MKP1V120RLG

Thyristors Surface Mount – 120V - 240V > MKP1V120 Series MKP1V120 Series Pb Description Bidirectional devices designed for direct interface with the ac power line. Upon reaching the breakover voltage in each direction, the device switches from a blocking state to a low voltage on−state. Conduction will continue like a Triac until the main terminal current drops below the holding current. The plastic axial lead package provides high pulse current capability at low cost. Glass passivation insures reliable operation. Features • High Pressure Sodium Vapor Lighting • Strobes and Flashers • Ignitors • High Voltage Regulators • Pulse Generators Axial Lead • Used to Trigger Gates of SCR’s and Triac AXIAL LEAD CASE 59 STYLE 2 • Indicates UL Registered − File #E128662 • These are Pb−Free Devices Functional Diagram Additional Information Datasheet Resources Samples © 2017 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 08/30/17 Thyristors Surface Mount – 120V - 240V > MKP1V120 Series Maximum Ratings (TJ = 25°C unless otherwise noted) Rating Symbol Peak Repetitive Off−State Voltage (Note 1) VDRM, (− 40 to 125°C, Sine Wave, 50 to 60 Hz, Gate Open) VRRM MKP1V120 / MKP1V130 / MKP1V160 / MCR25MG ±90 Unit V ±180 MCR25NG On-State RMS Current (All Conduction Angles; TL = 80°C, Value ±0.9 A ITSM ±4.0 A Operating Junction Temperature Range TJ -40 to +125 °C Storage Temperature Range Tstg -40 to +150 °C Lead Length = 3/8") IT Peak Non-Repetitive Surge Current (60 Hz One Cycle, Sine Wave, TJ = 125°C) (RMS) Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. Thermal Characteristics Rating Thermal Resistance, Junction−to−Lead Lead Length = 3/8" Lead Solder Temperature (Lead Length ≥ 1/16" from Case, 10 s Max) Symbol Value R8JL 40 TL 260 Unit °C/W °C © 2017 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 08/30/17 Thyristors Surface Mount – 120V - 240V > MKP1V120 Series Electrical Characteristics - OFF (TJ = 25°C unless otherwise noted; Electricals apply in both directions) Characteristic Symbol Min Typ Max Unit IDRM - - 5.0 µA Repetitive Peak Off−State Current TJ = 25ºC (50 to 60 Hz Sine Wave) VDRM = 90V, MKP1V120, MKP1V130 and MKP1V160 VDRM = 180V, MKP1V240 Electrical Characteristics - ON (TJ = 25°C unless otherwise noted; Electricals apply in both directions) Characteristic Symbol 35 µA MKP1V120 35 µA MKP1V130 Breakover Voltage Min Typ Max 110 _ 130 120 _ 140 Unit V VBO 200µA MKP1V160 150 _ 170 35 µA MKP1V240 220 _ 250 VTM – 1.3 1.5 V Dynamic Holding Current (Sine Wave, 50 to 60 Hz, RL = 100 Ohm) IH _ _ 100 mA Switching Resistance (Sine Wave, 50 to 60 Hz) RS 0.1 _ _ kΩ Peak On−State Voltage (ITM = 1 A Peak, Pulse Width ≤ 300 µs, Duty Cycle ≤ 2%) Dynamic Characteristics Characteristic Symbol Min Typ Max Unit Critical Rate−of−Rise of On−State Current, Critical Damped Waveform Circuit (IPK = 130 Amps, Pulse Width = 10 µsec) dv/dt _ 120 − V/µs © 2017 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 08/30/17 Thyristors Surface Mount – 120V - 240V > MKP1V120 Series Voltage Current Characteristic of SCR Symbol VDRM Parameter Peak Repetitive Forward Off State Voltage IDRM Peak Forward Blocking Current VRRM Peak Repetitive Reverse Off State Voltage IRRM Peak Reverse Blocking Current VTM Maximum On State Voltage I S I IS I S) S IH S I (I S ) Holding Current Figure 1. Maximum Lead Temperature Figure 2. Maximum Ambient Temperature IT(RMS), ON-STATE CURRENT (AMPS) 1.0 TJ = 125°C Sine Wave Conduction Angle = 180 °C 0.8 Assembled in PCB Lead Length =3/8ʺ 0.6 0.4 0.2 0 20 40 60 80 100 120 °C) ( TA, MAXIMUM AMBIENT TEMPERATURE Figure 3. Typical On−State Voltage Figure 4. Typical Power Dissipation © 2017 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 08/30/17 140 Thyristors Surface Mount – 120V - 240V > MKP1V120 Series Figure 7. Typical RMS Current Derating VBO , BREAKOVER VOLTAGE (NORMALIZED) Figure 9. Typical Exponential Static dv/dt Versus Peak Voltage Figure 10. Typical Exponential Static dv/dt Vs Junction Temperature 1.0 0.9 0.8 -60 -40- 20 02 0 40 600 81 100 20 140 TJ, JUNCTION TEMPERATURE ϒ ( C) Figure 11. Maximum Non−Repetitive Surge Current IPK, PEAK CURRENT (AMPS) 100 10 IPK 10% tw 1.0 0.1 1.0 10 100 tw, PULSE WIDTH (ms) © 2017 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 08/30/17 Thyristors Surface Mount – 120V - 240V > MKP1V120 Series Part Marking System Dimensions B K AXIAL LEAD CASE 59 STYLE 2 D F A POLARITY INDICATOR OPTIONAL AS NEEDED (SEE STYLES) F K Ordering Information Dim A Inches Millimeters Min Max Min Max 0.161 0.205 4.10 5.20 B 0.079 0.106 2.00 2.70 D 0.028 0.034 0.71 0.86 F −−− 0.050 −−− 1.27 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. ALL RULES AND NOTES ASSOCIATED WITH JEDEC DO−41 OUTLINE SHALL APPLY 4. POLARITY DENOTED BY CATHODE BAND. Device Package* MKP1V120RLG Shipping 5000 / Tape & Reel MKP1V130RLG MKP1V160G DO−41, Axial Lead MKP1V160RLG MKP1V240G MKP1V240RLG 5. LEAD DIAMETER NOT CONTROLLED WITHIN F DIMENSION. 1000 Units / Bulk 5000 / Tape & Reel 1000 Units / Bulk 5000 / Tape & Reel *This package is inherently Pb−Free. STYLE 2: NO POLARITY Disclaimer Notice - Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of and test each product selected for their own applications. Littelfuse products are not designed for, and may not be used in, all applications. Read complete Disclaimer Notice at: www.littelfuse.com/disclaimer-electronics © 2017 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 08/30/17