LCE60A

TVS Diodes Axial Leaded – 1500W > 1.5KE series LCE Series RoHS Pb e3 Description The LCE Series is designed specifically to protect sensitive electronic equipment from voltage transients induced by lightning and other transient voltage events. Features Agency Approvals Agency Agency File Number E230531 Maximum Ratings and Thermal Characteristics (TA=25OC unless otherwise noted) Parameter Symbol Value Unit Peak Pulse Power Dissipation by 10/1000μs Test Waveform (Fig.1)(Note 1) PPPM 1500 W PD 6.5 W TJ , TSTG -65 to 175 °C Steady State Power Dissipation on Infinite Heat Sink at TL=75ºC (Fig. 5) Operating Junction and Storage Temperature Range Note: 1. Non-repetitive current pulse , per Fig. 3 and derated above TJ (initial) = 25OC per Fig. 2. • 1500W peak pulse power capability at 10/1000μs waveform, repetition rate (duty cycles):0.01% • Glass passivated chip junction in DO-201 Package • Fast response time: typically less than 1.0ps from 0 Volts to BV min • Excellent clamping capability • Typical failure mode is short from over-specified voltage or current • Whisker test is conducted based on JEDEC JESD201A per its table 4a and 4c • IEC-61000-4-2 ESD 30kV(Air), 30kV (Contact) • ESD protection of data lines in accordance with IEC 61000-4-2 • EFT protection of data lines in accordance with IEC 61000-4-4 • Low incremental surge resistance • High temperature to reflow soldering guaranteed: 260°C/40sec / 0.375”,(9.5mm) lead length, 5 lbs., (2.3kg) tension • Plastic package is flammability rated V-0 per Underwriters Laboratories • Matte tin lead–free plated • Ideal for data line applications • Halogen free and RoHS compliant • Pb-free E3 means 2nd level interconnect is Pb-free and the terminal finish material is tin(Sn) (IPC/JEDEC J-STD609A.01) Applications Additional Infomarion TVS devices are ideal for the protection of I/O interfaces, VCC bus and other vulnerable circuits used in telecom, computer, industrial and consumer electronic applications. Datasheet Resources Samples © 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised: BA.08/31/20 TVS Diodes Axial Leaded – 1500W > 1.5KE series Electrical Characteristics (T =25°C unless otherwise noted) A Part Number Reverse Stand off Voltage VR (V) LCE6.5A LCE7.0A LCE7.5A LCE8.0A LCE8.5A LCE9.0A LCE10A LCE11A LCE12A LCE13A LCE14A LCE15A LCE16A LCE17A LCE18A LCE20A LCE22A LCE24A LCE26A LCE28A LCE30A LCE33A LCE36A LCE40A LCE43A LCE45A LCE48A LCE51A LCE54A LCE58A LCE60A LCE64A LCE70A LCE75A LCE85A LCE90A 6.5 7.0 7.5 8.0 8.5 9.0 10.0 11.0 12.0 13.0 14.0 15.0 16.0 17.0 18.0 20.0 22.0 24.0 26.0 28.0 30.0 33.0 36.0 40.0 43.0 45.0 48.0 51.0 54.0 58.0 60.0 64.0 70.0 75.0 85.0 90.0 Breakdown Voltage VBR (V) Min. Max. 7.22 7.98 7.78 8.60 8.33 9.21 8.89 9.83 9.44 10.40 10.00 11.10 11.10 12.30 12.20 13.50 13.30 14.70 14.40 15.90 15.60 17.20 16.70 18.50 17.80 19.70 18.90 20.90 20.00 22.10 22.20 24.50 24.40 26.90 26.70 29.50 28.90 31.90 31.10 34.40 33.30 36.80 36.70 40.60 40.00 44.20 44.40 49.10 47.80 52.80 50.00 55.30 53.30 58.90 56.70 62.70 60.00 66.30 64.40 71.20 66.70 73.70 71.10 78.60 77.80 86.00 83.30 92.10 94.40 104.00 100.00 111.00 Test Current IT (mA) 10 10 10 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Maximum Reverse Leakage IR @ VR (µA) 1000 500 250 100 50 10 5 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Maximum Clamping Voltage at Ipp VC (V) 11.2 12.0 12.9 13.6 14.4 15.4 17.0 18.2 19.9 21.5 23.2 24.4 26.0 27.6 29.2 32.4 35.5 38.9 42.1 45.5 48.4 53.3 58.1 64.5 69.4 72.7 77.4 82.4 87.1 93.6 96.8 103.0 113.0 121.0 129.0 146.0 Working Peak Inverse Maximum Maximum Inverse Inverse Blocking Peak Pulse Junction Blocking Blocking Leakage Current Capacitance @ Voltage VWIB Current at IIB Voltage (Fig.3) 0 Volts (pF) @ VWIB (mA) VPIB (V) (V) IPPM (A) 100.0 100.0 100.0 100.0 100.0 97.0 88.0 82.0 75.0 70.0 65.0 61.0 57.0 54.0 51.0 46.0 42.0 39.0 36.0 33.0 31.0 28.1 25.8 23.3 21.6 20.6 19.4 18.2 17.2 16.0 15.5 14.6 13.3 12.4 11.6 10.3 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 75 75 75 75 75 75 75 75 75 75 75 75 75 75 75 75 75 75 75 75 75 75 75 75 75 75 75 75 100 100 100 100 125 125 125 125 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 125 125 125 125 150 150 150 150 Agency Approval X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X Note: For parts without A, the VBR is ±10% and VC is 5% higher than with A parts, the parts without A are currently available, but not recommended for new designs. The parts with A are preferred. © 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised: BA.08/31/20 TVS Diodes Axial Leaded – 1500W > 1.5KE series Ratings and Characteristic Curves (T =25°C unless otherwise noted) A Figure 1 - Peak Pulse Power Rating Figure 2 - Peak Pulse Power Derating Curve 1000 100 Peak Pluse Power(PPP) or Current(IPP) Derating in Percentage % PPPM - Peak Pulse Power (kW) 100% 10 1 80% 60% 40% 20% 0% 0.1 0.000001 0.00001 0.0001 SMF5.0 ~ SMF100 SMF110 ~ SMF250 0 25 50 75 100 125 150 175 0.001 TJ Initial Junction Temperature(˚C) td-Pluse Width (Sec.) Figure 3 - Pulse Waveform Figure 4 - AC Line Protection Application IPPM- Peak Pulse Current, % IRSM 150 tr=10µsec TJ=25°C Pulse Width(td) is defined as the point where the peak current decays to 50% of IPPM Peak Value IPPM 100 Half Value IPPM IPPM ( ) 2 50 0 10/1000µsec. Waveform as defined by R.E.A Low Capacitance TVC td 0 1.0 2.0 t-Time (ms) 3.0 4.0 Application Note: Device must be used with two units in parrellel, opposite in polarity as shown on circuit for AC signal lin protection. © 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised: BA.08/31/20 TVS Diodes Axial Leaded – 1500W > 1.5KE series Soldering Parameters Lead–free assembly Pre Heat - Temperature Min (Ts(min)) 150°C - Temperature Max (Ts(max)) 200°C - Time (min to max) (ts) 60 – 180 secs Ramp-up Average ramp up rate (Liquidus Temp (TA) to peak 3°C/second max TS(max) to TA - Ramp-up Rate 3°C/second max Reflow tp TP - Temperature (TA) (Liquidus) 217°C - Time (min to max) (ts) 60 – 150 seconds Peak Temperature (TP) 260+0/-5 °C Time within 5°C of actual peak Temperature (tp) 20 – 40 seconds Ramp-down Rate 6°C/second max Time 25°C to peak Temperature (TP) 8 minutes Max. Do not exceed 260°C TL Temperature (T) Reflow Condition tL Ts(max) Ramp-down Ts(min) ts Preheat 25˚C t 25˚C to Peak Time (t) Flow/Wave Soldering (Solder Dipping) Peak Temperature : 265OC Dipping Time : 10 seconds Soldering : 1 time Environmental Specifications Physical Specifications Weight 0.045oz., 1.2g High Temp. Storage JESD22-A103 Case JEDEC DO-201 molded plastic body over passivated junction. HTRB JESD22-A108 Polarity Color band denotes the cathode except Bipolar. Matte Tin axial leads, solderable per JESD22-B102. Temperature Cycling JESD22-A104 H3TRB JESD22-A101 RSH JESD22-B106 Terminal Critical Zone TL to TP Dimensions Dimensions Cathode Band D (for uni-directional products only) C A B Inches Millimeters Min Max Min A 1.000 - 25.40 Max - B 0.285 0.375 7.20 9.50 C 0.038 0.042 0.96 1.07 D 0.190 0.210 4.80 5.30 A DO-201 © 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised: BA.08/31/20 TVS Diodes Axial Leaded – 1500W > 1.5KE series Part Numbering System Part Marking System Option Code: Blank Reel Tape -B Bulk Packaging Cathode Band F LCE xxx A X YYWW Littelfuse Logo Type Code: A Uni-Directional (5% VBR Voltage Tolerance) Trace Code Marking LCEXXX VR Voltage Code: (Refer to the Electrical Characteristics table) YY:Year Code WW: Week Code Product Type Series Code: Packaging Part Number LCExxxXX LCExxxXX-B Schematic Component Quantity Package DO-201 1200 DO-201 500 Packaging Option Tape & Reel Packaging Specification EIA STD RS-296 BULK Littelfuse Spec. Transient Voltage Suppressor Diode Tape and Reel Specification Off Center either side 0.028(0.7) 2.56 (65.0) 0.236 (6.0) 0.047 (1.2) 0.394+/-0.020 (10.0+/-0.5) 13.0 (330.2) 2.063+0.079/-0.039 (53.0+2.0/-1.0) Dimensions are in inches/mm 3.0 (76.2) 0.68 (17.27) 2.75 (69.85) Recess Depth Max. 0.75 (19.05) Direction of Feed Disclaimer Notice - Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of and test each product selected for their own applications. Littelfuse products are not designed for, and may not be used in, all applications. Read complete Disclaimer Notice at www.littelfuse.com/disclaimer-electronics. © 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised: BA.08/31/20