LSP05480LLP

Surge Protection Module LED Lighting Surge Protection Module > LSP05 LSP05 Module Series RoHS Description The Littelfuse LSP05 thermally protected Surge Protective Device is a self-protected device which is specially designed to be used in outdoor and commercial LED lighting fixtures for transient overvoltage protection. It is constructed with Littelfuse thermally protected varistor technology. Its built-in thermal disconnect function provides additional protection to prevent catastrophic failure and fire hazard even under the extreme circumstances of varistor end-of-life or sustaining over voltage conditions. The LSP05 facilitates customer’s product compliance to IEEE C62.41.2 Location Category C Low and US Dept of Energy MSSLC Model Spec. Agency Approvals Agency Features Standard Agency File Number UL1449 E320116 Applications • Outdoor and Commercial LED Lighting • Roadway lighting • Traffic lighting • Digital signage • • • • • Wash wall lighting Parking garage/lot lighting Flood lighting Tunnel lighting Street lighting Additional Information Resources Datasheet Samples • Maximum Discharge Current, 10kA, 8/20us • Meets ANSI C82.775-2015: Location Category CM, 10kV/5kA, 1.2/50µS-8/20µS Combination Wave. • Meets IEEE C62.41.2: Location Category CLow, 6kV/3kA, 1.2/50µS-8/20µS Combination Wave. • Meets US Dept. of Energy MSSLC Model Spec. • Parallel connected SPD device • Thermally protected Varistor technology • IP66 Water-proof and Dust-proof • Indication wire lead options for Parallel connected modules • UL 1449 Type 4 Component Assembly Recognition (Type 4CA) • IEC61643-11 Class II/ EN61643-11 Type 2 Compliant1 • Compact form factor (48x48x30mm) with mounting tabs • 240Vac and 277Vac voltage ratings are available for Class I and Class II installation based on IEC luminaire protection classes • CE - Meets the requirements of Low Voltage and RoHS European Directives. Notes: 1. Self-declared compliance. Absolute Maximum Ratings • For ratings of individual members of a series, see Device Ratings and Specifications chart LSP05 Series Units 150 to 510 V A Continous Steady State Applied Voltage: Max AC Voltage Range (VM(AC)RMS) Transient Maximum Discharge Current 8/20μs Waveform (Imax) 10,000 Nominal Discharge Current 8/20µs Waveform (In) 5,000 A Operating Ambient Temperature Range (TA) -45 to +85 °C Storage Temperature Range (TSTG) -45 to +125 °C Isolation Voltage Capability (When the thermal disconnect opens) Insulation Resistance 600 V >1,000 MΩ CAUTION: Stresses above those listed in "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. © 2019 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 11/04/19 Surge Protection Module LED Lighting Surge Protection Module > LSP05 LSP05 Series Device Ratings & Specifications Part Number7 Operating Voltage (VAC) Maximum Discharge Current (Imax)(A)2 MCOV/Uc (VAC)5 Nominal Discharge Current (In)(A)1 LSP05120* 120 150 10,000 5,000 LSP05240* 240 275 10,000 5,000 LSP05277* 277 320 10,000 5,000 LSP05347* 347 420 10,000 5,000 LSP05480* 480 510 10,000 5,000 10,000 5,000 LSP05240LL* LSP05480LL* L-L:240 L-L:275 L-N/G:120 L-N/G:150 L-L:480 L-L:510 L-N/G:277 L-N/G:320 10,000 5,000 MLV (V)3 Safety Compliance Up (V)4 L-N:680 L-G:680 N-G:630 L-N:1070 L-G:1050 N-G:1020 L-N:1260 L-G:1280 N-G:1220 L-N:1590 L-G:1590 N-G:1570 L-N:1780 L-G:1800 N-G:1740 IEC/EN 61643-116 800 UL1449 X 1200 X X 1400 X X 1700 X 1900 X X L-L:1070 L-L:1200 L-N/G:680 L-N/G:800 X L-L:1780 L-L:1900 X L-N/G:1280 L-N/G:1400 X Notes: 1. Nominal Discharge Current (In)(A): The nominal discharge current is a measure of the SPDs endurance capability; 15 impulses of discharge current uses the 8/20us current waveform. 2. Maximum Discharge Current (Imax)(A): The maximum discharge current is a measure of the SPDs maximum capability; single impulse of discharge current uses the 8/20us current waveform. 3. MLV – UL1449 Measured limiting voltage; the highest value of residual voltage measurements during the application of impulses of 8/20us nominal discharge current (In); an average voltage value of 15 impulses 4. Up – IEC 61643-11 Voltage protection level; the highest value of residual voltage measurements during the application of impulses of 8/20us nominal discharge current (In); a rounding voltage value of maximum measurement. 5. MCOV/UC: Maximum Continuous Operating Voltage - maximum r.m.s. voltage that could be continuously applied to the SPD. 6. Part Numbers LSP05xxxPM Only. 7. * = - P or PM 8. Repetitive Surge Withstanding: 15 strikes at 5,000A (8/20us) with steady MLV/Up. Figure 1. Repetitive Surge Capability for LSP05 Pulse Rating (8x20µSec) 100000 MODEL SIZE = 20MM TA = -55oC TO 85oC 130 to 625VM(AC) RATING 1 SURGE CURRENT (A) 10000 2 15 10 2 1000 10 4 10 5 6 10 10 3 100 ∞ Strikes Surge 1 10,000A 2 7,000A 15 5,000A 100 1,500A 1,000 700A 10 1 10 100 1000 10000 IMPULSE DURATION (μs) FIGURE 10. © 2019 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 11/04/19 Surge Protection Module LED Lighting Surge Protection Module > LSP05 Application/Installation Schematic Dimensions Typical Dimensions (mm) 56.0 ±0.5 L L or N /G L L N N A C/ D C Pow er S upp ly G + - L E D M o du le 48.7±1.5 Parallel Connection 2x ø4.8±0.2 Wi th L E D ind icatin g S PD statu s - ON (g ree n ): S PD is o n lin e - OFF : S PD n ee d s rep lacem en t 10 0 ±20 49.0±1.5 10 0 ±20 L 6 ±2 6 ±2 64.0 ±1 .5 NC L E D n o rma lly o n LS P05 xxx PM R 3 indication wires all use the AW G22. 32.5±1.0 2.3 ±0.2 R1 R2 R3 S PD L or N /G L L N N A C/ D C Pow er S upp ly G + - L E D M o du le R1 Parallel Co nn ection S PD LED Normally Off R2 R3 Wi th L E D ind icatin g S PD statu s LS P05 xxx PM - OFF : S PD is o n lin e - ON (red ): S PD n ee d s rep lacem en t R Notes: 1. LED indicator and associated circuitry are not included in the module. 2. R1 must be capped off by wire nut when not connected (NC). 3. R1 and R2 are AC line voltage (hot); R3 is AC neutral voltage. 4. R2 voltage is cut off when SPD needs replacement. 5. R is current limiting resistor; it resistance/wattage is determined by AC line voltage and desired current driving LED. Example: AC line voltage 240V, LED: 1.6mA, resistor: 150Kohm/0.5W. LSP05XXXXXP L L L N N A C/ D C Pow er LSP05XXXXXPM L Notes: 1. Black: Line; White: Neutral; Green: Ground (P/N with suffix X3333/X3316: Brown: Line; Blue: Neutral; GreenYellow stripe: Ground) 2. Black: R1; Red: R2; Blue: R3 3. Wire Gauge: AWG16 wire Line in, AWG22 Wire for indication; Wire Length: 100mm or customized N /G or + S upp ly - L E D M o du le G Parallel Connection S PD Part Numbering System LSP 05 Device F amily Lit telfuse Surge P 480LL P Xxxxx rotection Module Nominal Disc har ge Cur rent (In ) Oper ating Vo ltag e Connection mode LL: fo r L,L,N/G Blank: L -N, L -G, N-G L L N N A C/ D C Pow er S upp ly G + - L E D M o du le P or PM (P: parallel connection; PM: parallel connection and with monitor indication wire) Other non-standar d option: Parallel Co nn ection (for Class II Unearthed) S PD ~X3316 X3333: with GND wire connection, av ailable fo r 240V ac and 277V ac rating with CE Marking fo r Class I earthed inst allatio n W ire Color: Line: Bro wn, Neutral: Blue, Ground/P: Green with ye llow strip e 331 6: without GND wire connection option Wire Color: Line: Br ow n, Neutral: Blue Disclaimer Notice - Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of and test each product selected for their own applications. Littelfuse products are not designed for, and may not be used in, all applications. Read complete Disclaimer Notice at http://www.littelfuse.com/disclaimer-electronics. © 2019 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 11/04/19