P0641DF-1E

SIDACtor ® Protection Thyristors SLIC Protection Fixed Voltage Enhanced Single Port Series - MS-012 RoHS Pb e3 Description The MS-012 packaged Fixed Voltage Enhanced Single Port Series consists of SIDACtor® components designed to protect sensitive SLICs (Subscriber Line Interface Circuit) from damaging overvoltage transients. The series provides single port protection using a fixed voltage switching device for negative surges. Positive surges are routed though enhanced switching diodes to a ground reference. The series is also pin-to-pin compatible to industry standard programmable SO-8 SLIC protectors. Features & Benefits Agency Approvals Agency • Integrated fast switching diodes for positive voltage surges Agency File Number E133083 • Fails short circuit when surged in excess of ratings • RoHS Compliant and LeadFree Pinout • Single port protection in one package • Pb-free E3 means 2nd level interconnect is Pb-free and the terminal finish material is tin(Sn) (IPC/JEDEC J-STD-609A.01) (Tip) 1 8 (Tip) (NC) 2 7 (Ground) • Low voltage overshoot (NC) 3 6 (Ground) • Low on-state voltage (Ring) 4 5 (Ring) • Pin-to-pin SO-8 compatible footprint Schematic Symbol • Does not degrade surge capability after multiple surge events within limit Applicable Global Standards 1 8 2 7 3 4 • TIA-968-A • GR 1089 Intra-building* • TIA-968-B • IEC 61000-4-5 2nd edition 6 • ITU K.20/21 Enhanced Level • YD/T 1082 5 • ITU K.20/21 Basic Level • YD/T 993 • YD/T 950 • GR 1089 Inter-building* * Series resistance required Electrical Characteristics Part Number P0641DF-1E P0721DF-1E P0901DF-1E P0991DF-1E P1001DF-1E P1101DF-1E P1301DF-1E P1501DF-1E P1701DF-1E Marking P0641F1E P0721F1E P0901F1E P0991F1E P1001F1E P1101F1E P1301F1E P1501F1E P1701F1E VDRM@ IDRM=5µA VS@100V/µs IH IS IT@VT VT@IT=1 Amps VF@25° V min V max mA min mA max A max V max V max 58 65 75 80 85 95 120 140 160 77 88 98 104 110 130 165 180 200 150 150 150 150 150 150 150 150 150 800 800 800 800 800 800 800 800 800 1 1 1 1 1 1 1 1 1 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 Capacitance See Capacitance Values Table Notes: - Absolute maximum ratings measured at TA= 25ºC (unless otherwise noted). - Components are not appropriate for positive ringing systems - All electrical characteristics shown are defined from Tip (pins 1 & 8) to Ground (pins 6 & 7), and Ring (pins 4 & 5) to ground (pins 6 & 7) - VF < 8.5 volts @ 10 / 700µs, 37.5 Amps © 2019 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 02/26/19 SIDACtor ® Protection Thyristors SLIC Protection Capacitance Values pF Pin 1,8-6,7 / 4,5-6,7 Tip-Ground, Ring-Ground MIN MAX 40 90 35 85 30 80 25 75 25 75 25 70 20 70 20 70 Part Number P0641DF-1E P0721DF-1E P0901DF-1E P0991DF-1E P1001DF-1E P1101DF-1E P1301DF-1E P1701DF-1E pF Pin 1,8-4,5 Tip-Ring MIN MAX 20 45 20 45 20 40 15 35 15 35 15 30 15 30 15 30 Note: Off-state capacitance (CO) is measured at 1 MHz with a 2V bias Surge Ratings IPP Series F ITSM di/dt 2/10 1.2/50 - 8/20 10/700 - 5/310 10/1000 600VRMS 1s A min A min A min A min A min Amps/µs max 120 100 50 30 1 500 Notes: - Peak pulse current rating (IPP) is repetitive and guaranteed for the life of the product that is in thermal equilibrium. - IPP ratings applicable over temperature range of -40ºC to +85ºC - The component must initially be in thermal equilibrium with -40°C < TJ < +150°C Thermal Considerations Package MS-012 1 2 3 8 7 6 Symbol Parameter Value Unit TJ Operating Junction Temperature Range -40 to +150 °C TS Storage Temperature Range -65 to +150 °C R0JA Thermal Resistance: Junction to Ambient 120 °C/W 5 4 V-I Characteristics tr x td Pulse Waveform VF VS VDRM VT -V +V IDRM IH IS IT IPP – Peak Pulse Current – %IPP +I Peak Value 100 Waveform = tr x td 50 Half Value 0 0 -I © 2019 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 02/26/19 tr = rise time to peak value td = decay time to half value tr td t – Time (µs) SIDACtor ® Protection Thyristors SLIC Protection Normalized DC Holding Current vs. Case Temperature 2.0 12 1.8 10 IH 8 6 25 °C 4 IH (TC = 25ºC) 14 2 0 -4 1.6 1.4 25°C 1.2 1.0 Ratio of Percent of VS Change – % Normalized VS Change vs. Junction Temperature 0.8 0.6 -6 0.4 -8 -40 -20 0 -40 20 40 60 80 100 120 140 160 -20 0 20 40 60 80 100 120 140 160 Case Temperature (TC) - ºC Junction Temperature (TJ) – °C Soldering Parameters - Temperature Min (Ts(min)) Pre Heat - Temperature Max (Ts(max)) - Time (Min to Max) (ts) Pb-Free assembly (see Fig. 1) +150°C +200°C 60-180 secs. Average ramp up rate (Liquidus Temp (TL) to peak) 3°C/sec. Max. TS(max) to TL - Ramp-up Rate 3°C/sec. Max. Reflow - Temperature (TL) (Liquidus) +217°C - Temperature (tL) 60-150 secs. Peak Temp (TP) +260(+0/-5)°C Time within 5°C of actual Peak Temp (tp) 30 secs. Max. Ramp-down Rate 6°C/sec. Max. Time 25°C to Peak Temp (TP) 8 min. Max. Do not exceed +260°C Physical Specifications Lead Material Copper Alloy Terminal Finish 100% Matte-Tin Plated Body Material UL Recognized compound meeting flammability rating V-0 Additional Information Datasheet Resources Samples Figure 1 TP tP Critical Zone TL to TP Ramp-up Temperature Reflow Condition TL TS(max) tL Ramp-down Preheat TS(min) tS 25 time to peak temperature (t 25ºC to peak) Time Environmental Specifications High Temp Voltage Blocking 80% Rated VDRM (VDC ) +125°C or +150°C, 504 or 1008 hrs. MIL-STD-750 (Method 1040) JEDEC, JESD22-A-101 Temp Cycling -65°C to +150°C, 15 min. dwell, 10 up to 100 cycles. MIL-STD-750 (Method 1051) EIA/JEDEC, JESD22-A104 Biased Temp & Humidity 52 VDC (+85°C) 85%RH, 504 up to 1008 hrs. EIA/ JEDEC, JESD22-A-101 High Temp Storage +150°C 1008 hrs. MIL-STD-750 (Method 1031) JEDEC, JESD22-A-101 Low Temp Storage -65°C, 1008 hrs. Thermal Shock 0°C to +100°C, 5 min. dwell, 10 sec. transfer, 10 cycles. MIL-STD-750 (Method 1056) JEDEC, JESD22-A-106 Autoclave (Pressure Cooker Test) +121°C, 100%RH, 2atm, 24 up to 168 hrs. EIA/ JEDEC, JESD22-A-102 Resistance to Solder Heat +260°C, 30 secs. MIL-STD-750 (Method 2031) Moisture Sensitivity Level 85%RH, +85°C, 168 hrs., 3 reflow cycles (+260°C Peak). JEDEC-J-STD-020, Level 1 © 2019 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 02/26/19 SIDACtor ® Protection Thyristors SLIC Protection Dimensions — MS-012 Inches Dimension MIN A A1 A2 B C D E E1 e L o Recommended Soldering Pad Outline (Reference Only) Millimeters MAX 0.053 0.069 0.004 0.010 0.043 0.065 0.012 0.020 0.007 0.010 0.189 0.197 0.228 0.244 0.150 0.157 0.050 BSC* 0.016 0.050 MIN MAX 1.35 1.75 0.10 0.25 1.25 1.65 0.31 0.51 0.17 0.25 4.80 5.00 5.80 6.20 3.80 4.00 1.27 BSC* 0.40 1.27 * BSC = Basic Spacing between Centers Part Numbering Part Marking P xxx 1 DF -1E SINGLE ENHANCED TYPE P: SIDACtor IPP RATING MEDIAN VOLTAGE PACKAGE TYPE CONSTRUCTION VARIABLE Part Number Code (Refer to Electrical Characteristics Table) XXXXXF1E o XXXXX Date Code Packing Options Package Type Description Quantity Added Suffix Industry Standard D MS-012 SMT 8-pin SOIC Tape and Reel Pack 2500 N/A EIA-481-D Tape and Reel Specifications — MS-012 1.55 (.061) 4.0 (.158) DIMENSIONS ARE: 2.0 (.079) 8.0 (.315) 0.8 MIN. (0.03) 5.5 (.216) o 6.4 (.252) 1.50 ø MIN. (.059) Carrier Tape Embossment 0.512 (13.0) Arbor Hole Dia. MILLIMETERS (INCHES) 0.40 (0.016) 12.0 (.472) Cover 0 MIN. Direction of Feed Tape 2.1 (.083) 12.99 (330.0) Dimensions are in inches (and millimeters). 0.49 (12.4) Direction of Feed Disclaimer Notice - Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of and test each product selected for their own applications. Littelfuse products are not designed for, and may not be used in, all applications. Read complete Disclaimer Notice at www.littelfuse.com/disclaimer-electronics. © 2019 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 02/26/19