings Symbol Parameter IT(RMS) ITSM Test Conditions RMS on-state current Peak non-repetitive surge current HQ6025LH5 TC = 95°C HQ6025RH5 HQ6025NH5 HQ6025KH5 TC = 102°C - Value Unit 25 A full cycle; f = 50Hz; TJ (initial) = 25°C 250 full cycle; f = 60Hz; TJ (initial) = 25°C 300 A I2t I2t Value for fusing tp = 8.3ms 373 A2s di/dt Critical rate-of-rise of on-state current f = 60Hz; TJ =150°C 100 A/μs IGTM Peak gate current TJ = 150°C 2 A PG(AV) Average gate power dissipation TJ = 150°C 0.5 W Tstg Storage temperature range - -40 to 150 °C TJ Operating junction temperature range - -40 to 150 °C Electrical Characteristics (TJ = 25°C, unless otherwise specified) Symbol Test Conditions Quadrant Value Unit 50 mA MAX. 1.3 V MIN. 0.2 V MAX.. 80 mA IGT VD = 12V RL = 60 Ω I – II – III MAX. VGT VD = 12V RL = 60 Ω I – II – III VGD VD = VDRM RL = 3.3 kΩ TJ = 150°C I – II – III IH IT = 400mA (initial) dv/dt VD = VDRM; gate open; TJ = 150°C MIN 350 V/μs (dv/dt)c (di/dt)c = 13.3 A/ms; TJ = 150°C MIN 20 V/μs IG = 2 x IGT PW = 15µs IT = 35.4A TYP. 3 μs tgt Static Characteristics Symbol VTM IDRM / IRRM Test Conditions IT = 35.4A; tp = 380 μs MAX. TJ = 25°C VDRM / VRRM TJ = 150°C Value Unit 1.4 V 5 MAX. μA 6000 Thermal Resistances Symbol Rθ(J-C) Rθ(J-A) Parameter Junction to case (AC) Junction to ambient Value HQ6025LH5 2.0 HQ6025RH5 HQ6025NH5 0.86 HQ6025KH5 1.35 HQ6025LH5 50 HQ6025RH5 45 Unit °C/W °C/W Note: xx = voltage © 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised: BO.12/11/20 Teccor® brand Thyristors 25 Amp High Temperature Alternistor Triacs Figure 1: Normalized DC Gate Trigger Current vs. Junction Temperature Figure 2: N  ormalized DC Gate Trigger Voltage vs. Junction Temperature 2.0 2.0 Ratio of VGT / VGT(TJ = 25°C) Ratio of IGT / IGT(TJ = 25°C) 2.5 1.5 1.0 0.5 0.0 1.5 1.0 0.5 0.0 -40 -15 10 35 60 85 110 135 -40 150 -15 10 Junction Temperature (TJ) -- (°C) Figure 3: Normalized DC Holding Current vs. Junction Temperature Instantaneous On-state Current (iT) – Amps Ratio of IH / IH(TJ = 25°C) 1.5 1.0 0.5 0.0 -15 10 35 60 85 110 135 150 35 30 25 20 15 10 5 0 20 25 150 80 70 60 50 40 30 20 10 0 0.7 Maximum Allowable Case Temperature (TC) - °C Average On-State Power Dissipation [PD(AV)] -- Watts 40 15 135 0.8 0.9 1.0 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 Figure 6: M  aximum Allowable Case Temperature vs. RMS On-State Current 45 10 110 Instantaneous On-state Voltage (vT) – Volts Figure 5: Power Dissipation (Typical) vs. RMS On-State Current 5 85 90 Junction Temperature (TJ) -- (°C) 0 60 Figure 4: O  n-State Current vs. On-State Voltage (Typical) 2.0 -40 35 Junction Temperature (TJ) -- (°C) 30 RMS On-State Current [IT(RMS)] -- Amps 35 40 160 HQ6025RH5 HQ6025NH5 HQ6025KH5 140 120 HQ6025LH5 100 80 60 40 CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 360° 20 0 0 5 10 15 20 25 30 RMS On-State Current [IT(RMS)] - Amps © 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised: BO.12/11/20 Teccor® brand Thyristors 25 Amp High Temperature Alternistor Triacs Figure 7: Maximum Allowable Case Temperature vs. Average On-State Current Maximum Allowable Ambient Temperature (TA) - °C 160 CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 180° FREE AIR RATING 140 120 100 80 60 40 20 0 0.0 0.5 1.0 1.5 2.0 2.5 3.0 RMS On-State Current [IT(RMS)] -- Amps Figure 8: Surge Peak On-State Current vs. Number of Cycles Peak Surge (Non-repetitive) On-state Current (ITSM) – Amps 1000 SUPPLY FREQUENCY: 60 Hz Sinusoidal LOAD: Resistive RMS On-State Current: [IT(RMS)]: Maximum Rated Value at Specified Case Temperature Notes: 1. Gate control may be lost during and immediately following surge current interval. 2. Overload may not be repeated until junction temperature has returned to steadystate rated value. 100 10 1 10 100 1000 Surge Current Duration -- Full Cycles © 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised: BO.12/11/20 Teccor® brand Thyristors 25 Amp High Temperature Alternistor Triacs Soldering Parameters Pb – Free assembly Pre Heat - Temperature Min (Ts(min)) 150°C - Temperature Max (Ts(max)) 200°C - Time (min to max) (ts) 60 – 180 secs Average ramp up rate (Liquidus Temp) (TL) to peak 5°C/second max TS(max) to TL - Ramp-up Rate 5°C/second max Reflow - Temperature (TL) (Liquidus) 217°C - Temperature (tL) 60 – 150 seconds Peak Temperature (TP) 260 Time within 5°C of actual peak Temperature (tp) 20 – 40 seconds Ramp-down Rate 5°C/second max Time 25°C to peak Temperature (TP) 8 minutes Max. Do not exceed 280°C +0/-5 tP TP °C Physical Specifications Terminal Material Copper Alloy Terminal Finish 100% Matte Tin Plated Body Material UL Recognized epoxy meeting flammability classification 94V-0 Design Considerations Careful selection of the correct device for the application’s operating parameters and environment will go a long way toward extending the operating life of the Thyristor. Good design practice should limit the maximum continuous current through the main terminals to 75% of the device rating. Other ways to ensure long life for a power discrete semiconductor are proper heat sinking and selection of voltage ratings for worst case conditions. Overheating, overvoltage (including dv/dt), and surge currents are the main killers of semiconductors. Correct mounting, soldering, and forming of the leads also help protect against component damage. Temperature Reflow Condition Ramp-up TL tL TS(max) Preheat TS(min) 25 Ramp-do Ramp-down tS time to peak temperature Time Environmental Specifications Test Specifications and Conditions High Temperature Voltage Blocking MIL-STD-750: Method 1040, Condition A Rated VRRM, 150°C, 1008 hours Temperature Cycling MIL-STD-750: Method 1051 -40°C to 150°C, 15-minute dwell, 100 cycles Biased Temp & Humidity EIA/JEDEC: JESD22-A101 320VDC, 85°C, 85%RH, 1008 hours High Temp. Storage MIL-STD-750: Method 1031 150°C, 1008 hours Low-Temp Storage -40°C, 1008 hours Resistance to Solder Heat MIL-STD-750: Method 2031 260°C, 10 seconds Solderability ANSI/J-STD-002, Category 3, Test A Lead Bend MIL-STD-750: Method 2036, Condition E © 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised: BO.12/11/20 Teccor® brand Thyristors 25 Amp High Temperature Alternistor Triacs Dimensions — TO-220AB (R-Package) — Non-Isolated Mounting Tab Common with Center Lead TC MEASURING POINT O A ØE AREA (REF.) 0.17 IN2 Dimension 8.13 .320 P MT2 A B C 13.36 .526 D 7.01 .276 NOTCH IN GATE LEAD TO ID. NON-ISOLATED TAB F R G L H N K J Note: Maximum torque to be applied to mounting tab is 8 in-lbs. (0.904 Nm.) M MT1 MT2 GATE Inches Millimeters Min Max Min Max 0.380 0.420 9.65 10.67 B 0.105 0.115 2.67 2.92 C 0.230 0.250 5.84 6.35 D 0.590 0.620 14.99 15.75 E 0.142 0.147 3.61 3.73 F 0.110 0.130 2.79 3.30 G 0.540 0.575 13.72 14.61 H 0.025 0.035 0.64 0.89 J 0.195 0.205 4.95 5.21 K 0.095 0.105 2.41 2.67 L 0.060 0.075 1.52 1.91 M 0.085 0.095 2.16 2.41 N 0.018 0.024 0.46 0.61 O 0.178 0.188 4.52 4.78 P 0.045 0.060 1.14 1.52 R 0.038 0.048 0.97 1.22 Min Max Min Max 0.380 0.420 9.65 10.67 Dimensions — TO- 220AB (L Package) — Isolated Mounting Tab TC MEASURING POINT O A ØE P AREA (REF.) 0.17 IN2 8.13 .320 A B C 13.36 .526 D 7.01 .276 F R G Dimension Inches Millimeters B 0.105 0.115 2.67 2.92 C 0.230 0.250 5.84 6.35 D 0.590 0.620 14.99 15.75 E 0.142 0.147 3.61 3.73 F 0.110 0.130 2.79 3.30 G 0.540 0.575 13.72 14.61 H 0.025 0.035 0.64 0.89 J 0.195 0.205 4.95 5.21 K 0.095 0.105 2.41 2.67 L L 0.060 0.075 1.52 1.91 H M 0.085 0.095 2.16 2.41 K N J MT1 MT2 GATE M Note: Maximum torque to be applied to mounting tab is 8 in-lbs. (0.904 Nm.) N 0.018 0.024 0.46 0.61 O 0.178 0.188 4.52 4.78 P 0.045 0.060 1.14 1.52 R 0.038 0.048 0.97 1.22 © 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised: BO.12/11/20 Teccor® brand Thyristors 25 Amp High Temperature Alternistor Triacs Dimensions — TO- 218AC (K Package) — Isolated Mounting Tab Dimension TC Measurement Point U (diameter) B C D A F E W Gate J P MT1 MT2 H M Q R G N Note: Maximum torque to be applied to mounting tab is 8 in-lbs. (0.904 Nm). K L Millimeters Max Min Max 0.810 0.835 20.57 21.21 B 0.610 0.630 15.49 16.00 C 0.178 0.188 4.52 4.78 D 0.055 0.070 1.40 1.78 E 0.487 0.497 12.37 12.62 16.64 A M Package MT2 / Anode Inches Min F 0.635 0.655 16.13 G 0.022 0.029 0.56 0.74 H 0.075 0.095 1.91 2.41 15.88 J 0.575 0.625 14.61 K 0.211 0.219 5.36 5.56 L 0.422 0.437 10.72 11.10 M 0.058 0.068 1.47 1.73 N 0.045 0.055 1.14 1.40 P 0.095 0.115 2.41 2.92 Q 0.008 0.016 0.20 0.41 0.41 R 0.008 0.016 0.20 U 0.159 0.163 4.04 4.14 W 0.085 0.095 2.17 2.42 Min Max Min A 0.360 0.370 9.14 9.40 B 0.380 0.420 9.65 10.67 Dimensions — TO-263AB (N-Package) — D2 -PAK Surface Mount TC MEASURING POINT B Dimension AREA: 0.11 IN2 C V E MT2 7. 01 .276 A 8.41 .331 S W U G J K GATE MT1 H D 8.13 .320 F 2.16 .085 11.68 .460 7. 01 .276 7. 01 .276 16.89 .665 8.89 .350 Inches Millimeters Max C 0.178 0.188 4.52 4.78 D 0.025 0.035 0.64 0.89 E 0.045 0.060 1.14 1.52 F 0.060 0.075 1.52 1.91 G 0.095 0.105 2.41 2.67 H 0.092 0.102 2.34 2.59 0.61 J 0.018 0.024 0.46 K 0.090 0.110 2.29 2.79 S 0.590 0.625 14.99 15.88 V 0.035 0.045 0.89 1.14 U 0.002 0.010 0.05 0.25 W 0.040 0.070 1.02 1.78 1.40 .055 3.81 .150 2.03 .080 6.60 .260 Product Selector Part Number Voltage Gate Sensitivity Package - 50 mA TO-220R - 50 mA TO-263 - - 50 mA TO-220L - - 50 mA TO-218K 400V 600V 800V 1000V HQ6025RH5 - X - HQ6025NH5 - X - HQ6025LH5 - X HQ6025KH5 - X © 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised: BO.12/11/20 Teccor® brand Thyristors 25 Amp High Temperature Alternistor Triacs Packing Options Part Number Marking Weight Packing Mode Base Quantity HQ6025RH5TP HQ6025RH5 2.2g Tube 1000 (50 per tube) 1000 (50 per tube) HQ6025NH5TP HQ6025NH5 1.6g Tube HQ6025NH5RP HQ6025NH5 1.6g Embossed Carrier 500 HQ6025LH5TP HQ6025LH5 2.2g Tube 1000 (50 per tube) HQ6025KH5TP HQ6025KH5 4.4g Tube 250 (25 per tube) TO-263 Embossed Carrier Reel Pack (RP) Specifications Meets all EIA-481-2 Standards 0.63 (16.0) 0.157 (4.0) Gate 0.059 DI A (1.5) MT1 0.945 (24.0) 0.827 * (21.0) * Co ver tape MT2 12.99 (330.0) 0.512 (13.0) Arbor Hole Dia. Dimensions are in inches (and millimeters). 1.01 (25.7) Direction of Feed Part Numbering System Part Marking System TO-220 AB - (L and R Package) TO-263 AB - (N Package) HQ 60 25 L H5 81 DEVICE TYPE HQ: Triac VOLTAGE RATING 60: 600V LEAD FORM DIMENSIONS xx: Lead Form Option SENSITIVITY & TYPE H5: 50mA HQ6025RH5 YMXXX TO-218AC - (K Package) HQ6025KH5 YMLXX ® CURRENT RATING 25: 25A PACKAGE TYPE L: TO-220 AB (Isolated) K: TO-218 AC (Isolated) R: TO-220AB (Non-isolated) N: TO-263 (D2 Pak) Date Code Marking Y:Year Code M: Month Code XXX: Lot Trace Code Date Code Marking Y:Year Code M: Month Code L: Location Code XX: Lot Serial Code Disclaimer Notice - Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of and test each product selected for their own applications. Littelfuse products are not designed for, and may not be used in, all applications. Read complete Disclaimer Notice at www.littelfuse.com/disclaimer-electronics. © 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised: BO.12/11/20