P0901CA2RP

Twin SLIC Protector Twin SLIC Protector 1 (T) 2 (G) 3 (R) Subscriber Line Interface Circuits (SLIC) are highly susceptible to transient voltages, such as lightning and power cross conditions. To minimize this threat, Littelfuse provides this dual-chip, fixed-voltage SLIC protector device. For specific design criteria, see details in Figure 3.29. Electrical Parameters VDRM Volts Part Number * VS Volts Pins 1-2, 3-2 VT Volts VF Volts IDRM µAmps IS mAmps IT Amps IH mAmps CO pF P0641CA2 58 77 4 5 5 800 1 120 60 P0721CA2 65 88 4 5 5 800 1 120 60 P0901CA2 75 98 4 5 5 800 1 120 60 P1101CA2 95 130 4 5 5 800 1 120 60 P1701CA2 160 200 4 5 5 800 1 120 70 * For surge ratings, see table below. General Notes: • All measurements are made at an ambient temperature of 25 °C. IPP applies to -40 °C through +85 °C temperature range. • IPP is a repetitive surge rating and is guaranteed for the life of the product. • VDRM is measured at IDRM. • VS and VF are measured at 100 V/µs. • Special voltage (VS and VDRM) and holding current (IH) requirements are available upon request. • Off-state capacitance (CO) is measured across pins 1-2 or 3-2 at 1 MHz with a 2 V bias. Capacitance across pins 1-3 is approximately half. • Parallel capacitive loads may affect electrical parameters. • Compliance with GR 1089 or UL 60950 power cross tests may require special design considerations. Contact the factory for further information. Surge Ratings (Preliminary Data) Series IPP 2x10 µs Amps IPP 8x20 µs Amps IPP 10x160 µs Amps IPP 10x560 µs Amps IPP 10x1000 µs Amps ITSM 60 Hz Amps di/dt Amps/µs A 150 150 90 50 45 20 500 http://www.littelfuse.com +1 972-580-7777 2 - 44 © 2004 Littelfuse, Inc. SIDACtor® Data Book and Design Guide Twin SLIC Protector Thermal Considerations Package Symbol Modified DO-214AA TJ Operating Junction Temperature Range -40 to +150 °C TS Storage Temperature Range -65 to +150 °C 85 °C/W Pin 3 Parameter Value Thermal Resistance: Junction to Ambient RθJA Unit Pin 2 +I +I VS VDRM IS IH VT IDRM -V -V IPP – Peak Pulse Current – %IPP VF IT VT IDRM VDRM IH IS +V +V VS Peak Value 100 tr = rise time to peak value td = decay time to half value Waveform = tr x td 50 Half Value 0 IT 0 td tr t – Time (µs) -I -I V-I Characteristics tr x td Pulse Wave-form 8 6 4 25 ˚C Ratio of 2 IH (TC = 25 ˚C) 10 IH Percent of VS Change – % 14 12 0 -4 2.0 1.8 1.6 1.4 25 ˚C 1.2 1.0 0.8 0.6 0.4 -40 -20 0 -6 20 40 60 80 100 120 140 160 Case Temperature (TC) – ˚C -8 -40 -20 0 20 40 60 80 100 120 140 160 Junction Temperature (TJ) – ˚C Normalized VS Change versus Junction Temperature © 2004 Littelfuse, Inc. SIDACtor® Data Book and Design Guide Normalized DC Holding Current versus Case Temperature 2 - 45 http://www.littelfuse.com +1 972-580-7777 Data Sheets Pin 1