P1500GALRP

SIDACtor ® Protection Thyristors Baseband Protection (Voice-DS1) SIDACtor® Series - DO-15 RoHS Pb e3 Description The DO-15 series are designed to protect baseband equipment such as modems, line cards, CPE and DSL from damaging overvoltage transients. The series provides a cost-effective through-hole solution that enables equipment to comply with global regulatory standards. Features and Benefits • Low voltage overshoot • Fails short circuit when surged in excess of ratings • Low on-state voltage • Does not degrade surge capability after multiple surge events within limit. Agency Approvals Agency Agency File Number • 2nd level interconnect is Pb-free per IPC/ JEDEC J-STD-609A.01 • RoHS compliant, leadfree and halogen-free. • Low capacitance E133083 Applicable Global Standards Pinout Designation Not Applicable Schematic Symbol • TIA-968-A • GR 1089 Intra-building • TIA-968-B • IEC 61000-4-5 2nd edition • ITU K.20/21/45 Enhanced Level* • YD/T 1082 • YD/T 993 • ITU K.20/21/45 Basic Level • YD/T 950 • GR 1089 Inter-building* * A/B-rated parts require series resistance Electrical Characteristics Part Number P0080GALRP P1100GALRP P1300GALRP P1500GALRP P1800GALRP P2300GALRP P2600GALRP P3100GALRP P3500GALRP P1100GBLRP P1300GBLRP P1500GBLRP P1800GBLRP P2300GBLRP P2600GBLRP P3100GBLRP P3500GBLRP P4500GBLRP P4500GCLRP Marking VDRM @lDRM=5µA VS @100V/µs P-8A P11A P13A P15A P18A P23A P26A P31A P35A P11B P13B P15B P18B P23B P26B P31B P35B P45B P45C V min 6 90 120 140 170 190 220 275 320 90 120 140 170 190 220 275 320 400 400 V max 25 130 160 180 220 260 300 350 400 130 160 180 220 260 300 350 400 530 530 IH IS mA min mA max 50 800 150 800 150 800 150 800 150 800 150 800 150 800 150 800 150 800 150 800 150 800 150 800 150 800 150 800 150 800 150 800 150 800 150 800 50 800 IT VT @IT=2.2 Amps A max 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 V max 4 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 Capacitance @1MHz, 2V bias pF min 10 30 25 25 25 25 25 10 20 30 25 25 25 25 25 20 20 20 20 pF max 30 60 40 40 40 30 30 20 30 60 40 40 40 30 30 30 30 45 45 Notes: - Absolute maximum ratings measured at TA= 25ºC (unless otherwise noted). - Components are bi-directional. © 2017 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 02/23/17 SIDACtor ® Protection Thyristors Baseband Protection (Voice-DS1) Surge Ratings IPP Series ITSM 10/560 1 10/560 2 10/1000 1 10/1000 2 5/310 1 10/700 2 50 / 60 Hz Amps min Amps min Amps min Amps min A 50 45 - 20 B 100 80 100 25 C - - 150 25 Notes: 1 Current waveform in µs 2 Voltage waveform in µs - Peak pulse current rating (IPP) is repetitive and guaranteed for the life of the product that remains in thermal equilibrium. - IPP ratings applicable over temperature range of -40 to +85ºC - The component must initially be in thermal equilibrium with -40°C < TJ < +150°C Thermal Considerations Package Symbol DO-15 Parameter Value Unit TJ Operating Junction Temperature Range -40 to +150 °C TS Storage Temperature Range -65 to +150 °C 60 °C/W R0JA Thermal Resistance: Junction to Ambient Soldering Parameters - Temperature Min (Ts(min)) Pre Heat - Temperature Max (Ts(max)) - Time (Min to Max) (ts) Pb-Free assembly (see Fig. 1) +150°C +200°C 60-180 secs. Average ramp up rate (Liquidus Temp (TL) to peak) 3°C/sec. Max. TS(max) to TL - Ramp-up Rate 3°C/sec. Max. Reflow - Temperature (TL) (Liquidus) +217°C - Temperature (tL) 60-150 secs. Peak Temp (TP) +260(+0/-5)°C Time within 5°C of actual Peak Temp (tp) 30 secs. Max. Ramp-down Rate 6°C/sec. Max. Time 25°C to Peak Temp (TP) 8 min. Max. Do not exceed +260°C Additional Information Datasheet Resources © 2017 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 02/23/17 Samples Figure 1 TP tP Critical Zone TL to TP Ramp-up Temperature Reflow Condition TL TS(max) tL Ramp-down Preheat TS(min) tS 25 time to peak temperature (t 25ºC to peak) Time Physical Specifications Lead Material Copper Alloy Terminal Finish 100% Matte-Tin Plated Body Material UL recognized epoxy meeting flammability classification V-0 SIDACtor ® Protection Thyristors Baseband Protection (Voice-DS1) Part Marking Environmental Specifications Part Marking Code Pxxxx XXXXX (Refer to Electrical Characteristics Table) Date Code Part Numbering P xxx 0 G x L RP REEL PACK TYPE P = SIDACtor RoHS COMPLIANT MEDIAN VOLTAGE High Temp Voltage Blocking 80% Rated VDRM (VAC Peak ) +125°C or +150°C, 504 or 1008 hrs. MIL-STD-750 (Method 1040) JEDEC, JESD22-A-101 Temp Cycling -65°C to +150°C, 15 min. dwell, 10 up to 100 cycles. MIL-STD-750 (Method 1051) EIA/JEDEC, JESD22-A104 Biased Temp & Humidity 52 VDC (+85°C) 85%RH, 504 up to 1008 hrs. EIA/ JEDEC, JESD22-A-101 High Temp Storage +150°C 1008 hrs. MIL-STD-750 (Method 1031) JEDEC, JESD22-A-101 Low Temp Storage -65°C, 1008 hrs. Thermal Shock 0°C to +100°C, 5 min. dwell, 10 sec. transfer, 10 cycles. MIL-STD-750 (Method 1056) JEDEC, JESD22-A-106 Autoclave (Pressure Cooker Test) +121°C, 100%RH, 2atm, 24 up to 168 hrs. EIA/ JEDEC, JESD22-A-102 Resistance to Solder Heat +260°C, 30 secs. MIL-STD-750 (Method 2031) Moisture Sensitivity Level 85%RH, +85°C, 168 hrs., 3 reflow cycles (+260°C Peak). JEDEC-J-STD-020, Level 1 IPP RATING CONSTRUCTION Dimensions - DO-15 VARIABLE (Revised 11/14/07) PACKAGE TYPE Dimensions — DO-15 D Tape and Reel Specification — DO-15 B L G L A Dimension Inches Spacing off center, either side 0.039 (1.0) B 2.55 (64.8) TYP Millimeters MIN MAX MIN MAX B 0.028 0.034 0.711 0.864 D 0.12 0.14 3.048 3.556 G 0.235 0.27 5.969 6.858 L 1 C E D Dimensions are in inches (and millimeters). 3.15 (80.0) TYP 25.4 recess depth max 0.75” G F Direction of Feed Packing Options Package Type Description G DO-15 Axial Tape & Reel Quantity 5000 Added Suffix Industry Standard RP EIA-RS296-D Symbols Description Inches MM A Component Spacing (lead to lead) 0.200 ± 0.020” 5.08 ± 0.508 B C D E F G Inner Tape Pitch Tape Width Max. Off Alignment Reel Dimension Max. Hub Recess Max. Abor Hole 2.062 ± 0.059” 0.250” 0.048” 13” 3” 0.68” 52.37 ± 1.498 6.35 1.219 330.2 76.19 17.27 Disclaimer Notice - Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of and test each product selected for their own applications. Littelfuse products are not designed for, and may not be used in, all applications. Read complete Disclaimer Notice at www.littelfuse.com/disclaimer-electronics. © 2017 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 02/23/17