P1800ECMCL

SIDACtor ® Protection Thyristors Broadband OptimizedTM Protection MC Series - TO-92 Pb e3 RoHS Description The MC Series TO-92 are low capacitance SIDACtor® thyristors designed to protect broadband CPE equipment such as VoIP and DSL Modems from damaging overvoltage transients. The series provides a through-hole solution that enables CPE equipment to comply with global regulatory standards while limiting the impact to broadband signals. Features and Benefits • Low voltage overshoot • 40% lower capacitance than our Baseband Protectors, for applications that demand greater signal integrity • Low on-state voltage Agency Approvals Agency • Does not degrade surge capability after multiple surge events within limit Agency File Number E133083 • Pb-free E3 means 2nd level interconnect is Pbfree and the terminal finish material is tin(Sn) (IPC/JEDEC J-STD609A.01) • Fails short circuit when surged in excess of ratings Pinout Designation • RoHS Compliant Pin 1 Applicable Global Standards Pin 3 Schematic Symbol • TIA-968-A • GR 1089 Intra-building • TIA-968-B • IEC 61000-4-5 2nd edition • ITU K.20/21/45 Enhanced Level • ITU K.20/21/45 Basic Level • YD/T 1082 • YD/T 993 • YD/T 950 • GR 1089 Inter-building Electrical Characteristics Part Number Marking P0080ECMCLxxx P0300ECMCLxxx P0640ECMCLxxx P0720ECMCLxxx P0900ECMCLxxx P1100ECMCLxxx P1300ECMCLxxx P1500ECMCLxxx P1800ECMCLxxx P2300ECMCLxxx P2600ECMCLxxx P3100ECMCLxxx P3500ECMCLxxx P0080ECMC P0300ECMC P0640ECMC P0720ECMC P0900ECMC P1100ECMC P1300ECMC P1500ECMC P1800ECMC P2300ECMC P2600ECMC P3100ECMC P3500ECMC VDRM @lDRM=5µA VS @100V/µs V min V max 6 25 58 65 75 90 120 140 170 190 220 275 320 25 40 77 88 98 130 160 180 220 260 300 350 400 Notes: - Absolute maximum ratings measured at TA= 25ºC (unless otherwise noted). - Components are bi-directional. - XXX Part Number Suffix: ‘AP’ (Ammo Pack), or ‘RP1’ or ‘RP2’ (Reel Pack),. © 2017 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 02/23/17 IH IS mA min mA max 50 50 150 150 150 150 150 150 150 150 150 150 150 800 800 800 800 800 800 800 800 800 800 800 800 800 IT VT @IT=2.2 Amps Capacitance @1MHz, 2V bias A max V max pF min pF max 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 4 4 4 4 4 4 4 4 4 4 4 4 4 35 25 55 50 45 45 40 35 35 30 30 30 25 75 45 85 75 70 70 60 55 50 50 45 45 40 SIDACtor ® Protection Thyristors Broadband OptimizedTM Protection Series Surge Ratings IPP ITSM 50/60 Hz di/dt A min A min A/µs Max 200 30 500 0.2/310 1 0.5/700 2 2/10 1 2/10 2 8/20 1 1.2/50 2 10/160 1 10/160 2 10/560 1 10/560 2 5/320 1 9/720 2 10/360 1 10/360 2 10/1000 1 10/1000 2 5/310 1 10/700 2 A min A min A min A min A min A min A min A min 50 500 400 200 150 200 175 100 Value Unit C Notes: 1 Current waveform in µs 2 Voltage waveform in µs - Peak pulse current rating (IPP) is repetitive and guaranteed for the life of the product that remains in thermal equilibrium. - IPP ratings applicable over temperature range of -40ºC to +85ºC - The component must initially be in thermal equilibrium with -40°C < TJ < +150°C Thermal Considerations Package Symbol TO-92 Parameter TJ Operating Junction Temperature Range -40 to +150 °C TS Storage Temperature Range -65 to +150 °C 90 °C/W R0JA Thermal Resistance: Junction to Ambient V-I Characteristics tr x td Pulse Waveform IT IS IH IDRM -V +V VT VDRM VS IPP – Peak Pulse Current – %IPP +I tr = rise time to peak value td = decay time to half value Peak Value 100 Waveform = tr x td 50 Half Value 0 0 td tr t – Time (µs) -I Normalized VS Change vs. Junction Temperature Normalized DC Holding Current vs. Case Temperature 2.0 IH 10 8 6 25 °C 4 IH (TC = 25ºC) 12 Ratio of Percent of VS Change – % 14 2 0 -4 -6 -8 -40 -20 0 20 40 60 80 100 120 140 160 Junction Temperature (TJ) – °C 1.8 1.6 1.4 25°C 1.2 1.0 0.8 0.6 0.4 -40 -20 0 20 40 60 80 100 120 140 160 Case Temperature (TC) - ºC © 2017 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 02/23/17 SIDACtor ® Protection Thyristors Broadband OptimizedTM Protection Soldering Parameters Pb-Free assembly (see Fig. 1) +150°C +200°C 60-180 secs. - Temperature Min (Ts(min)) Pre Heat - Temperature Max (Ts(max)) - Time (Min to Max) (ts) Average ramp up rate (Liquidus Temp (TL) to peak) 3°C/sec. Max. TS(max) to TL - Ramp-up Rate 3°C/sec. Max. Reflow - Temperature (TL) (Liquidus) +217°C - Temperature (tL) 60-150 secs. Peak Temp (TP) +260(+0/-5)°C Time within 5°C of actual Peak Temp (tp) 30 secs. Max. Ramp-down Rate 6°C/sec. Max. Time 25°C to Peak Temp (TP) 8 min. Max. Do not exceed +260°C Physical Specifications Lead Material Copper Alloy Terminal Finish 100% Matte-Tin Plated Body Material UL Recognized epoxy meeting flammability classification V-0 Additional Information Datasheet Samples Resources Figure 1 TP tP Critical Zone TL to TP Ramp-up Temperature Reflow Condition TL TS(max) tL Ramp-down Preheat TS(min) tS 25 time to peak temperature (t 25ºC to peak) Time Environmental Specifications High Temp Voltage Blocking 80% Rated VDRM (VAC Peak ) +125°C or +150°C, 504 or 1008 hrs. MIL-STD-750 (Method 1040) JEDEC, JESD22-A-101 Temp Cycling -65°C to +150°C, 15 min. dwell, 10 up to 100 cycles. MIL-STD-750 (Method 1051) EIA/JEDEC, JESD22-A104 Biased Temp & Humidity 52 VDC (+85°C) 85%RH, 504 up to 1008 hrs. EIA/ JEDEC, JESD22-A-101 High Temp Storage +150°C 1008 hrs. MIL-STD-750 (Method 1031) JEDEC, JESD22-A-101 Low Temp Storage -65°C, 1008 hrs. Thermal Shock 0°C to +100°C, 5 min. dwell, 10 sec. transfer, 10 cycles. MIL-STD-750 (Method 1056) JEDEC, JESD22-A-106 Autoclave (Pressure Cooker Test) +121°C, 100%RH, 2atm, 24 up to 168 hrs. EIA/ JEDEC, JESD22-A-102 Resistance to Solder Heat +260°C, 30 secs. MIL-STD-750 (Method 2031) Moisture Sensitivity Level 85%RH, +85°C, 168 hrs., 3 reflow cycles (+260°C Peak). JEDEC-J-STD-020, Level 1 Part Marking XXXXXXX XX Part Numbering P xxx 0 E C MC L xxx TYPE P = SIDACtor MEDIAN VOLTAGE CONSTRUCTION VARIABLE PACKAGE TYPE © 2017 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 02/23/17 PACKING OPTIONS RoHS COMPLIANT MC SERIES IPP RATING XXXXX Part Marking Code (Refer to Electrical Characteristics Table) Date Code SIDACtor ® Protection Thyristors Broadband OptimizedTM Protection Packing Options Package Type Description Packing Options Quantity TO-92 Tape and Reel Pack E 2000 TO-92 Ammo Pack TO-92 Bulk Pack Dimensions — TO-92 Inches A N MT2/PIN 3 E L D Min Max Min Max A 0.176 0.196 4.47 4.98 B 0.500 D 0.095 12.70 0.105 2.41 RP1 0.1 inch (2.54mm) 0.2 inch (5.08mm) AP (Not applicable) EIA-468-B N/A (Not applicable) N/A EIA-481-D E 0.150 0.135 0.145 3.43 3.68 H 0.088 0.096 2.23 2.44 J 0.176 0.186 4.47 4.73 K 0.088 0.096 2.23 2.44 L 0.013 0.019 0.33 0.48 M 0.013 0.017 0.33 0.43 0.02 (0.5) 1.62 0.236 (41.2) (6.0) MAX 0.708 (18.0) 0.354 (9.0) 0.60 1.52 0.125 (3.2) MAX 1.27 (32.2) 0.50 (12.7) 3.81 N 0.25 (6.35) 0.50 (12.7) 2.67 G H Industry Standard RP2 Millimeters G B M Lead Spacing Ammo Pack Specification — TO-92 Temperature Measurement Point MT1/PIN 1 Added Suffix 0.20 (5.08) Flat down ed n of Fe Directio 25 Devices per fold 1.7 (43) Dimensions are in inches (and millimeters). 6.9 (175) All leads are insulated from case. Case is electrically non-conductive. (Rated at 1600 V(AC) RMS for one minute from leads to case over the operating temperature range.) Mold flash shall not exceed 0.13 mm per side. K J The TO-92 is designed to meet mechanical standards as set forth in JEDEC publication number 95. 0.157 DIA (4.0) 1.7 (43) 12.9 (327) Tape and Reel Specification — TO-92 FLAT SIDE OF TO-92 A Inches D W1 C B P H1 H W W3 ROUND SIDE OF TO-92 (RP1) W4 (RP2) W2 P0 F F A B C D W1 P P0 F(for RP1) F(for RP2) H H1 W W2 W3 W4 Millimeters Min Max Min Max N/A 4.016 3.386 0.795 1.181 0.496 0.498 0.090 0.182 N/A N/A 0.674 0.354 0.236 0.020 14.173 N/A N/A N/A 1.968 0.504 0.502 0.110 0.244 1.673 1.270 0.763 0.370 N/A N/A N/A 102.0 86.0 20.2 30.0 12.60 12.65 2.29 4.63 N/A N/A 17.12 8.25 6.00 0.50 360.0 N/A N/A N/A 50.0 12.80 12.75 2.80 6.19 42.50 32.26 19.38 9.75 N/A N/A Inches Millimeters Disclaimer furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of and Dimension Notice - Information test each product selected Maximum for their ownMinimum applications. Littelfuse products are not designed for, and may not be used in, all applications. Minimum Maximum Read complete Disclaimer Notice at www.littelfuse.com/disclaimer-electronics. A N/A 14.173 N/A 360.0 B 4.016 N/A 102.0 N/A C 3.386 N/A 86.0 N/A D 0.795 N/A 20.2 N/A W1 1.181 1.968 30.0 50.0 © 2017 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 02/23/17