P0300S3NLRP

SIDACtor ® Protection Thyristors High Surge Current Protection SIDACtor® Series - DO-214AB Pb e3 RoHS Description SIDACtor® Series DO-214AB (Surface Mount) package are designed to protect low data rate interface and outdoor data interface such as RS-232 or RS-423 in industrial market. They provide a surface mount solution that enables equipment to comply with global regulatory standards. The component’s switching threshold Vs and on-state voltage VT are much lower than traditional Gas Discharge Tube (GDT) technology. Features and Benefits • Low voltage overshoot • Low on-state voltage • Component properties do not degrade after multiple surge events within its limits Agency Approvals Agency Agency File Number • Fast response in microseconds • 2nd level interconnect is Pb-free per IPC/JEDEC J-STD-609A.01 • Fails short circuit when surged in excess of ratings E133083 Applicable Global Standards Pinout Designation Not Applicable Schematic Symbol • TIA-968-A • GR 1089 Intra-building • TIA-968-B • IEC 61000-4-5 • ITU K.20/21 Enhanced Level • YD/T 1082 • ITU K.20/21 Basic Level • YD/T 950 • YD/T 993 • GR 1089 Inter-building Electrical Characteristics Part Number Marking P0080S3NLRP P0300S3NLRP P-8N P03N VDRM @lDRM=5µA VS @100V/µs V min V max 6 30 25 45 IH IS IT mA min mA max A max 50 50 800 800 2.2 2.2 VT @IT=2.2A Capacitance @1MHz, 2V bias V max pf min pF max 4 4 80 80 150 150 Notes: - Absolute maximum ratings measured at TA= 25ºC (unless otherwise noted). - Components are bi-directional (unless otherwise noted). Surge Ratings IPP Series N 8/201 1.2/502 ITSM 50 / 60 Hz di/dt A min A min A/µs max 2500 250 630 © 2016 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 05/24/16 Notes: 1 Current waveform in µs 2 Voltage waveform in µs - Peak pulse current rating (IPP) is repetitive and guaranteed for the life of the product. - IPP ratings applicable over temperature range of -40ºC to +85ºC - The device must initially be in thermal equilibrium with -40°C < TJ < +150°C SIDACtor® Series DO-214AB SIDACtor ® Protection Thyristors High Surge Current Protection Thermal Considerations Package DO-214AB Symbol Parameter Value Unit TJ Operating Junction Temperature Range -65 to +150 °C TS Storage Temperature Range -65 to +150 °C R0JA Thermal Resistance: Junction to Ambient 75 °C/W V-I Characteristics tr x td Pulse Waveform IT IS IH IDRM -V +V VT VDRM VS IPP – Peak Pulse Current – %IPP +I Peak Value 100 tr = rise time to peak value td = decay time to half value Waveform = tr x td 50 Half Value 0 0 td tr t – Time (µs) -I Normalized VS Change vs. Junction Temperature Normalized DC Holding Current vs. Case Temperature IH 10 8 6 25 °C 4 Ratio of Percent of VS Change – % 12 IH (TC = 25ºC) 2.0 14 2 0 -4 -6 1.8 1.6 1.4 1.0 0.8 0.6 0.4 -8 -40 -20 0 20 40 60 80 100 120 140 160 Junction Temperature (TJ) – °C © 2016 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 05/24/16 25°C 1.2 -40 -20 0 20 40 60 80 100 120 140 160 Case Temperature (TC) - ºC SIDACtor® Series DO-214AB SIDACtor ® Protection Thyristors High Surge Current Protection Soldering Parameters Pb-Free assembly (see Fig. 1) +150°C +200°C 60-180 secs. - Temperature Min (Ts(min)) Pre Heat - Temperature Max (Ts(max)) - Time (Min to Max) (ts) Average ramp up rate (Liquidus Temp (TL) to peak) 3°C/sec. Max. TS(max) to TL - Ramp-up Rate 3°C/sec. Max. Reflow - Temperature (TL) (Liquidus) +217°C - Temperature (tL) 60-150 secs. Peak Temp (TP) +260(+0/-5)°C Time within 5°C of actual Peak Temp (tp) 30 secs. Max. Ramp-down Rate 6°C/sec. Max. Time 25°C to Peak Temp (TP) 8 min. Max. Do not exceed +260°C Physical Specifications TP tP Critical Zone TL to TP Ramp-up TL TS(max) tL Ramp-down Preheat TS(min) tS 25 time to peak temperature (t 25ºC to peak) Time Environmental Specifications Lead Material Copper Alloy Terminal Finish 100% Matte-Tin Plated Body Material Figure 1 Temperature Reflow Condition UL recognized epoxy meeting flammability classification V-0 Part Numbering High Temp Voltage Blocking 80% Rated VDRM (VAC Peak ) +125°C or +150°C, 504 or 1008 hrs. MIL-STD-750 (Method 1040) JEDEC, JESD22-A-101 Temp Cycling -65°C to +150°C, 15 min. dwell, 10 up to 100 cycles. MIL-STD-750 (Method 1051) EIA/JEDEC, JESD22-A104 Biased Temp & Humidity 52 VDC (+85°C) 85%RH, 504 up to 1008 hrs. EIA/ JEDEC, JESD22-A-101 High Temp Storage +150°C 1008 hrs. MIL-STD-750 (Method 1031) JEDEC, JESD22-A-101 Low Temp Storage -65°C, 1008 hrs. Thermal Shock 0°C to +100°C, 5 min. dwell, 10 sec. transfer, 10 cycles. MIL-STD-750 (Method 1056) JEDEC, JESD22-A-106 Autoclave (Pressure Cooker Test) +121°C, 100%RH, 2atm, 24 up to 168 hrs. EIA/ JEDEC, JESD22-A-102 Resistance to Solder Heat +260°C, 30 secs. MIL-STD-750 (Method 2031) Moisture Sensitivity Level 85%RH, +85°C, 168 hrs., 3 reflow cycles (+260°C Peak). JEDEC-J-STD-020, Level 1 Part Marking P xxx 0 S3 N L RP TYPE P: SIDACtor MEDIAN VOLTAGE CONSTRUCTION VARIABLE REEL PACK RoHS COMPLIANT Pxxxx xxxxx Part Marking Code (Refer to Electrical Characteristics Table) Date Code IPP RATING PACKAGE TYPE © 2016 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 05/24/16 SIDACtor® Series DO-214AB SIDACtor ® Protection Thyristors High Surge Current Protection DO-214AA (SMB J-Bend) Dimensions — DO-214AB Inches Dimensions C A B H D F E G L K J Dimension in inches and (millimeters) I Millimeters Min Max Min Max A 0.114 0.126 2.900 3.200 B 0.260 0.280 6.600 7.110 C 0.220 0.245 5.590 6.220 D 0.079 0.103 2.060 2.620 E 0.030 0.060 0.760 1.520 F - 0.008 - 0.203 G 0.305 0.320 7.750 8.130 H 0.006 0.012 0.152 0.305 I 0.129 - 3.300 - 2.400 J 0.094 - K - 0.165 L 0.094 - 4.200 2.400 - Solder Pads (all dimensions in mm) Packing Options Package Type S3 Description Quantity Added Suffix Industry Standard DO-214AB Tape and Reel Pack 3000 RP EIA-481-D tape and reel specification Tape and Reel Specification — DO-214AB 0.157 (4.0) 0.472 (12.0) 0.36 (9.2) 0.315 (8.0) 0.059 DIA (1.5) 12.99 (330.0) 0.512 (13.0) Arbor Hole Dia. 0.49 (12.4) © 2016 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 05/24/16 Cover tape Dimensions are in inches (and millimeters). Direction of Feed SIDACtor® Series DO-214AB