P0084UAMCLRP

SIDACtor ® Protection Thyristors Broadband OptimizedTM Protection MC Multiport Series - MS-013 RoHS Pb e3 Description The MC Multiport Series MS-013 are low capacitance SIDACtor® thyristors designed to protect broadband equipment from damaging overvoltage transients. The series provides a dual port surface mount solution that enables equipment to comply with various global regulatory standards while limiting the impact to broadband signals. Features and Benefits • Low voltage overshoot Protectors, for applications that demand greater signal integrity • Low on-state voltage Agency Approvals Agency • Does not degrade surge capability after multiple surge events within limit. Agency File Number E133083 • Replaces four discrete components • Pb-free E3 means 2nd level interconnect is Pb-free and the terminal finish material is tin(Sn) (IPC/JEDEC J-STD609A.01) • Fails short circuit when surged in excess of ratings Pinout Designation 1 6 • Two-pair protection 2 5 • 40% lower capacitance than our Baseband 3 4 Applicable Global Standards Schematic Symbol • TIA-968-A • GR 1089 Intra-building • TIA-968-B • IEC 61000-4-5 2nd edition (T1) 1 6 (T2) (G1) 2 5 (G2) • ITU K.20/21/45 Basic Level (R1) 3 4 (R2) • GR 1089 Inter-building • ITU K.20/21/45 Enhanced Level • YD/T 1082 • YD/T 993 • YD/T 950 Electrical Characteristics Part Number Marking VS VDRM VS VDRM @lDRM=5µA @100V/µs @lDRM=5µA @100V/µs V V Pins 1-2, 3-2, 4-5, 6-5 P0084UCMCLxx P0304UCMCLxx P0644UCMCLxx P0724UCMCLxx P0904UCMCLxx P1104UCMCLxx P1304UCMCLxx P0084UCMC P0304UCMC P0644UCMC P0724UCMC P0904UCMC P1104UCMC P1304UCMC 6 25 58 65 75 90 120 25 40 77 88 98 130 160 Notes: - Absolute maximum ratings measured at TA= 25ºC (unless otherwise noted). - Components are bi-directional. - XX Part Number Suffix: ‘TP’ (Tube Pack) or ‘RP’ (Reel Pack). V V Pins 1-3, 4-6 12 50 116 130 150 180 240 50 80 154 176 196 260 320 IH IS IT mA min mA max A max 50 50 150 150 150 150 150 800 800 800 800 800 800 800 VT @IT= 2.2 Amps Capacitance V max 2.2 8 2.2 8 2.2 8 See 2.2 8 Capacitance Values Table 2.2 8 2.2 8 2.2 8 Table continues on next page. © 2017 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 02/23/17 SIDACtor ® Protection Thyristors Broadband OptimizedTM Protection Electrical Characteristics (continued) VDRM VS VDRM VS @lDRM=5µA @100V/µs @lDRM=5µA @100V/µs Part Number Marking V V V Pins 1-2, 3-2, 4-5, 6-5 P1504UCMCLxx P1804UCMCLxx P2304UCMCLxx P2604UCMCLxx P3104UCMCLxx P3504UCMCLxx P1504UCMC P1804UCMC P2304UCMC P2604UCMC P3104UCMC P3504UCMC 140 170 190 220 275 320 IS VT @IT= 2.2 Amps IT V Pins 1-3, 4-6 180 220 260 300 350 400 IH 280 340 380 440 550 600 mA min mA max A max 360 440 520 600 700 800 150 150 150 150 150 150 800 800 800 800 800 800 2.2 2.2 2.2 2.2 2.2 2.2 Capacitance V max 8 8 8 8 8 8 See Capacitance Values Table Notes: - Absolute maximum ratings measured at TA= 25ºC (unless otherwise noted). - Components are bi-directional. - XX Part Number Suffix: ‘TP’ (Tube Pack) or ‘RP’ (Reel Pack). Capacitance Values Part Number pF Pin 1-2 / 3-2 (4-5 / 6-5) Tip-Ground, Ring-Ground pF Pin 1-3 (4-6) Tip-Ring MIN MAX MIN MAX 35 25 55 50 45 45 40 35 35 30 30 30 25 75 45 85 75 70 70 60 55 50 50 45 45 40 20 10 30 25 25 25 20 20 15 15 15 15 15 45 25 50 45 40 40 35 35 30 30 30 25 25 P0084UCMCLxx P0304UCMCLxx P0644UCMCLxx P0724UCMCLxx P0904UCMCLxx P1104UCMCLxx P1304UCMCLxx P1504UCMCLxx P1804UCMCLxx P2304UCMCLxx P2604UCMCLxx P3104UCMCLxx P3504UCMCLXx Note: Off-state capacitance (CO) is measured at 1 MHz with a 2 V bias. Surge Ratings Series IPP C ITSM 50/60 Hz di/dt A min A min A/µs max 200 30 500 0.2/310 1 0.5/700 2 2/10 1 2/10 2 8/20 1 1.2/50 2 10/160 1 10/160 2 10/560 1 10/560 2 5/320 1 9/720 2 10/360 1 10/360 2 10/1000 1 10/1000 2 5/310 1 10/700 2 A min A min A min A min A min A min A min A min 50 500 400 200 150 200 175 100 Notes: 1 Current waveform in µs 2 Voltage waveform in µs - Peak pulse current rating (IPP) is repetitive and guaranteed for the life of the product that remains in thermal equilibrium. - IPP ratings applicable over temperature range of -40ºC to +85ºC - The component must initially be in thermal equilibrium with -40°C < TJ < +150°C © 2017 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 02/23/17 SIDACtor ® Protection Thyristors Broadband OptimizedTM Protection Thermal Considerations Package Symbol Parameter Value Unit TJ Operating Junction Temperature Range -40 to +150 °C TS Storage Temperature Range -65 to +150 °C R0JA Thermal Resistance: Junction to Ambient 60 °C/W Modified MS-013 6 5 4 1 2 3 V-I Characteristics tr x td Pulse Waveform IT IS IH IDRM -V +V VT VDRM VS IPP – Peak Pulse Current – %IPP +I tr = rise time to peak value td = decay time to half value Peak Value 100 Waveform = tr x td 50 Half Value 0 0 td tr t – Time (µs) -I Normalized VS Change vs. Junction Temperature Normalized DC Holding Current vs. Case Temperature 8 6 25 °C 4 IH (TC = 25ºC) IH 10 Ratio of Percent of VS Change – % 2.0 14 12 2 0 -4 -6 1.8 1.6 1.4 1.0 0.8 0.6 0.4 -8 -40 -20 0 20 40 60 80 100 120 140 160 Junction Temperature (TJ) – °C 25°C 1.2 -40 -20 0 20 40 60 80 100 120 140 160 Case Temperature (TC) - ºC Additional Information Datasheet Resources Samples © 2017 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 02/23/17 SIDACtor ® Protection Thyristors Broadband OptimizedTM Protection Soldering Parameters - Temperature Min (Ts(min)) Pre Heat - Temperature Max (Ts(max)) - Time (Min to Max) (ts) Pb-Free assembly (see Fig. 1) +150°C +200°C 60-180 secs. Average ramp up rate (Liquidus Temp (TL) to peak) 3°C/sec. Max. TS(max) to TL - Ramp-up Rate 3°C/sec. Max. Reflow - Temperature (TL) (Liquidus) +217°C - Temperature (tL) 60-150 secs. Peak Temp (TP) +260(+0/-5)°C Time within 5°C of actual Peak Temp (tp) 30 secs. Max. Ramp-down Rate 6°C/sec. Max. Time 25°C to Peak Temp (TP) 8 min. Max. Do not exceed +260°C Physical Specifications Lead Material Copper Alloy Terminal Finish 100% Matte-Tin Plated Body Material UL Recognized epoxy meeting flammability classification V-0 Part Numbering P xxx 4 UC MC L RP TYPE P = SIDACtor MEDIAN VOLTAGE CONSTRUCTION VARIABLE PACKAGE TYPE REEL PACK RoHS COMPLIANT MC Series IPP RATING Figure 1 TP tP Critical Zone TL to TP Ramp-up Temperature Reflow Condition TL TS(max) tL Ramp-down Preheat TS(min) tS 25 time to peak temperature (t 25ºC to peak) Time Environmental Specifications High Temp Voltage Blocking 80% Rated VDRM (VAC Peak ) +125°C or +150°C, 504 or 1008 hrs. MIL-STD-750 (Method 1040) JEDEC, JESD22-A-101 Temp Cycling -65°C to +150°C, 15 min. dwell, 10 up to 100 cycles. MIL-STD-750 (Method 1051) EIA/JEDEC, JESD22-A104 Biased Temp & Humidity 52 VDC (+85°C) 85%RH, 504 up to 1008 hrs. EIA/ JEDEC, JESD22-A-101 High Temp Storage +150°C 1008 hrs. MIL-STD-750 (Method 1031) JEDEC, JESD22-A-101 Low Temp Storage -65°C, 1008 hrs. Thermal Shock 0°C to +100°C, 5 min. dwell, 10 sec. transfer, 10 cycles. MIL-STD-750 (Method 1056) JEDEC, JESD22-A-106 Autoclave (Pressure Cooker Test) +121°C, 100%RH, 2atm, 24 up to 168 hrs. EIA/ JEDEC, JESD22-A-102 Resistance to Solder Heat +260°C, 30 secs. MIL-STD-750 (Method 2031) Moisture Sensitivity Level 85%RH, +85°C, 168 hrs., 3 reflow cycles (+260°C Peak). JEDEC-J-STD-020, Level 1 MS-013 Part Marking Drawing_2009-03-05.eps Part Marking XXXXXXXXX Part Marking Code (Refer to Electrical Characteristics Table) Date Code XXXXX © 2017 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 02/23/17 SIDACtor ® Protection Thyristors Broadband OptimizedTM Protection Dimensions — MS-013 Inches Dimensions 0.065 (1.65) Pad Outline C 0.138 (3.50) D J 7º TYP A Dimension are in inches (and millimeters). 0.059 (1.50) E 7º TYP A B C D E F G H J K BSC* 0.460 (11.68) G Burr Side H 96º A Mold Split Line 4º A 7º TYP BSC* F 7º TYP MIN Length of Flat K Detail A B Millimeters Min Max Min Max 0.360 0.352 0.400 0.043 0.047 0.293 0.289 0.089 0.041 0.020 0.133 0.364 0.356 0.412 0.045 0.055 0.297 0.293 0.093 0.049 9.14 8.94 10.16 1.09 1.19 7.44 7.34 2.26 1.04 0.51 3.38 9.25 9.04 10.46 1.13 1.40 7.54 7.44 2.36 1.24 0.143 3.63 * BSC = Basic Spacing between Centers Packing Options Package Type Description U Quantity Added Suffix Industry Standard Modified MS-013 6-pin Tape and Reel Pack 1500 RP EIA-481-D Modified MS-013 6-pin Tube Pack 500 (50 per tube) TP N/A Tape and Reel Specification — MS-013 .157 (4.0) .630 (16.0) .472 (12.0) 12.99 (330) .512 (13.0) Arbor Hole Dia. Dimensions are in inches (and millimeters) 0.700 (17.8) Direction of Feed Tube Pack Dimensions — MS-013 Message Location .045 (1.14) .310 (7.87) 90˚ .165 (4.19) 6 Interior of the Tube .150 (3.81) .225 (5.72) .525 (13.34) .020 ± .005 WALL TYP. (0.51 ± 0.13) .108 (2.74) .005 A 20.000 ± .030 (508.00 ± 0.76) .110 (2.79) A Dimensions are in inches (and millimeters) Disclaimer Notice - Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of and test each product selected for their own applications. Littelfuse products are not designed for, and may not be used in, all applications. Read complete Disclaimer Notice at www.littelfuse.com/disclaimer-electronics. © 2017 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 02/23/17