ITV4030L1212

POLYSWITCH® Battery Protector Surface Mount > ITV4030 Series ITV4030 12A Series Description ITV4030 Series is a three terminals surface mountable battery protector which is designed to against both overcurrent and overvoltage (overcharging). A fuse element is embedded to cut off the circuit when overcurrent issue happens. A heater is also directly embedded under the fuse element, it will generate heat to blow the fuse once overvoltage detected by IC or FET. Features • Halogen Free AGENCY • Protection for both overcurrent and overcharging • Surface Mount Agency Approvals AGENCY FILE NUMBER AMPERE RANGE TBD TBD TBD TBD Applications Thermal Derating Characteristics Ambient Operating Temperature Recommend Rated Current (A) • Fast response 25°C 40°C 60°C 13.5 12.0 10.0 • Notebook • Automotive applications • Cell phone • Printer • Camera • Security systems • Ultrabook • Power tools • Tablet PC • Ecall Electrical Characteristics Part Number Ordering Code Irated (A) Vmax (Vdc) Ibreak (A) VOP (V) Agency Approvals Resistance Rheater (Ω) Rfuse (mΩ) 3.0 ~ 4.5 0.6 ~ 1.5 0.018 X X ITV4030L0412 ITV4030L0412NR 12 36 50 ITV4030L0812 ITV4030L0812NR 12 36 50 4.0 ~ 9.0 2.0 ~ 3.2 0.010 X X ITV4030L1212 ITV4030L1212NR 12 36 50 7.4 ~ 13.8 2.0 ~ 3.2 0.0085 X X ITV4030L1412 ITV4030L1412NR 12 36 50 0.010 X X 10.5 ~ 19.6 11.2 ~ 20.0 Current Capacity 100% x Irated No Melting Cut Time 200% x Irated < 1 min Interrupting Current 5 x Irated, power on 5 ms, power off 995 ms, 10000 cycles No Melting Over Voltage Operation In operation voltage range, the fusing time is ITV4030 Series Cut Time by Heater Operation Various heater wattage at 25ºC ambient temperature Constant heater wattage at various ambient temperature 10 10 Cut Time (s) Cut Time (s) 1 1 6W 35W 0.1 0.1 0 10 20 Power (W) 30 0.01 40 -20 0 20 40 60 80 100 Ambient Temperature ι ( ºC) Cut Time by Current Operation Various interrupting current at 25ºC ambient temperature Constant 2x rated current at various ambient temperature 100 100 Cut Time (s) Cut Time (s) 10 1 0.1 10 0.01 0.001 1 0 50 100 150 200 Interrupting Current (A) -20 0 20 40 60 80 100 Ambient Temperature (°C) Environmental Specifications Storage Temperature 0~35ºC, ≤70%RH 3 months after shipment Operating Temperature -10ºC to +65ºC Operating Electric Power -25ºC to +85ºC/6~35W (applied to heater) Hot Passive Aging 100±5ºC, 250 hours No structural damage and functional failure Humidity Aging 60ºC±2ºC, 90~95% R.H. 250 hours No structural damage and functional failure Cold Passive Aging -20±3ºC, 500 hours No structural damage and functional failure Thermal Shock MIL-STD-202 Method 107G +125ºC/-55ºC, 100 times No structural damage and functional failure Solvent Resistance MIL-STD-202, Method 215 Vibration MIL-STD-883C, Method 2007.1, Condition A No structural damage and functional failure © 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 01/22/20 POLYSWITCH® Battery Protector Surface Mount > ITV4030 Series Physical Dimension (mm) Device Circuit 3 3 Fuse B 2 2 Heater Fuse C A 1 A1 A2 B1 B4 B5 A3 A4 A5 4.00 ± 0.3 B 3.00 ± 0.2 C 0.90 max A1 0.58 ± 0.1 A2 0.50 ± 0.1 A3 1.26 ± 0.1 A4 1.35 ± 0.1 A5 0.67 ± 0.1 B1 0.80 ± 0.1 B2 1.44 ± 0.1 B3 1.03 ± 0.1 B4 0.96 ± 0.1 B5 1.03 ± 0.1 B3 B2 A 1 Board and Solder Layout Recommend (mm) B1 B3 B4 B2 B5 A1 A2 A3 Physical Specifications Glass Epoxy PCB Material Base Thickness 0.6mm Copper Thickness 0.07mm Covered Wire AWG18 A1 1.20 ± 0.1 A2 1.55 ± 0.1 A3 2.40 ± 0.1 B1 1.20 ± 0.1 B2 1.60 ± 0.1 B3 1.55 ± 0.1 B4 0.90 ± 0.1 B5 1.55 ± 0.1 Soldering Parameters 3ºC/second max. Preheat Temperature Min (Tsmin) 150ºC Temperature Max (Tsmax) 200ºC Time (Tsmin to Tsmax) 60-120 seconds Temperature (TL) 217ºC Time maintained above: Time (tL) 60-105 seconds Peak Temperature (TP) 255ºC Time within 5ºC of actual Peak Temperature (tP) 5 seconds max. Ramp-Down Rate 6ºC/second max. Time 25ºC to Peak Temperature 8 minutes max. © 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 01/22/20 tP TP Critical Zone tL to tP Ramp-up TL TS(max) Temperature Average Ramp-Up Rate (Tsmax to TP) tL Ramp-do Ramp-down TS(min) 25 Preheat tS time to peak temperature Time -- All temperature refer to topside of the package, measured on the package body surface -- If reflow temperature exceeds the recommended profile, devices may not meet the performance requirements -- Recommended reflow methods: IR, vapor phase oven, hot air oven, N2 environment for lead -- Recommended maximum paste thickness is 0.25mm (0.010inch) -- Devices can be cleaned using standard industry methods and solvents -- Devices can be reworked using the standard industry practices POLYSWITCH® Battery Protector Surface Mount > ITV4030 Series Part Numbering System Part Marking System LF   ITV 4030 L 04 12 NR SERIES COMPANY SYMBOL DEVICE SIZE L: 4.0mm W: 3.0mm OPERATING VOLTAGE COMPANY SYMBOL RATED CURRENT RATED VOLTAGE 4V RATED CURRENT 12A TAPE/REEL 5000/Reel Packaging Part Number ITV4030LXX12 Tape and Reel Quantity 5,000 Installation and Handling Guidelines • Before and after mounted, the ultrasonic-cleaning or immersion-cleaning must not be done to ITV device. The flux on element would flow, and it would not be satisfied its specification when cleaning is done. In addition, a similar influence happens when the product comes in contact with cleaning solution. These products after cleaning will not be guaranteed. • Silicone-based oils, oils, solvents, gels, electrolytes, fuels, acids, and similar will adversely affect the properties of ITV devices, and shall not be used or applied. • Please DO NOT reuse the ITV device removed by the soldering process. • ITV devices are secondary protection devices and are used solely for sporadic, accidental overcurrent or overtemperature error condition, and shall NOT be used if or when constant or repeated fault conditions (such fault conditions may be caused by, among others, incorrect pin-connection of a connector) or over-extensive trip events may occur. • Operation over the maximum rating or other forms of improper use may cause failure, arcing, flame and/or other damage to the ITV devices. • The performance of ITV devices will be adversely affected if they are improperly used under electronic, thermal and/or mechanical procedures and/or conditions non-conformant to those recommended by manufacturer. • Customers shall be responsible for determining whether it is necessary to have back-up, failsafe and/or fool-proof protection to avoid or minimize damage that may result from extra-ordinary, irregular function or failure of ITV devices. • There should be minimum of 0.1mm spacing between ITV and surrounding compounds, to maintain the product characteristics and avoid damage other surrounding compounds. • This product is designed and manufactured only for general-use of electronics devices. We do not recommend that it is used for the applications military, medical and so on which may cause direct damages on life, bodies or properties. © 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 01/22/20 POLYSWITCH® Battery Protector Surface Mount > ITV4030 Series Tape and Reel Specifications (mm) W 12.0 ± 0.30 F 5.50 ± 0.05 E1 1.75 ± 0.10 D0 1.55 ± 0.05 D1 1.50 ± 0.10 P0 4.00 ± 0.10 P1 8.00 ± 0.10 P2 2.00 ± 0.10 A0 3.32 ± 0.10 B0 4.32 ± 0.10 T 0.23 ± 0.05 K0 1.3 ± 0.10 H 16.5 ± 0.1 W 12.5 ± 1.5 D Ø62.5 ± 0.5 C Ø330 ± 1.0 Disclaimer Notice - Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of and test each product selected for their own applications. Littelfuse products are not designed for, and may not be used in, all applications. Read complete Disclaimer Notice at www.littelfuse.com/disclaimer-electronics. © 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 01/22/20