P0640Q12ALRP

SIDACtor® Protection Thyristors Broadband OptimizedTM Protection Q2L Series - 3x3 QFN RoHS Pb e3 Description Q2L Series 3x3 QFN are low capacitance SIDACtor® thyristors designed to protect high density broadband equipment from damaging overvoltage transients. The series provides a low profile surface solution that enables broadband equipment to comply with global regulatory standards while limiting the impact to broadband signals and board space. Agency Approvals Features and Benefits Agency • Low voltage overshoot Agency File Number • RoHS Compliant and Halogen-Free • Low on-state voltage E133083 • Pb-free E3 means 2nd level interconnect is Pb-free and the terminal finish material is tin(Sn) (IPC/JEDEC J-STD-609A.01) • Low capacitance • Does not degrade surge capability after multiple surge events within limit. Schematic Symbol • Small footprint • Recognized to UL 497B as an Isolated Loop Circuit • Fails short circuit when Protector surged in excess of ratings Applicable Global Standards Additional Information Datasheet Resources Samples • TIA-968-A • GR 1089 Inter-building* • TIA-968-B • GR 1089 Intra-building • ITU K.20/21/45 Enhanced Level* • YD/T 1082 • YD/T 993 • ITU K.20/21/45 Basic Level • YD/T 950 • IEC 61000-4-5 2nd edition * A/B-Rated parts require series resistance © 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 05/08/20 SIDACtor® Protection Thyristors Broadband OptimizedTM Protection Electrical Characteristics Part Number Marking P0080Q12ALRP P0300Q12ALRP P0640Q12ALRP P0720Q12ALRP P0900Q12ALRP P1100Q12ALRP P1200Q12ALRP P1300Q12ALRP P1500Q12ALRP P1800Q12ALRP P2000Q12ALRP P2300Q12ALRP P2500Q12ALRP P2600Q12ALRP P3100Q12ALRP P3500Q12ALRP P0080Q12BLRP P0300Q12BLRP P0640Q12BLRP P0720Q12BLRP P0900Q12BLRP P1100Q12BLRP P1200Q12BLRP P1300Q12BLRP P1500Q12BLRP P1800Q12BLRP P2000Q12BLRP P2300Q12BLRP P2500Q12BLRP P2600Q12BLRP P3100Q12BLRP P3500Q12BLRP P-8A P03A P06A P07A P09A P11A P12A P13A P15A P18A P20A P23A P25A P26A P31A P35A P-8B P03B P06B P07B P09B P11B P12B P13B P15B P18B P20B P23B P25B P26B P31B P35B V DRM @lDRM=5µA V min 6 25 58 65 75 90 100 120 140 170 180 190 230 220 275 320 6 25 58 65 75 90 100 120 140 170 180 190 230 220 275 320 VS @100V/µs V max 25 40 77 88 98 130 130 160 180 220 220 260 290 300 350 450 25 40 77 88 98 130 130 160 180 220 220 260 290 300 350 400 IH mA min IS mA max IT A max 50 50 150 150 150 150 150 150 150 150 150 150 150 150 150 150 50 50 150 150 150 150 150 150 150 150 150 150 150 150 150 150 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 Capacitance @1MHz, 2V bias pF Min pF Max 25 55 15 35 40 60 40 60 35 55 30 50 30 50 25 45 25 40 25 35 25 35 25 35 25 35 25 35 20 35 20 30 25 55 15 35 40 60 40 60 35 55 30 50 30 50 25 45 25 40 25 35 25 35 25 35 25 35 25 35 20 35 20 30 VT@ IT = 2.2Amps V max 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 Notes: - Absolute maximum ratings measured at TA= 25ºC (unless otherwise noted). - Components are bi-directional. Surge Ratings ITSM Ipp Series 2/10µs 1.2/50µs/8/20µs 10/160µs 10/560µs 10/1000µs 50 / 60 Hz di/dt A min A min A min A min A min A min A/µs max A 150 150 90 50 45 20 500 B 250 250 150 100 80 25 500 Notes: - Peak pulse current rating (IPP) is repetitive and guaranteed for the life of the product. - IPP ratings applicable over temperature range of -40ºC to +85ºC - The component must initially be in thermal equilibrium with -40°C < TJ < +150°C Thermal Considerations Package Symbol Value Unit 3x3 QFN TJ Operating Junction Temperature Range -40 to +150 °C TS Storage Temperature Range -65 to +150 °C 120 °C/W RƟJA Parameter Thermal Resistance: Junction to Ambient © 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 05/08/20 SIDACtor® Protection Thyristors Broadband OptimizedTM Protection tr x td Pulse Waveform V-I Characteristics IPP – Peak Pulse Current – %IPP +I IT IS IH IDRM -V +V VT VDRM VS tr = rise time to peak value td = decay time to half value Peak Value 100 Waveform = tr x td 50 Half Value 0 td tr 0 t – Time (µs) -I Normalized VS Change vs. Junction Temperature Normalized DC Holding Current vs. Case Temperature Percent of VS Change – % 10 IH 8 6 25 °C 2 0 -4 1.8 1.6 1.4 0.8 0.6 -6 0.4 -8 -40 -20 0 25°C 1.2 1.0 Ratio of 4 IH (TC = 25ºC) 2.0 14 12 -40 20 40 60 80 100 120 140 160 -20 0 20 40 60 80 100 120 140 160 Case Temperature (TC) - ºC Junction Temperature (TJ) – °C Soldering Parameters Reflow Condition Pre Heat Pb-Free assembly - Temperature Min (Ts(min)) +150°C - Temperature Max (Ts(max)) +200°C - Time (Min to Max) (ts) 60-180 secs. Figure 1 TP - Temperature (TL) (Liquidus) +217°C - Temperature (tL) 60-150 secs. Peak Temp (TP) +260(+0/-5)°C Time within 5°C of actual Peak Temp (tp) 30 secs. Max. Ramp-down Rate 6°C/sec. Max. Time 25°C to Peak Temp (TP) 8 min. Max. Do not exceed +260°C Temperature Reflow 3°C/sec. Max. Critical Zone TL to TP Ramp-up Average ramp up rate (Liquidus Temp (TL) to peak) 3°C/sec. Max. TS(max) to TL - Ramp-up Rate tP TL T S(max) tL Ramp-down T S(min) Preheat tS 25 time to peak temperature (t 25ºC to peak) Time © 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 05/08/20 SIDACtor® Protection Thyristors Broadband OptimizedTM Protection Physical Specifications Environmental Specifications Lead Material Copper Alloy Terminal Finish 100% Matte-Tin Plated UL Recognized epoxy meeting flammability classification V-0 Body Material High Temp Voltage Blocking 80% Rated VDRM (VAC Peak ) +125°C or +150°C, 504 or 1008 hrs. MIL-STD-750 (Method 1040) JEDEC, JESD22-A-101 Temp Cycling -65°C to +150°C, 15 min. dwell, 10 up to 100 cycles. MIL-STD-750 (Method 1051) EIA/ JEDEC, JESD22-A104 52 VDC (+85°C) 85%RH, 504 up to 1008 hrs. EIA/JEDEC, JESD22-A-101 +150°C 1008 hrs. MIL-STD-750 (Method 1031) High Temp Storage JEDEC, JESD22-A-101 Low Temp Storage -65°C, 1008 hrs. 0°C to +100°C, 5 min. dwell, 10 sec. transfer, Thermal Shock 10 cycles. MIL-STD-750 (Method 1056) JEDEC, JESD22-A-106 Resistance to Solder Heat +260°C, 30 secs. MIL-STD-750 (Method 2031) 85%RH, +85°C, 168 hrs., 3 reflow cycles Moisture Sensitivity Level (+260°C Peak). JEDEC-J-STD-020, Level 1 Biased Temp & Humidity Can be A or B Dimensions — 3x3 QFN TOP VIEW C A A E J B F 2.15 1.93 END VIEW N2 N1 H K1 SIDE VIEW M1 M2 Inches Dimensions BOTTOM VIEW 0.585 K2 Recommended Soldering Pad Outline (Reference Only) Part Numbering Max Min Max 0.114 0.122 2.900 3.100 3.100 B 0.114 0.122 2.900 C 0.075 0.083 1.900 2.100 E 0.011 0.019 0.285 0.485 2.130 F 0.076 0.084 1.930 H 0.035 0.043 0.900 1.100 J 0.000 0.008 0.000 0.200 K1 0.004 0.012 0.100 0.300 K2 0.004 0.012 0.100 0.300 M1 0.056 0.064 1.430 1.630 M2 0.038 0.046 0.970 1.170 N1 0.096 0.104 2.440 2.640 N2 0.082 0.090 2.080 2.280 Part Marking Terminals on Back P xxx 0 Q12 x L RP TYPE P = SIDACtor MEDIAN VOLTAGE CONSTRUCTION VARIABLE Millimeters Min REEL PACK RoHS COMPLIANT IPP RATING XXXX XXXXX Part Marking Code (Refer to Electrical Characteristics Table) Date code PACKAGE TYPE Packing Options Package Type Q12 Description Quantity 3x3 QFN Tape and Reel Pack 5000 Added Suffix RP Industry Standard EIA-481-D © 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 05/08/20 SIDACtor® Protection Thyristors Broadband OptimizedTM Protection Tape and Reel Dimensions — 3x3 QFN Reel Dimension Symbols C A D N W1 B Tape Leader and Trailer Dimensions END START CARRIER TAPE COVER TAPE TRAILER 160mm MIN LEADER 400mm MIN Tape Dimension Items D0 P0 P2 T CARRIER TAPE D1 B0 F W0 K0 P1 A0 E1 E2W Description Inches Millimeters Min Max Min Max N/A 12.992 N/A 330.0 A Reel Diameter B Drive Spoke Width 0.059 N/A 1.50 C Arbor Hole Diameter 0.504 0.531 12.80 13.50 D Drive Spoke Diameter 0.795 N/A 20.20 N/A N Hub Diameter 1.969 N/A 50.00 N/A W1 Reel Inner Width at Hub 0.488 0.567 12.40 14.40 A0 Pocket Width at bottom 0.126 0.134 3.20 3.40 B0 Pocket Length at bottom 0.126 0.134 3.20 3.40 D0 Feed Hole Diameter 0.059 0.063 1.50 1.60 D1 Pocket Hole Diameter 0.059 N/A 1.50 N/A E1 Feed hole position 1 0.065 0.073 1.65 1.85 E2 Feed hole position 2 0.400 0.408 10.15 10.35 F Feed hole center-Pocket hole 0.215 0.219 5.45 5.55 K0 Pocket Depth 0.039 0.051 1.00 1.30 P0 Feed Hole Pitch 0.153 0.161 3.90 4.10 P1 Component Spacing 0.311 0.319 7.90 8.10 P2 Feed hole center-Pocket hole 0.077 0.081 1.95 2.05 T Carrier Tape Thickness 0.010 0.014 0.25 0.35 W Embossed Carrier Tape Width 0.453 0.484 11.50 12.30 W0 Cover Tape Width 0.358 0.366 9.10 9.30 N/A COVER TAPE Disclaimer Notice - Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of and test each product selected for their own applications. Littelfuse products are not designed for, and may not be used in, all applications. Read complete Disclaimer Notice at: www.littelfuse.com/disclaimer-electronics. © 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 05/08/20