P0080EBMCRP2

SIDACtor Device SIDACtor Device TO-92 SIDACtor solid state protection devices protect telecommunications equipment such as modems, line cards, fax machines, and other CPE. SIDACtor devices are used to enable equipment to meet various regulatory requirements including GR 1089, ITU K.20, K.21, and K.45, IEC 60950, UL 60950, and TIA-968-A (formerly known as FCC Part 68) . Electrical Parameters Part Number * VDRM Volts VS Volts VT Volts IDRM µAmps IS mAmps IT Amps IH mAmps CO pF P0080E_ 6 25 4 5 800 2.2 50 100 P0300E_ 25 40 4 5 800 2.2 50 110 P0640E_ 58 77 4 5 800 2.2 150 50 P0720E_ 65 88 4 5 800 2.2 150 50 P0900E_ 75 98 4 5 800 2.2 150 50 P1100E_ 90 130 4 5 800 2.2 150 40 P1300E_ 120 160 4 5 800 2.2 150 40 P1500E_ 140 180 4 5 800 2.2 150 40 P1800E_ 170 220 4 5 800 2.2 150 30 P2300E_ 190 260 4 5 800 2.2 150 30 P2600E_ 220 300 4 5 800 2.2 150 30 P3100E_ 275 350 4 5 800 2.2 150 30 P3500E_ 320 400 4 5 800 2.2 150 30 * For individual “EA”, “EB”, and “EC” surge ratings, see table below. General Notes: • All measurements are made at an ambient temperature of 25 °C. IPP applies to -40 °C through +85 °C temperature range. • IPP is a repetitive surge rating and is guaranteed for the life of the product. • Listed SIDACtor devices are bi-directional. All electrical parameters and surge ratings apply to forward and reverse polarities. • VDRM is measured at IDRM. • VS is measured at 100 V/µs. • Special voltage (VS and VDRM) and holding current (IH) requirements are available upon request. • Off-state capacitance (CO) is measured at 1 MHz with a 2 V bias and is a typical value for “EA” and “EB” product. “EC” capacitance is approximately 2x the listed value. The off-state capacitance of the P0080EB is equal to the “EC” device. Surge Ratings Series IPP 2x10 µs Amps IPP 8x20 µs Amps A 150 150 90 50 45 20 500 B 250 250 150 100 80 30 500 C 500 400 200 150 100 50 500 http://www.littelfuse.com +1 972-580-7777 IPP 10x160 µs Amps IPP 10x560 µs Amps 2 - 16 IPP 10x1000 µs Amps ITSM 60 Hz Amps di/dt Amps/µs © 2004 Littelfuse, Inc. SIDACtor® Data Book and Design Guide SIDACtor Device Thermal Considerations Package Symbol TO-92 Parameter Value Unit TJ Operating Junction Temperature Range -40 to +150 °C TS Storage Temperature Range -65 to +150 °C 90 °C/W Thermal Resistance: Junction to Ambient Data Sheets RθJA IPP – Peak Pulse Current – %IPP +I +I IITT ISS IH IDRM -V -V +V +V V VTT V VDRM DRM V VS S Peak Value 100 tr = rise time to peak value td = decay time to half value Waveform = tr x td 50 Half Value 0 0 tr td t – Time (µs) -I -I V-I Characteristics tr x td Pulse Wave-form IH 8 6 25 ˚C 4 2 IH (TC = 25 ˚C) 10 Ratio of Percent of VS Change – % 14 12 0 -4 2.0 1.8 1.6 1.4 25 ˚C 1.2 1.0 0.8 0.6 0.4 -40 -20 0 -6 -8 -40 -20 0 20 40 60 80 100 120 140 160 Case Temperature (TC) – ˚C 20 40 60 80 100 120 140 160 Junction Temperature (TJ) – ˚C Normalized VS Change versus Junction Temperature © 2004 Littelfuse, Inc. SIDACtor® Data Book and Design Guide Normalized DC Holding Current versus Case Temperature 2 - 17 http://www.littelfuse.com +1 972-580-7777